Kangaroo Kiwi K7107 User manual

SEW IN COMFORT. SEW LONGER.™
ASSEMBLY INSTRUCTIONS
Kiwi
ITEM NO.: K7105 Teak
K7107 Gray
K7111 Ash White

Assembly InstructionsKiwi 2
1. Read the instructions carefully before beginning the assembly process to ensure proper assembly
of this product. Please open and inspect the contents of box(es) to see that all parts and hardware
are included.
2. Tools Required
180°
Screw cam bolts flush as
illustrated.
Press cam into hole until flush with
surface. The arrow direction must
be in the direction of the hole.
Insert bolt through pre-drilled
hole in edge of panel.
Turn clockwise to lock cam with bolt.
General Assembly Guidelines
3. Understanding How the Cam Fastener Works
Tip: place a small bit of WD-40 or similar
lubricant into the pre-installed cam bolt
holes to help the cam bolts screw in better.
4. Glue provided is to secure wood dowels in place and is optional. If glue is used during assembly,
locate the appropriate hole for the dowel, place a small amount of glue in the hole and insert the
dowel. Wipe away excess glue immediately. It is not necessary to glue the other end of the dowel
when attaching to other parts.
Use and Care Your cabinet normally requires a minimum amount of maintenance; however, the
following points are worth noting:
Cleaning – To remove marks and enhance the surface, wipe with a gentle all-purpose cleanser. DO NOT
use ammonia-based, harsh chemicals or abrasive cleaning agents. Wipe dry immediately.
Phillips Screwdriver Hammer Electric Screwdriver

Assembly InstructionsKiwi 3
ITEM DESCRIPTION
A1/A2
G
K5
K6
K9
K10
K11
Hardware Pack
Top
Bottom Panel
Left Drawer Side
Right Drawer Side
Left Deep Drawer Side
Right Deep Drawer Side
QTY PACK.
11
1
3
3
1
1
11 of 2
1 of 2
1 of 2
1 of 2
1 of 2
1 of 2
1 of 2
2 of 2
ITEM DESCRIPTION
X
Z
O1
O
K4
K7
K8
Back Panel
Left Side Panel
Right Side Panel
Back Support Panels
Gate Leg
Drawer Back
Deep Drawer Front
Deep Drawer Back
QTY PACK.
1
1
2
1
3
1
1
12 of 2
2 of 2
2 of 2
2 of 2
2 of 2
2 of 2
2 of 2
2 of 2
D
Drawer Bottom 4
K3 Drawer Front 32 of 2
x3
x2
G
A1
A2
D
O1
O1
X
Z
O
K11
K5
K4
K6
K3
K8
K9
K11
K7
K10
K1
IIroning Pad 2 of 2
1
K1 Removable Peg Board 22 of 2
I
Parts List: Panels

Assembly InstructionsKiwi 4
Plate Caster x4 Caster x1
Hinge x2
6x25 Bolt and nut x1
Pre-installed parts
P Brackets x4
c5
p
b
h2
t1
t2
Snag Free Hinge
h4
TIP: Keep all the parts in their individually labeled bags. This will make finding parts easier as you assemble your cabinet.
NOTE: P Brackets shown below are an optional part, used to add extra stability to the back panel of your cabinet. If you choose
not to use them, the function of your cabinet will not be affected.
6x35 Cam Bolt x36 5⁄8“ Cam Cover x60 6x50 Dowel Pin x66
d2
8x30 Dowel Pin x16
d1
c1
c2
3.5x14 Screw x20 3x14 Screw x8
s2
3.5x35 Screw x16
s1
s3
Cam
Drawer Runners
Parts List: Hardware
Handle x4
h1

Assembly InstructionsKiwi 5
Turn the panel over and attach Plate Casters using s1 Screws.
Lock the Casters and flip Panel G over. Set aside.
Congratulations and welcome to Kangaroo Sewing Furniture! We can’t wait to get your brand new Kiwi Storage Cabinet up and
running! Please contact our Customer Service Team at 1-800-533-7347 ext. 1 during normal business hours with any assembly
related questions.
G
Insert Cam Bolts into pre-in-
stalled cam anchors on Panel G.
6x35 Cam Bolt x6
c1
Plate Caster x4
t1
3.5x14 Screw x16
s1
Part One: Cabinet Shell
G

Assembly InstructionsKiwi 6
Z
X
8x30 x8
d1
Insert 4 Dowel Pins in each of the two Panel O1 pieces.
x2
O1
6x35 x8
c1
8x30 x8
d1
Part One: Cabinet Shell
Install 4 Dowel Pins
in Panel Z
Install 4 Cam Bolts
in Panel Z
Install 4 Dowel Pins
in Panel X
Install 4 Cam Bolts
in Panel X

Assembly InstructionsKiwi 7
x8
c2
x6
c2
Attach Panels Z and X using
Panels O1 UPSIDE DOWN.
Tighten Cam Locks and apply
Cam Covers.
Attach Panel G. Tighten Cam Locks and apply Cam
Covers.
Make sure Plate Casters are locked and turn the
cabinet over onto its wheels.
G
Part One: Cabinet Shell
Z
Z
X
X
O1
O1

Assembly InstructionsKiwi 8
6x35 x6
c1
x6
c2
Part One: Cabinet Shell
A1/A2
A1/A2
1.
3.
D
2.
1. Insert Panel D
(back)
NOTE: Panels A1 and A2 come pre-assembled with prein-
stalled hinges
2. Prep Panel A1/A2 with Cam Bolts as shown below.
3. Attach Panel A1/A2 to
Panels X, Z and O1 as
shown. Tighten Cam Locks
and apply Cam Covers.

Assembly InstructionsKiwi 9
x4
x4
s1
P-Brackets are optional. They work to help
stabilize the back panel of your cabinet. If
you choose not to use them, your cabinet
will still function as it should.
Measure approximately 8 inches from the top
and bottom of the cabinet. Slide P-Brackets
into the seam between Panel X and Panel
D, and Panel Z and Panel D. Attach with s1
Screws.
p
x1
x1
x1
x4
O
x2
s2
h2
h2
t2
t2
b
b
s2
Prep Panel O as shown below
Part One: Cabinet Shell
D

Assembly InstructionsKiwi 10
x4
s2
Attach Panel O to Panel Z with s2 Screws as illustrated below.
Part One: Cabinet Shell
Z
O
s2
h2

Assembly InstructionsKiwi 11
6x35 x12
c1
x4
c2
Attach side Panels K5 and K6 to drawer front Panel
K3. Tighten cams and apply covers. Repeat x3
Prep drawer front Panel K3 as shown above by installing 4
c1 Cam Bolts. Repeat x3
Slide drawer bottom Panel K11 into the grooves on
Panels K5, K6 and K3. Repeat x3
K3
K3
K5
K6
K5
K6
K11
Part Two: Drawers
K3
x3
x3 x3

Assembly InstructionsKiwi 12
Part Two: Drawers
To reach the pre-drilled screw holes on the sides of
Panels K5 and K6, you will need to tilt the drawer
runners.
Remove the front and back screws on the drawer
runners, leaving the middle screw installed. Pivot the
drawer runners to access screw holes as shown above.
Attach back Panel K4 using s3 Screws.
Realign drawer runner and replace screws on drawer
runner as shown below.
Our customer service agents are ready to help! Call
us at 1-800-533-7347, ext. 1.
3.5x35 Screw x4
s3
K3
K6
K5
K4

Assembly InstructionsKiwi 13
Slide drawer bottom Panel K11 into the grooves on
Panels K9, K10 and K7.
Prep drawer front Panel K7 as shown above by
installing 4 c1 Cam Bolts
K7
6x35 x4
c1
x4
c2
Attach side Panels K9 and K10 to drawer front
Panel K7. Tighten cams and apply covers.
K7
K9
K10
K9
K10
K11
K7
Part Two: Drawers

Assembly InstructionsKiwi 14
Part Two: Drawers
3.5x35 Screw x4
s3
K9
K10
K7
K8
Attach back Panel K8 using s3 Screws.
Fully extend the cabinet rails, align
drawer rails, and slide drawers into cad-
dy. Be sure that the silver ball bearing
pieces are positioned all the way to
the front of the rails.
TIP: Gently open and close the drawers
a few times to engage the Soft Close
mechanism.

Assembly InstructionsKiwi 15
6x50 Dowel Pin x66
d2
Part Three: Removable Peg Boards
Place Panel I Ironing Pad on top of Panel A1.
I
Handle x4
h1
Insert d2 Dowel Pins into
Panel K1. If you choose to
use glue in this step, note
that the dowels will not be
reconfigureable once glue
has set.
Attach h1 Handles to Panel
K1 using the bolts found
with the h1 Handles.
Repeat with the second
Panel K1 peg board.
x2
K1
d2
h1

SEW IN COMFORT. SEW LONGER.™
LIMITED LIFETIME WARRANTY
Kangaroo™ Sewing Furniture Limited Lifetime Warranty
WHAT THIS WARRANTY COVERS: Arrow Companies, LLC “Arrow” provides a Limited Lifetime Warranty
“Warranty” to the original purchaser of this product against defects in materials or workmanship of furniture
components. As used in this Warranty, “defect” means imperfections in components which substantially
impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Electrical and mechanical components of furniture are warrantied
for 5 years.
HOW TO GET SERVICE: Simply contact Arrow at 1-800-533-7347 or [e-mail]. When you
request Warranty service, you must also present proof of purchase documentation, which includes the
date of purchase (detailed receipt), and photos of the product. Arrow will replace any defective part (at
its sole option), excluding labor. Replacement parts will be warranted for only the remaining period of
the original Warranty.
Replacement parts will be shipped freight prepaid on any initial Warranty claim during first year of Warranty
only. Warranty applies only to defects confirmed by Arrow and will be replaced or repaired at Arrow’s
option. In the event parts are no longer available for a Warranty claim, customer may receive a brand new
cabinet at a price equal to 60% off the MSRP of a current comparable model.
WHAT’S NOT COVERED: There is no Warranty coverage for defects or conditions that result from the
failure to follow product assembly instructions, information or warnings, misuse or abuse, intentional
damage, fire, flood, alteration or modification of the product, or use of the product in a manner inconsistent
with its intended use, nor any condition resulting from incorrect or inadequate maintenance, cleaning,
care, or neglect, cuts or scratches, caster damage as a result of moving furniture fully loaded or with
locked casters, damage resulting from electrical surge or lightning, or use in commercial or education
environments. Kangaroo Sewing Furniture is designed for residential use only.
ARROW SHALL HAVE NO LIABILITY for ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND
and all such damages are EXCLUDED FROM THIS Warranty, such as loss of use, disassembly, transportation,
labor, or damage to property on or near the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion may not apply to you. The
Warranty cannot be transferred to subsequent owners or users of the product, and it shall be immediately
void in the event the product is resold, transferred, leased or rented to any third party or person other than
the original purchaser.
ADDITIONAL LIMITATIONS: THERE ARE NO OTHER WARRANTIES APPLICABLE TO THIS PRODUCT. Under
the laws of certain states, there may be no implied warranties from Arrow and all implied warranties,
INCLUDING ANY IMPLIED Warranty OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
are disclaimed where allowed by law. TO THE EXTENT ANY IMPLIED WARRANTIES ARE APPLICABLE, ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED Warranty OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THIS EXPRESS Warranty or
the minimum period allowed by law, whichever is shorter. Some states do not allow limitations on how long
an implied Warranty lasts, so the above limitation may not apply to you. This limited Warranty gives you
specific legal rights. This limited Warranty does not, in any way, affect the rights given to you by law.
REGISTER YOUR PRODUCT: Original purchaser should register the purchase online at www.ArrowSewing.com/Warranty.

SEW IN COMFORT. SEW LONGER.™
Height Adjustable Sewing Chair
Insert
10-21
Enhance your sewing experience with a custom
acrylic sewing insert! Custom acrylic sewing
inserts are designed to fill the gap between your
sewing machine and sewing cabinet’s lift opening
to create a flush, ergonomic surface for flat bed
sewing. To ensure a perfect fit, custom acrylic
sewing inserts are built specifically for your
sewing machine and sewing cabinet combination.
Say hello to happy wrists, straighter stitches,
and an elevated sewing experience!
Arrow’s #1 Rated Height Adjustable Sewing Chair
is a must have accessory for your dream sewing
room! Cute, comfortable and convenient - our
lovable sewing chairs feature vibrant sewing
themed patterns, 360 swivel access and lumbar
support for long hours at your workstation. Don’t
look now, but under every seat cushion is a hidden
storage compartment to store your notions and
patterns! Available in 10 colors to perfectly match
your sewing sanctuary!
Accessories to Complete Your Sewing Studio
Custom Insert Arrow Sewing Chairs
P.O. Box 410 Elkhorn, WI 53121
1-800-533-7347 Ext. 1
[e-mail]
www.ArrowSewing.com