Kangaroo 2081 User manual

SEW IN COMFORT. SEW LONGER.™
ASSEMBLY INSTRUCTIONS
Mod 2081
ITEM NO.: 2081 White

Assembly InstructionsMod 2081 2
1. Read the instructions carefully before beginning the assembly process to ensure proper assembly
of this product. Please open and inspect the contents of box(es) to see that all parts and hardware
are included.
2. Tools Required
180°
Screw cam bolts flush as
illustrated.
Press cam into hole until flush with
surface. The arrow direction must
be in the direction of the hole.
Insert bolt through pre-drilled
hole in edge of panel.
Turn clockwise to lock cam with bolt.
General Assembly Guidelines
3. Understanding How the Cam Fastener Works
Tip: place a small bit of WD-40 or similar
lubricant into the pre-installed cam bolt
holes to help the cam bolts screw in better.
4. Glue provided is to secure wood dowels in place and is optional. If glue is used during assembly,
locate the appropriate hole for the dowel, place a small amount of glue in the hole and insert the
dowel. Wipe away excess glue immediately. It is not necessary to glue the other end of the dowel
when attaching to other parts.
Use and Care Your cabinet normally requires a minimum amount of maintenance; however, the
following points are worth noting:
Cleaning – To remove marks and enhance the surface, wipe with a gentle all-purpose cleanser. DO NOT
use ammonia-based, harsh chemicals or abrasive cleaning agents. Wipe dry immediately.
Electrical and Hydraulic Lifts – Require annual lubrication with WD-40 or similar lubricant.
Phillips Screwdriver Hammer Electric Screwdriver

Assembly InstructionsMod 2081 3
ITEM DESCRIPTION QT Y. PACK.
DBack Panel 1 1 of 3
FFixed Shelf 1 1 of 3
XLeft Side Panel 1 1 of 3
ZRight Side Panel 1 1 of 3
01 Left Gate Leg 1 1 of 3
O2 Right Gate Leg 1 1 of 3
EPull Out Panel 1 1 of 3
ATop Panel 1 2 of 3
A1 Top Leaf Panel 1 2 of 3
A2 Ironing Board Top 1 2 of 3
ITEM DESCRIPTION QT Y. PACK.
GBottom Panel 1 2 of 3
VDoor 1 2 of 3
LDrawer Front 1 2 of 3
KDrawer Front 1 2 of 3
L1 Drawer Left Side 3 3 of 3
L2 Drawer Right Side 3 3 of 3
L3 Drawer Front/Back 4 3 of 3
L4 Drawer Inner Front 1 3 of 3
L5 Drawer Inner Front 1 3 of 3
L6 Drawer Bottom 3 3 of 3
L7 Thread Board Panel 2 3 of 3
Parts List - Panels
A2
A1
A
O1
O2
X
E
F
D
Z
V
G
L7
L3
L3
L3
L1
L1
L1
L2
L2
L2
L3
L4
K
L5
L
x2
L6
L6
L6

Assembly InstructionsMod 2081 4
6x35 Cam Bolt x70
3.5x14 Screw x79 3x14 Screw x8
Allen Wrench x1 Handle x3
14mm Wrench x1
5⁄8“ Cam Cover x70
Alignment Pin x2
Caster x2 Locking Plate Caster x5
Butt Hinge x10
8x16 Fix Bolt x20
4x24 Fix Bolt x4
8x30 Dowel Pin x46
3.5x30 Screw x12
Magnet x4
Catch Plate x4
Lock x1
Lock Plate x1
Key x2
3x20 Screw x4
c1
b1
s1
a
c2
s3
s5
b2
b3
s2
h
r3
h1
t1
t2
d1
m
L
4x40 Fix Bolt x2
s4
Parts List: Hardware
Adhesive Foam Sheet x1
6x50 Dowel Pin x70
d2
Cam
Pre-installed parts
Drawer RunnersCaster Bracket
c5

Assembly InstructionsMod 2081 5
Part One: Cabinet Shell
We can’t wait to get your brand new Mod 2081 Sewing Cabinet up and running. Please contact our Customer Service Team
at 1-800-533-7347, ext. 1 during normal business hours with any assembly related questions.
8x16 Fix Bolt x20 6x35 Cam Bolt x6
Allen Wrench x1
b1
c1
a
Locking Plate
Caster x5
t2
t2
b1
a
G
G
Top side of panel G
Underside of Panel G
Install 6 c1 Cam Bolts into the top side of
Panel G.
Flip Panel G over, and install
t2 Locking Plate Casters with
b1 Fix Bolts.
Tighten with Allen Wrench.
Set Panel G aside.

Assembly InstructionsMod 2081 6
Part One: Cabinet Shell
6x35 Cam Bolt x10
8x30 Dowel Pin x16
c1
d1
X
Z
Insert 4 c1 Cam Bolts into Panel X
Insert 4 d1 Dowel Pins into Panel X
Insert 4 c1 Cam Bolts into Panel Z
Insert 4 d1 Dowel Pins into Panel Z
Attach L Lock Catch Plate to Panel Z
with s1 Screws.
D
Insert 2 c1 Cam Bolts
into Panel D.
Insert 8 d1 Dowel Pins
into Panel D.
L
Lock Plate x1
3.5x14 Screw x2
s1
s1
L

Assembly InstructionsMod 2081 7
Part One: Cabinet Shell
8x30 Dowel Pin x6
d1
Butt Hinge x3
h1
3.5x14 Screw x9
s1
F
Insert 6 d1 Dowel Pins into Panel F.
Attach 3 h1 Butt Hinges to Panel F
using s1 Screws.
D
F
*ASSEMBLY SHOWN UPSIDE DOWN
Insert c1 Cam Bolts on Panel D into cams on
Panel F. Tighten and apply c2 Cam Covers.
5⁄8“ Cam Cover x2
c2
c5
s1
h1

Assembly InstructionsMod 2081 8
Part One: Cabinet Shell
Z
F
D
X
c5
*ASSEMBLY SHOWN UPSIDE DOWN
Insert c1 Cam Bolts on Panels X and Z into
cams on Panels F and D. Tighten and apply c2
Cam Covers.
5⁄8“ Cam Cover x8
c2

Assembly InstructionsMod 2081 9
Part One: Cabinet Shell
5⁄8“ Cam Cover x6
c2
Insert Cam Bolts on Panel G into cams on Panels X, Z and D. Tighten and apply Cam Covers.
With the help of a friend, turn the cabinet over onto its casters.
Z
D
X
G

Assembly InstructionsMod 2081 10
Part One: Cabinet Shell
h1
s1
O1
O2
Butt Hinge x4
h1
3.5x14 Screw x12
s1
Alignment Pin x2
s5
Caster x2
t1
14mm Wrench x1
r3
Magnet Catch Plate x2
m
s5
s5
s2
m
s2
m
Locate pilot holes on Panels O1 and O2.
Install h1 Butt Hinges using s1 Screws.
Insert s5 Alignment Pin into Panels O1
and O2.
Install t1 Casters into pre-installed
caster brackets on Panels O1 and O2.
Tighten with r3 Wrench.
Attach m Magnet Catch Plate to the un-
derside of Panel O2 with s2 Screws. Set
aside Magnets for use in the next step.
3x14 Screw x4
s2

Assembly InstructionsMod 2081 11
Part One: Cabinet Shell
Locate the pilot holes
on the back of Panel
Dand attach h1 Butt
Hinges on Panels O1
and O2 with s1 Screws.
Insert c1 Cam Bolts into Panel A
Attach m Magnets to Panel A with s1 Screws.
Locate pilot holes in Panel A1. Attach h1 Butt Hinges
to Panel A1 with s1 Screws.
Attach m Magnets to Panel A1 with s1 Screws.
A
A1
3.5x14 Screw x29
s1
6x35 Cam Bolt x6
c1
Magnet x4
m
Butt Hinge x3
h1
D
O1
O2
s1
m
h1
h1
s1
h1
s1

Assembly InstructionsMod 2081 12
Part One: Cabinet Shell
3.5x14 Screw x9
s1
Attach Panel A to Panel A1 with h1 Hinges using
s1 Screws.
Lower top Panels A/A1 onto
cabinet, using Panels O1 and
O2 for support, while inserting
Cam Bolts into Panels D, X and
Z.
Tighten and apply Cam Covers.
5⁄8“ Cam Cover x6
c2
A
A1
A
A1
X
Z
s1
h1

Assembly InstructionsMod 2081 13
Part Two: Drawers - Panel Preparation
L3
L5
L4
x4
L1
L2
x3
x3
6x35 Cam Bolt x48
c1
Insert 6 c1 Cam Bolts into Panel L2. Repeat with 2
remaining panels (3 total).
Insert 6 c1 Cam Bolts into Panel L1. Repeat with 2
remaining panels (3 total).
Insert 2 c1 Cam Bolts into
Panel L3. Repeat with 3
remaining panels (4 total).
Insert 2 c1 Cam Bolts into
Panel L5.
Insert 2 c1 Cam Bolts into
Panel L4.
d1
L6
8x30 Dowel Pin x24
d1
Insert 8 d1 Dowels into the
edges of Panel L6. Repeat with
2 remaining panels (3 total).
x3

Assembly InstructionsMod 2081 14
Part Two: Drawers - Bottom Drawer L4
L3
L4
L6
c5
5⁄8“ Cam Cover x8
c2
L1
L3
L2
L6
L4
Insert Cam Bolts on Panels L3 and L4 into cams on Panel L6. Tighten cam locks on the underside of Panel L6 and apply
Cam Covers.
Insert Cam Bolts on Panels L1 and L2 into cams on Panels L3, L4 and L6. Tighten and apply Cam Covers.
Set bottom drawer aside.

Assembly InstructionsMod 2081 15
L1
L2
L3
L3
L6
Insert Cam Bolts on Panels L1 and L2 into cams on Panels L3 and L6. Tighten and apply Cam Covers.
Set middle drawer aside.
Part Two: Drawers - Middle Drawer L3
5⁄8“ Cam Cover x8
c2
L3
L3
L6
Insert Cam Bolts on Panel L3 into cams on Panel L6. Tighten and apply Cam Covers.

Assembly InstructionsMod 2081 16
Part Two: Drawers - Top Drawer L5
L3
L6
L5
5⁄8“ Cam Cover x8
c2
Insert Cam Bolts on Panels L3 and L5 into cams on Panel L6. Tighten and apply Cam Covers.
L1
L3
L6
L5
L2
Insert Cam Bolts on Panels L1 and L2 into cams on Panels L3, L5 and L6. Tighten and apply Cam Covers.
Set top drawer aside.

Assembly InstructionsMod 2081 17
Part Two: Drawers
E
Carefully remove film from back of
Adhesive Foam Sheet and apply adhesive
side to Panel E, avoiding drawer runners.
Slide drawers into cabinet, align-
ing drawer runners. Be sure that
cabinet runners are fully
extended with ball bearing
pieces pulled to the front.
You may need a friend to help
with this step, but it is not
required.
TIP: Gently open and close the
drawers a few times to engage the
Soft Close mechanism.

Assembly InstructionsMod 2081 18
Part Three: Drawer Fronts
3.5x14 Screw x9
s1
V
s1
h1
h
b2
m
s2
Attach h1 Hinges to Panel V with s1 Screws.
Attach m Magnet Plates to Panel V with s2 Screws.
Attach h Handle to Panel V with b2 Fix Bolts.
Butt Hinge x3
h1
3x14 Screw x4
s2
Magnet Catch Plate x2
m
Handle x1
h
4x24 Fix Bolt x2
b2

Assembly InstructionsMod 2081 19
Part Three: Drawer Fronts
s1
h1
V
F
Locate the pilot holes on Panel V. Align Butt
Hinges already installed on Panel F and
attach with s1 Screws.
3.5x14 Screw x9
s1

Assembly InstructionsMod 2081 20
Part Three: Drawer Fronts
b3
4x40 Fix Bolt x2 3.5x30 Screw x6
s3
Handle x1
h
b3
b3
s3
s3
Connect Panel L to Panel L5 with s3 Screws.
TIP: Screw s3 Screws part of the way through Panel L5 first to make aligning Panel L easier.
Attach h Handle to Panel L/L5 with b3 Fix Bolts.
L5
L