Kangaroo XL User manual

SEW IN COMFORT. SEW LONGER.™
ASSEMBLY INSTRUCTIONS
Mod XL
ITEM NO.: 2071 Hydraulic Lift
2061 Electric Lift

Assembly Instructions2061/2071 2
1. Read the instructions carefully before beginning the assembly process to ensure proper assembly
of this product. Please open and inspect the contents of box(es) to see that all parts and hardware
are included.
2. Tools Required
180°
Screw cam bolts flush as
illustrated.
Press cam into hole until flush with
surface. The arrow direction must
be in the direction of the hole.
Insert bolt through pre-drilled
hole in edge of panel.
Turn clockwise to lock cam with bolt.
General Assembly Guidelines
3. Understanding How the Cam Fastener Works
Tip: place a small bit of WD-40 or similar
lubricant into the pre-installed cam bolt
holes to help the cam bolts screw in better.
4. Glue provided is to secure wood dowels in place and is optional. If glue is used during assembly,
locate the appropriate hole for the dowel, place a small amount of glue in the hole and insert the
dowel. Wipe away excess glue immediately. It is not necessary to glue the other end of the dowel
when attaching to other parts.
Use and Care Your cabinet normally requires a minimum amount of maintenance; however, the
following points are worth noting:
Cleaning – To remove marks and enhance the surface, wipe with a gentle all-purpose cleanser. DO NOT
use ammonia-based, harsh chemicals or abrasive cleaning agents. Wipe dry immediately.
Electrical and Hydraulic Lifts – Require annual lubrication with WD-40 or similar lubricant.
Phillips Screwdriver Hammer Electric Screwdriver
Torque set to 3-5

Assembly Instructions2061/2071 3
Parts List: Panels
ITEM DESCRIPTION QT Y. PACK.
V1 Left Door Panel 1 1 of 3
V2 Right Door Panel 1 1 of 3
Y2 Right Inside Panel 1 1 of 3
Y1 Left Inside Panel 1 1 of 3
XLeft Side Panel 1 1 of 3
ZRight Side Panel 1 1 of 3
ATop Panel 1 2 of 3
A2 Lift Platform 1 2 of 3
ITEM DESCRIPTION QT Y. PACK.
A1 Cover Panel 1 2 of 3
GBottom 1 2 of 3
EShelves 2 2 of 3
DBack Panel 1 2 of 3
A3 Quilt Leaf Panel 1 3 of 3
O1 Left Gateleg Panel 1 3 of 3
O2 Right Gateleg Panel 1 3 of 3
Y1
Y2
X
Z
A3
A
A1
D
E
E
G
V1
V2
A2
O1
O2

Assembly Instructions2061/2071 4
Parts List: Hardware
6x35 Cam Bolt x27
c1
8x30 Dowel Pin x28
d1
5⁄8“ Cam Cover x27
c2
Caster x3
t1
Locking Plate Caster x4
t2
8x16 Fix Bolt x16
b1
5x60 Screw x2
s20
6x6 Screw x4
s7
3.5x14 Screw x80
s1
Handle x2
h
4x20 Fix Bolt x4
b2
Magnet x1
Catch Plate x1
m
Magnet x2
Catch Plate x2
m1
Butt Hinge x9
h1
Alignment Pin x2
s3
5x30 Screw x5
s2
Hinge Body x2
g1
Peg x8
p1
Lift x1
Lift Rail
(Left) x1
Lift Rail
(Right) x1
TIP: Keep all the parts in their individually labeled bags. This will make finding parts easier as you assemble your cabinet.
14mm Wrench x1
r3
Allen Wrench x1
a
Metal Support Bar x1

Assembly Instructions2061/2071 5
Part 1: Main Cabinet
Congratulations and welcome to Kangaroo Sewing Furniture! We can’t wait to get your brand new Mod XL Sewing Cabinet up and
running. Please contact our Customer Service Team at 1-800-533-7347 ext. 1 during normal business hours with any assembly
related questions.
Locking Plate Caster x4
t2
8x16 Fix Bolt x16
b1
Attach t2 Locking Plate Cast-
ers to the underside of Panel G,
using b1 Fix Bolts. Tighten with
Allen Wrench.
Flip Panel G over.
Attach c1 Cam Bolts to Panel G.
Set Panel G aside.
6x35 Cam Bolt x9
c1
G
G
Allen Wrench x1
a

Assembly Instructions2061/2071 6
Part 1: Main Cabinet
6x35 Cam Bolt x4
c1
8x30 Dowel Pin x8
d1
Attach 2 c1 Cam Bolts to Panel
Xas shown.
Insert 4 d1 Dowel Pins into the
edges of Panel X as shown.
Attach 2 c1 Cam Bolts to Panel Z
as shown.
Insert 4 d1 Dowel Pins into the
edges of Panel Z as shown.
X
Z

Assembly Instructions2061/2071 7
Part 1: Main Cabinet
Attach the Left Lift Rail to Panel Y1 with s1 Screws as shown.
Insert d1 Dowel Pins into the edges of Panel Y1 as shown.
TIP: Spray a small amount of WD-40 or similar lubricant onto a paper towel and wipe the
newly installed rails. This will make lift installation and operation easier.
D
Y1
6x35 Cam Bolt x4
c1
8x30 Dowel Pin x14
d1
Lift Rail
(Left) x1
3.5x14 Screw x3
s1
Attach c1 Cam Bolts to Panel D
as shown.
Insert d1 Dowel Pins into the
edges of Panel D as shown.

Assembly Instructions2061/2071 8
Part 1: Main Cabinet
Attach the Right Lift Rail to Panel Y2 with s1 Screws as shown.
TIP: Spray a small amount of WD-40 or similar lubricant onto a paper towel and wipe the newly installed
rails. This will make lift installation and operation easier.
Y2
D
X
Z
Lift Rail
(Right) x1
3.5x14 Screw x3
s1
5⁄8“ Cam Cover x4
c2
NOTE: The above illustration shows upside down
assembly of the cabinet. This is necessary to attach the
bottom.
Attach Panels X and Z to Panel D as shown, inserting
cam bolts into cam locks. Tighten cam locks and apply
c2 Cam Covers.
8x30 Dowel Pin x4
d1

Assembly Instructions2061/2071 9
Part 1: Main Cabinet
Y1
Y2
Z
D
X
5⁄8“ Cam Cover x4
c2
Attach Panels Y1 and Y2 to Panel D as shown, inserting cam bolts into cam locks. Tighten
cam locks and apply c2 Cam Covers.

Assembly Instructions2061/2071 10
Part 1: Main Cabinet
G
Y2
D
Y1
X
Z
G
s20
Z
5⁄8“ Cam Cover x9
c2
5x60 Screw x2
s20
Lower Panel G onto Panels Z, Y2, D, Y1 and X as shown,
inserting cam bolts into cam locks.
Tighten cam locks and apply c2 Cam Covers.
Attach Panel G to Panel Z using s20 Screws as shown.
Make sure casters are locked and flip cabinet over onto
its casters. You may need a friend to help you, but it is not
requred.

Assembly Instructions2061/2071 11
Part 2: Lift
LIFT INSTALLATION WARNING:
DO NOT remove the small wooden block from the Lift until assembly is complete. If the block is removed or falls out
before lift assembly is complete, the cables will retract, making installation difficult. If the
block falls out before complete assembly, Call Customer Service at 1-800-533-7347, ext. 1
for assistance, or visit www.arrowsewing.com/assembly/ and find the
“Alternate Airlift Attachment Steps” video.
This illustration shows the back view of the Lift. Notice the
wooden block and zip tie; the wooden block holds the piston
in place so that the cables can be easily handled and inserted
into the Lift Rails installed on your cabinet.
3.5x14 Screw x4
s1
A2
Attach the Lift to Panel A2 using s1 Screws.

Assembly Instructions2061/2071 12
Part 2: Lift
Guide Lift onto Lift Rails using plastic guides. Insert ends of cable into rail
tabs; make sure the cable is hooked into the rail tabs on both sides.
Cut the zip tie on the wooden block, but DO NOT remove the block yet.
Lower the Lift to first lock position and remove the
wooden block. DO NOT ADJUST LIFT POSITION until the
top is installed, or you risk the Lift
coming out and cables becoming
disengaged.
Plastic guides
Lift rail
Cable
Lift rail
Rail tabs

Assembly Instructions2061/2071 13
Part 3: Top and Shelves
A
s2
c1
m
s1
6x35 Cam Bolt x10
c1
Metal Support Bar x1
5x30 Screw x5
s2
Magnet x1
m
3.5x14 Screw x2
s1
Attach c1 Cam Bolts to Panel
A as shown.
Attach m Magnet to Panel A
with s1 Screws as shown.
Set aside magnet plate for
later use.
Attach the Metal Support Bar
to Panel A with s2 Screws as
shown.

Assembly Instructions2061/2071 14
Part 3: Top and Shelves
A
A2
Y1
X
D
Y2
Z
E
E
p1
p1
5⁄8“ Cam Cover x10
c2
Peg x8
p1
Lower Panel A onto Panels X, Y1,
D, Y2 and Z, inserting cam bolts
into cam locks.
Tighten cam locks and cover with
c2 Cam Covers.
Note the small hole in the back
right corner. See inset illustration;
you will need a long screwdriver to
reach through the hole and tighten
the cam lock.
Insert p1 Pegs into pre-drilled Panels X
and Y1, taking care to be sure the pegs are
evenly spaced.
Slide Panel E shelves into place as shown.
Z
D
Y2

Assembly Instructions2061/2071 15
Part 4: Door
V1
V2
Z
V2
V1
V2
Z
s7
t1
h1
s1
g1
s1
Caster x1
t1
14mm Wrench x1
r3
Butt Hinge x2
h1
Hinge Body x2
g1
3.5x14 Screw x18
s1
6x6 Screw x4
s7
Catch Plate x1
m
Attach t1 Caster to
Panel V1 as shown.
Tighten with
r3 Wrench.
Attach g1 Hinge Body
to Panel V2 as shown.
using s1 Screws.
Attach h1 Butt Hinges,
connecting Panels
V1 and V2 as shown,
using s1 Screws.
Attach m Magnet
Catch Plate using
s1 Screws.
s1
h1
Attach g1 Hinge Body on Panel
V2 to pre-installed door slider
on Panel Z using s7 Screws.
g1

Assembly Instructions2061/2071 16
Part 4: Door - Adjusting the Hinges
Adjust hinge vertically:
Loosen the screws indicated and
slide the hinge body up or down
to adjust vertical position of your
hinge.
Adjust hinge horizontally:
Loosen the screw indicated and
slide the hinge body left or right to
adjust horizontal position of your
hinge.
Adjust door depth:
Loosen the screws indicated and
slide the hinge body in or out to
adjust depth of your door.
For more information on adjusting your hinges, please visit us at www.arrowsewing.com and find our Product Support Videos.

Assembly Instructions2061/2071 17
Part 4: Door
V2
V1
h
b2
Handle x2
h
4x20 Fix Bolt x4
b2
Attach h Handles using b2 Fix Bolts.

Assembly Instructions2061/2071 18
Part 5: Quilt Panel
O2
O1
O2
O1
D
Alignment Pin x2
s3
Caster x2
t1
Butt Hinge x4
h1
Catch Plate x2
m1
3.5x14 Screw x28
s1
Attach m1 Magnet Catch
Plates to Panels O1 and
O2 as illustrated, using s1
Screws.
Set magnets aside for later
m1
s1
s3
h1
s1
t1
Attach h1 Butt Hinges to
Panels O1 and O2 as illus-
trated, using s1 Screws.
Screw s3 Alignment Pins
into the top edges of Panels
O1 and O2 as illustrated.
Attach t1 Casters to Panels
O1 and O2 as illustrated.
Tighten with Wrench.
Attach Panels O1 and O2 to Panel D as il-
lustrated, using s1 Screws to attach h1 Butt
Hinges.
s1
h1
h1
s1
s1
h1
14mm Wrench x1
r3

Assembly Instructions2061/2071 19
Part 5: Quilt Panel
A3
m1
s1
h1
s1
O2
O1
D
A3
s1
Magnet x2
m1
Butt Hinge x3
h1
3.5x14 Screw x22
s1
Attach m1 Magnets to Panel
A3 as illustrated, using s1
Screws. Attach h1 Butt Hinges to
Panel A3 as illustrated, using
s1 Screws.
Balancing Panel A3 on Panels O1 and O2, attach Panel A3 to Panel A with h1
Hinges, using s1 Screws.
s1
h1
s1
h1

Assembly Instructions2061/2071 20
Completed Mod XL Sewing Cabinet