Kauber Blue Label XL User manual

w w w . k a u b e r . e u
-1-
PROJECTION SCREEN
INSTALLATION MANUAL
BLUE LABEL XL

w w w . k a u b e r . e u
-2-
Blue Label is a series of electrical projection screens with aluminum housings. Their timeless design
and a broad selection of projection screen materials make them the screen of choice for home cinema and
conference room applications. In the Tensioned version, the screen is additionally equipped with a set of
tensioners improving flatness of the projection surface.
IMPORTANT!!!
INSTALLATION AND APPLICATION GUIDELINES
1. The housing and lower beam of the screen are protected against mechanical damage with polyurethane
foam. Do not remove the main housing protection before step 4 and the lower beam protection before step
6 of this assembly and installation manual.
2. The screen shall be installed away from humidity and direct source of strong sunlight.
3. Use a soft damp cloth to clean the screen. Do not use active cleaning chemicals. Protect the screen
assembly from penetration of water or other liquids inside the housing. Carefully wipe the screen dry after
cleaning, to remove any moisture.
Content of the set:
Qty.
Projection screen
1
Mounting bracket for ceiling installation (flat)
2
Mounting bracket for wall installation (angle)
2
Ø14 rawlplug for wall installation
8
Ø10 rawlplug for ceiling installation
8
M6x12 screw
8
M6 washer
8
L-shaped screen locking and safety bar
4
Chain (screen installation aid)
2
Screen limit position adjustment key
1
Wall-mounted control switch panel (accessible for screens without built-in wireless
controller)
1

w w w . k a u b e r . e u
-3-
INSTALLATION
1. Within 20 cm from the edges of the housing, fit the mounting brackets to the wall or ceiling (see Figure
1). Dimensions of the housing are provided at the end of this manual, in the „Technical Specifications”
section.
Figure 1
2. Depending on the installation option, fit the wall brackets using the Ø14 rawlplugs provided in the kit
(Figure 2a) or the ceiling brackets using the Ø10 rawlplugs (Figure 2b).
NOTE! The rawlplugs and screws supplied in the installation kit can only be used for structural ceiling
materials (concrete, Suporex or other similar materials). Shall the screen be mounted on other types of
material, choose appropriate plugs and screws.
Wall installation
Figure 2a

w w w . k a u b e r . e u
-4-
Ceiling installation
Figure 2b
3. In case of wall installation, assemble the flat and angle brackets using the screws supplied in the
installation kit.
Figure 3

w w w . k a u b e r . e u
-5-
4. Fit the screen housing on the brackets. Use the chains to lift and hold the screen housing. Remove the
chains after installation.
Figure 4
5. The bracket mounting system is shown in the figures below. Fitment of the screen can be described in
three steps
:
Figure 5

w w w . k a u b e r . e u
-6-
STEP 1
Lift the screen housing all the way up, pushing it against the mounting brackets.
Figure 6
STEP 2
Slide the screen sideways, towards the bracket hooks.
Rys.7
STEP 3
Lower the screen housing to hang on the hooks.
Figure 8
NOTE!
Grooves for insertion of the
safety/locking bars

w w w . k a u b e r . e u
-7-
6. Lock the suspended screen housing using the safety/locking bars by sliding them in the groove between
the bracket and the housing. Figures 8, 9a and 9b show the insertion sequence and location.
Figure 9a
Figure 9b

w w w . k a u b e r . e u
-8-
7. Upon delivery, the screen is preset to the limit positions specified in the order. Shall the screen position
be incorrect (too low or too high), the end-positions can be adjusted using the special key provided in the
installation kit (Figure 10.).
NOTE! Only qualified persons may perform the end-position adjustments. All adjustments made shall be
the sole responsibility of the user. Non-qualified adjustment of the mechanical settings may cause damage
to the screen and shall void any guarantee claims.
Access to the end-position adjustment mechanism
Figure 10
8. In the case of screens equipped with a side tensioning mechanism, unroll the whole surface of the screen.
If necessary, adjust the tensioning force with an Allen key (screws on both sides of the lower bar).

w w w . k a u b e r . e u
-9-
ELECTRICAL CONNECTIONS
NOTE!
Only certified electricians shall be allowed to make the electrical connections of the screen.
Before installing the main housing of the screen, route the power supply cable to the installation point and then
connect it to the screen following wiring diagram A (Figure 11A) or wiring diagram Bin case of screens with
built-in wireless control modules (Figure 11B)..
.
WIRING DIAGRAM A
Figure 11A
WIRING DIAGRAM B (built-in wireless controller)
Figure 11B
Faza –Hot
Zerowy –Neutral
Uziemienie –Earthing
Czarny –Black
Brązowy – Brown
Niebieski –Blue
Żółto-zielony –Yellow/Green
Silnik ekranu –Screen drive motor
Przełącznik klawiszowy – Control
switch panel

w w w . k a u b e r . e u
-10-
Wiring of the control switch panel (provided in the kit)
(Control switch panel provided in the screen installation kits without wireless controller)

w w w . k a u b e r . e u
-11-
Wiring diagram of the screen control switch panel
Pin Description Color
L Hot (L) Brown
N Neutral (N) Blue
X Earthing Yellow/Green
1 Black
2 Brown

w w w . k a u b e r . e u
-12-
TECHNICAL SPECIFICATIONS
Housing dimensions:
BLUE LABEL XL
A- Screen width
B- Screen height
F = A + 96 mm
J = A + 40 mm
K = 50 mm
BLUE LABEL XL + BLACK FRAME
A- Active screen width
B- Active screen height
C = A + 100 mm
D = B + 100 mm
F = A + 196 mm
J = A + 140 mm
K = 50 mm
BLUE LABEL XL + BLACK FRAME + BLACK
TOP
A- Active screen width
B- Active screen height
C = A + 100 mm
D = B + 50 mm + height of the black strip
F = A + 196 mm
J = A + 140 mm
K = 50 mm

w w w . k a u b e r . e u
-13-
BLUE LABEL XL + TENSIONERS
A- Active screen width
B- Active screen height
C = A + 100 mm
D = B + 100 mm
F = A + 326 mm
J = A + 270 mm
K = 50 mm
BLUE LABEL XL + TENSIONERS + BLACK
TOP
A- Active screen width
B- Active screen height
C = A + 100 mm
D = B + 50 mm + height of the black strip
F = A + 326 mm
J = A + 270 mm
K = 50 mm
Technical specification:
Supply: 230V, 50Hz
Power rating: 140 W –screen without wireless control system
160W –screen with built-in wireless control system

w w w . k a u b e r . e u
-14-
Thank you for choosing a KAUBER screen
Feel free to purchase other products of the KAUBER brand