FLEXIBLE TUBING to HARD PIPING INSTALLATION
INSTRUCTIONS - for MOTOR/PUMP PART# 055173
(CONTINUED)
page 2
hardPiping057122.qxd
10/09
Operation #2 Re-Assembly
Your Kit Includes (items with * may not be included):
Item Part # Qty Description
A --------- - ------------------------
*B 056990 1 Pipe Nipple 3/8 NPT 1-1/2 SS-304
C 056907 1 Bracket Ass’y Haight Baker Pump
D 020101 8 Nut 5/16 Hex Head Serrated Flang
E 017142 4 Screw 5/16-18 x 3/4 Hex Head
F 015227 2 Nut 1/4” Acorn S/S
G 004611 4 Screw #10 x 3/8 Sheet Metal Pan HD.
*I 037672 A/R Sealant Locktite 262 (.017 oz.)
J 056765 8 Washer Flat 7/16” ID x 1.00 OD x .078 THK.
K 017481 4 Screw 5/16 -18 x 1-3/4 Hex HD SS
L X 1 Reinforcement Bracket
M 015158 2 Acorn Nut 5/16-18 SS
N 052733 2 Washer 11/32 ID x 3/4 OD
O 000290 2 Washer, Lock 5/16” Spilt
Pump Mount Cover
GSee Note #4
Motor Mount Housing Assembly
Filter Tub Assembly
Filter Cart Frame Assembly
L
See Note #2
See Note #1
Filter Tub Connected
Side View
Bottom View
Mount Reinforcement
Bracket as Shown
Bolts
Must Be
Flush Not
Tight
C
K&D Bolts Only
for Models 20”
and 24” See
Note #2
J&I See
Note #5
Filter Tub
Pull Rod
See Note #3
K,M,N,O F&I See
Note #3 B
D&E
Support Filter Tub As
Shown to Remove Any
Play Between Tub and
Filter Cart.
Item ‘C’ Detail
Filter Tub Disconnected
View B
See Note A
View A
Table or Bench
2-5/8”
Note A Dimensions
9-5/16” for 14” Filter
11-3/8” for 18” Filter
12-3/8” for 20” Filter
14-3/8” for 24” Filter
Notes:
1. Remove filter tub from motor/pump housing assembly and
set aside. On 18, 20 and 24 models only, remove pipe nipple
3/8” NPT x 1” and discard. Replace with pipe nipple 3/8”
NPT x 1-1/2” (item B). See view A for proper dimensions
from back of sump to front of quick connect. On 14” filter tub,
see view A for proper dimesions from back of sump to front
of quick disconnect. Place the filter tub into the filter cart
assembly. Release the filter tub away from the pump housing
as shown in side view. Turn the entire assembly upside down
as shown in view B. This step is critical to insure proper
alignment between the motor housing quick connect and the
filter tub quick connect. Use table or bench, making sure the
motor/pump housing is off of the table/bench.
CAUTION: IF FILTER ASSEMBLY IS PLACED UPSIDE DOWN
ON A TABLE OR BENCH, MAKE SURE UNIT IS SECURE, SO
AS NOT TO SLIDE OFF TABLE/BENCH.
2. Slide item C into position to connect the compression fitting
on the pump’s 90° fitting. DO NOT TIGHTEN COMPRES-
SION FITTING AT
THIS TIME. Attach item C, to the pump housing with items D and
E. DO NOT TIGHTEN COMPLETELY AT THIS TIME. Play must be
present for proper alignment of pump housing connect and filter
tub quick connect. Slide the filter tub assembly forwarduntil the
quick connects are engaged. Tighten items D and E completely.
Tighten compression on item C. Remove (2) bolts and washers “K”
and add reinforcement bracket “L.” Use longer (2) bolts provided
and discard old ones. For 20 and 24 models, add
items D and K to reinforcement bracket and
tighten until snug on motor mount housing
assembly (See Bottom View).
3. Attach filter tub pull rod handle using item
F and I.
4. Attach the pump mount covers using item G.
5. Inspect for spacers between casters and filter
cart assembly. If none are present, remove
casters and place item J (2) on the casters
threaded stem and reassemble using existing
fasteners and item I.
6. Carefully turn filter assembly to the upright
position. Release the filter tub pull rod and
check for proper disconnect. Reconnect the
filter tub to the motor mount housing using
handles. If the assemblies do not connect
properly, it will be necessary to verify notes
above were followed correctly.
7. Fill filter tub with oil per users manual, cycle oil
to check for leaks at fittings, correct if needed.
L
