Kangaroo K9605EL User manual

SEW IN COMFORT. SEW LONGER.™
ASSEMBLY INSTRUCTIONS
Outback
ITEM NO.: K9605EL Teak Electric Lift K9605XL Teak Hydraulic Lift
K9607EL Gray Electric Lift K9607XL Gray Hydraulic Lift
K9611EL Ash White Electric Lift K9611XL Ash White Hydraulic Lift
Assembly Instructions for XL Hydraulic Lift Models Only

Assembly InstructionsOutback 2
1. Read the instructions carefully before beginning the assembly process to ensure proper assembly
of this product. Please open and inspect the contents of box(es) to see that all parts and hardware
are included.
2. Tools Required
180°
Screw cam bolts flush as
illustrated.
Press cam into hole until flush with
surface. The arrow direction must
be in the direction of the hole.
Insert bolt through pre-drilled
hole in edge of panel.
Turn clockwise to lock cam with bolt.
General Assembly Guidelines
3. Understanding How the Cam Fastener Works
Tip: place a small bit of WD-40 or similar
lubricant into the pre-installed cam bolt
holes to help the cam bolts screw in better.
4. Glue provided is to secure wood dowels in place and is optional. If glue is used during assembly,
locate the appropriate hole for the dowel, place a small amount of glue in the hole and insert the
dowel. Wipe away excess glue immediately. It is not necessary to glue the other end of the dowel
when attaching to other parts.
Use and Care Your cabinet normally requires a minimum amount of maintenance; however, the
following points are worth noting:
Cleaning – To remove marks and enhance the surface, wipe with a gentle all-purpose cleanser. DO NOT
use ammonia-based, harsh chemicals or abrasive cleaning agents. Wipe dry immediately.
Electric and Hydraulic Lifts – Require annual lubrication with WD-40 or similar lubricant.
Phillips Screwdriver Hammer Electric Screwdriver
Torque set to 3-5

Assembly InstructionsOutback 3
Parts List: Panels
G
A
A2
A1
O1
O2
D
Y
Z
X
V1
V2
B
C
O4
Caddy parts are pictured on Page 5.
It is important to build the Caddy FIRST.
A3
ITEM DESCRIPTION QT Y. PACK.
Caddy Hardware Box 1 4 of 4
A4/A5 Caddy Top Panels 1 4 of 4
G1 Caddy Bottom Panel 1 4 of 4
D1 Caddy Back Panel 1 4 of 4
X1 Caddy Left Side 1 4 of 4
Z1 Caddy Right Side 1 4 of 4
O3 Caddy Thread Spool Holder Board 2 4 of 4
LCaddy Small Drawer Front 2 4 of 4
L1 Caddy Small Drawer Left Side 2 4 of 4
L2 Caddy Small Drawer Right Side 2 4 of 4
L3 Caddy Small Drawer Back 2 4 of 4
L4 Caddy Drawer Bottom 3 4 of 4
IIroning Board Panel 1 4 of 4
KCaddy Large Drawer Front 1 4 of 4
K1 Caddy Large Drawer Left Side 1 4 of 4
K2 Caddy Large Drawer Right Side 1 4 of 4
K3 Caddy Large Drawer Back 1 4 of 4
ITEM DESCRIPTION QTY. PACK
Main Cabinet Hardware Box 1 1 of 4
XLeft Panel 1 1 of 4
ZRight Panel 1 1 of 4
O1 Left Gate Leg Panel 1 1 of 4
O2 Right Gate Leg Panel 1 1 of 4
YCenter Panel 1 1 of 4
O4* Support Foot for Electric Lift Only 1 1 of 4
V1 Left Door Panel 1 2 of 4
V2 Right Door Panel 1 2 of 4
DBack Panel 1 2 of 4
A1 Quilt Leaf 1 2 of 4
A/B/C Top Panels 1 3 of 4
A3 Platform Cover Panel 1 3 of 4
GBottom Panel 1 3 of 4
Metal Bar 1 3 of 4
A2 Lift Panel 1 3 of 4

Assembly InstructionsOutback 4
Parts List: Hardware
TIP: Keep all the parts in their individually labeled bags. This will make finding parts easier as you assemble your cabinet.
6x35 Cam Bolt x26
c1
5⁄8“ Cam Cover x26
c2
8x30 Dowel Pin x26
d1
8x16 Fix Bolt x20
b1
4x20 Fix Bolt x4
b2
Handle x2
h
3.5x14 Screw x58 3x14 Screw x44 3.5x20 Screw x4 Alignment Pin x2
s5
s2
s4
s1
Butt Hinge x7 Flush Hinge x6
Lock x1 Magnet x2
Lock Plate x1 Catch Plate x2Key x2
h1
h2
L
m
Door Hook x2
d
Caster x3 Locking Plate Caster x5
t1
t2
Lift Rail
(Left) x1
Lift x1
Lift Rail
(Right) x1
Cam Lock
Pre-installed parts
Panel ConnectorCaster Bracket
c5
Snag Free Hinge
h4
Allen Wrench x1
a
14mm Wrench x1
r3
Door Plate x2
d3
3.5x30 Screw x5
s6
Metal Support Bar x1
Caddy parts are pictured on Page 5.
Accessories Hook x6
h4

Assembly InstructionsOutback 5
Caddy Panel and Hardware List
6x35 Cam Bolt x24 5⁄8“ Cam Cover x24 8x30 Dowel Pin x12
d1
3.5x35 Screw x12
c1
c2
s3
t4
Allen Wrench x1
a
8x16 Fix Bolt x16
b1
Locking Plate Caster x2
A4
A5
X1
D1
G1
Z1
L3
L1
L4
L2
L
K3
K2
K1
K
L4
x1
x2
8x80 Dowel Pin x62
d2
x2
Handle x4
h1
I
Caddy panels are listed on Page 3.
O3
t1
Plate Caster x2

Assembly InstructionsOutback 6
Part 1: Caddy
We can’t wait to get your brand new Outback Sewing Cabinet up and running! Please contact our Customer Service Team at 1-800-
533-7347, ext. 1 during normal business hours with any assembly related questions.
You will find all parts and panels for the Caddy in Box 1. It is important to build the caddy before building the main cabinet.

Assembly InstructionsOutback 7
Caddy Step 1: Base
6x35 Cam Bolt x4
c1
Locking Plate Caster x2
t4
8x16 Fix Bolt x16
b1
Allen Wrench x1
a
Insert Cam Bolts into pre-installed Cam Bolt Anchors.
Set Panel G1 aside.
G1
Attach t1 and t4 Casters with
b1 Bolts using Allen Wrench as
illustrated.
Lock casters and turn panel over.
G1
Plate Caster x2
t1
t4
t1
b1
c1

Assembly InstructionsOutback 8
Caddy Step 2: Sides and Back
Insert 4 Dowel Pins into the sides of Panel D1.
Insert 2 Cam Bolts into the top of Panel X1
Insert 4 Dowel Pins into the sides of Panel X1
Z1
X1
6x35 Cam Bolt x4
8x30 Dowel Pin x12
d1
c1
Insert 2 Cam Bolts into the top of Panel Z1
Insert 4 Dowel Pins into the sides of Panel Z1
D1

Assembly InstructionsOutback 9
Caddy Step 2: Sides and Back
5⁄8“ Cam Cover x4
c2
Insert Cam Bolts on Panels X1 and Z1 into Panel D1. Tighten
Cam Locks and cover with Cam Covers.
D1
Z1
X1

Assembly InstructionsOutback 10
Attach Panel G1 as shown. Tighten Cam Locks and cover with Cam Covers.
NOTE: Make sure the locking casters are at the front of the Caddy before attaching the sides and back.
G1
X1
D1
Z1
Caddy Step 3: Attaching the Base
5⁄8“ Cam Cover x4
c2

Assembly InstructionsOutback 11
A4
A5
Caddy Step 2: Top
6x35 Cam Bolt x4
c1
5⁄8“ Cam Cover x4
c2
Install Cam Bolts as illustrated below.
Lower Panel A4/A5 onto Panels
D1, X1 and Z1 as shown. Tight-
en Cam Locks and apply Cam
Covers.
A4
A5
D1
X1
Z1

Assembly InstructionsOutback 12
Caddy Step 3: Drawers
x2
x1
K3
K1
K2
L3
L1
L2
s3
s3
3.5x35 Screw x12
s3
Attach Panels L1 and L2 to Panel L3 using
s3 Screws as shown above.
Repeat for 2nd drawer.
Attach Panels K1 and K2 to Panel K3
using s3 Screws as shown above.

Assembly InstructionsOutback 13
Caddy Step 3: Drawers
L4
L3
L4
K3
K2
K1
L2
L1
x1 x2
Slide drawer bottom Panels L4 into grooves on Panels L1/L2/L3 and Panels K1/K2/K3 as shown above.

Assembly InstructionsOutback 14
Caddy Step 3: Drawers
6x35 Cam Bolt x12
c1
5⁄8“ Cam Cover x12
c2
x2
x1
x2
x1
Attach c1 Cam Bolts to Panels L (2) and K.
Attach drawer front Panel Lto drawer
side Panels L1 and L2 as shown.
Tighten cams and cover with c2 Cam
Covers.
Repeat with 2nd drawer.
Attach drawer front Panel Kto drawer
side Panels K1 and K2 as shown.
Tighten cams and cover with c2 Cam
Covers.
K
L
K
K1
K2
L
L1
L2

Assembly InstructionsOutback 15
Caddy Step 3: Drawers
Fully extend the cabinet drawer rails, align drawer
rails, and slide drawers into caddy.
Be sure that the silver ball bearing pieces
are positioned all the way to the front of the
rails.
TIP: Gently open and close the drawers a few
times to engage the Soft Close mechanism.
WARNING: CADDY IS PRONE TO TIPPING WHEN
NOT ATTACHED TO THE MAIN CABINET. Always
have your Caddy anchored to your cabinet to
prevent tipping (see page 31).

Assembly InstructionsOutback 16
Caddy Step 4: Thread Spool Boards
8x80 Dowel Pin x62
d2
Handle x4
h1
Insert d2 Dowel Pins into Panel O3. If you choose to use glue in this step, note
that the dowels will not be reconfigureable once glue has set.
Attach h1 Handles to Panel O3 using the bolts found with the h1 Handles.
O3
d2
h1
x2

Assembly InstructionsOutback 17
Part 2: Main Cabinet
Refer to the packing chart on Page 3 for panel locations.

Assembly InstructionsOutback 18
Main Cabinet Step 1: Base
Plate Caster x5
t2
8x16 Fix Bolt x20
b1
Attach Plate Casters to the underside of Panel Gwith Fix
Bolts.
Tighten with provided Allen Wrench.
Lock the Casters and flip Panel G over.
Allen Wrench x1
a
6x35 Cam Bolt x10
c1
G
G
Install Cam Bolts on Panel G.

Assembly InstructionsOutback 19
Main Cabinet Step 2: Back, Center and Side Panels
8x30 Dowel Pin x20
d1
6x35 Cam Bolt x6
c1
Install 2 Cam Bolts in Panel X.
Insert 4 Dowel Pins in Panel X.
Install 2 Cam Bolts in Panel Z.
Insert 4 Dowel Pins in Panel Z.
X
Z
D
Install 2 Cam Bolts in Panel D.
Insert 12 Dowel Pins in Panel Z.

Assembly InstructionsOutback 20
Lift Rail
(Right) x1
3.5x14 Screw x6
s1
Insert d1 Dowels into the edges of Panel Y.
Attach Lift Rail (left) to Panel Y with s1 Screws.
Attach Lift Rail (right) to Panel Z with s1 Screws.
Z
Lift Rail
(Left) x1
IMPORTANT: Spray a bit of WD-40 or similar lubricant onto a paper towel and wipe the lift rail down.
This is necessary in order for the lift to function smoothly, and must be repeated annually.
Y
8x30 Dowel Pin x6
d1
Main Cabinet Step 2: Back, Center and Side Panels