Keba KeContact P30 x-series Instruction sheet

KeContact
P30 x-series
Charging station
Configuration manual V 4.04
Translation of the original manual

Document:V 4.04 / Document No.: 105802
Filename: KeContactP30x-series_konfen.pdf
Pages: 37
© KEBA
Specifications are subject to change due to further technical developments. Details presented may be
subject to correction.
All rights reserved.
KEBA AG Headquarters: Gewerbepark Urfahr, 4041 Linz, Austria, Phone: [phone],
Fax: [phone], [email protected]
For information about our subsidiaries please look at www.keba.com.

P30 x-series Table of contents
Configuration manual V4.04 3
© KEBA
Table of contents
1 Introduction ................................................................................................................ 5
1.1 Representation of safety instructions............................................................... 6
1.2 Purpose of the document................................................................................. 7
1.3 Requirements................................................................................................... 7
1.4 Guarantee ........................................................................................................ 7
1.5 Notes on this document ................................................................................... 8
1.5.1 Contents of the document.................................................................. 8
1.5.2 Not contained in this document ......................................................... 8
1.6 Further documentation..................................................................................... 9
2 System overview ........................................................................................................ 10
2.1 Network interfaces ........................................................................................... 10
2.1.1 LAN .................................................................................................... 11
2.1.2 WLAN (optional) ................................................................................ 12
2.1.3 WLAN Access Point (Hotspot) (optional)........................................... 13
2.1.4 GSM (optional)................................................................................... 13
2.2 Design of a local charging network (master/slave) .......................................... 14
2.2.1 Displays and signals .......................................................................... 14
2.2.2 Direct connection of master and slave............................................... 15
2.2.3 Connection via router or switch ......................................................... 15
2.2.4 Ports for communication in the charging network.............................. 16
3 Configuration.............................................................................................................. 17
3.1 Connection panel ............................................................................................. 17
3.2 DIP switch settings........................................................................................... 17
3.3 Configuration via web interface........................................................................ 18
3.3.1 Main menu ......................................................................................... 20
3.3.2 User menu ......................................................................................... 23
3.4 Enabling the DHCP server............................................................................... 23
3.5 Configuration in series via USB stick ............................................................... 23
4 Functions .................................................................................................................... 25
4.1 Load management in the local charging network ............................................ 25
4.1.1 Equal allocation mode ....................................................................... 25
4.1.2 Current limiting................................................................................... 25
4.2 RFID authorization ........................................................................................... 26
4.2.1 Authorization modes .......................................................................... 26
4.2.2 Displays and signals .......................................................................... 27

P30 x-seriesTable of contents
Configuration manual V4.04
4
© KEBA
4.2.3 RFID authorization without OCPP backend connection .................... 27
4.2.4 RFID authorization with OCPP backend connection ......................... 29
4.2.5 Start charging process with RFID authorization ................................ 29
4.3 OCPP backend ................................................................................................ 30
4.4 UDP interface................................................................................................... 31
4.5 Integration of external meters .......................................................................... 31
4.5.1 Connection......................................................................................... 33
4.5.2 Supported meters .............................................................................. 33
4.5.3 Settings.............................................................................................. 34
5 Maintenance................................................................................................................ 35
5.1 Diagnosis and troubleshooting......................................................................... 35
5.2 Software update............................................................................................... 35
5.2.1 Software update via web interface..................................................... 36
5.2.2 Software update via USB stick .......................................................... 36
5.2.3 Software update via OCPP backend ................................................. 36
Index ............................................................................................................................ 37

P30 x-series Introduction
Configuration manual V4.04 5
© KEBA
1 Introduction
This document refers to the following devices:
P30 x-series with software version 1.7 or a later version of the software
The device variant can be determined by the product designation on the type
plate. The software version can be read out via the web interface. For more
information, see the "operating instructions".
The pictured devices used in this manual are visual examples. The figures
and explanations contained in this manual refer to a typical device design.
The devices used by you may differ in their appearance.

P30 x-seriesIntroduction
Configuration manual V4.04
6
© KEBA
1.1 Representation of safety instructions
At various points in this manual, you will see notes and precautionary warn-
ings regarding possible hazards. The symbols used have the following
meaning:
DANGER!
indicates an imminently hazardous situation, which will result in death or se-
rious bodily injury if the corresponding precautions are not taken.
WARNING!
indicates a potentially hazardous situation, which can result in death or seri-
ous bodily injury if the corresponding precautions are not taken.
CAUTION!
means that if the corresponding safety measures are not taken, a potentially
hazardous situation can occur that may result in slight bodily injury.
Caution
means that damage to property can occur if the corresponding safety mea-
sures are not taken.
ESD
This symbol reminds you of the possible consequences of touching electro-
statically sensitive components.
Information
Identifies practical tips and useful information. No information that warns
about potentially dangerous or harmful functions is contained.

P30 x-series Introduction
Configuration manual V4.04 7
© KEBA
1.2 Purpose of the document
This document describes the configuration of the advanced features of P30
x-series after it has been installed. This includes, among other things, the
description of the settings in the web interface.
This document is an extension to the supplied manuals of P30 x-series.
You must comply with all instructions and safety instructions in the
supplied manuals!
1.3 Requirements
This document contains information for persons with the following require-
ments:
Target group Required knowledge and abilities
Electrician
Person who, due to his or her special training, expertise and experi-
ence as well as knowledge of current standards, is able to assess
the work performed and the possible hazards.
Knowledge of:
● current valid safety information,
● the mode of operation of the charging station,
● the displays and operating elements of the charging station,
● basics of network technology,
● basics of IT,
● diagnostic options,
● systematic fault analysis and rectification,
● the setting options on the charging station.
1.4 Guarantee
Only the maintenance work expressly permitted by KEBA may be performed.
Any other manipulations to the device will also result in loss of warranty.
WARNING!
Danger due to electric shock and fire hazard!
After opening the front part, product safety can no longer be guaranteed.
Only the covers described in the instructions may be opened. If one of the
covers is sealed by a lead seal, it is not permitted to be opened by unautho-
rized persons. If the lead seal is broken, the device loses its specific suitabil-
ity and may no longer be put into operation due to the resulting incorrect
marking.

P30 x-seriesIntroduction
Configuration manual V4.04
8
© KEBA
Fig.1-1: Screws on front part
The front part 1 may not be opened. Opening the front part (4 Torx screws)
will break the warranty seal and void the warranty. For a warranty claim,
there is a duty of proof of the customer that the defect – which led to the de-
fect of the device – already existed at the time of delivery. If the warranty
seal is broken, this proof can no longer be provided, whereby the warranty
claim expires.
A device with broken warranty seals or removed lead seals may no longer
be put into operation. The necessary steps for replacement or repair of the
charging station by the specialist dealer or service partner must be initiated.
1.5 Notes on this document
The manual is part of the product. It is to be retained over the entire life cycle
of the product and should be forwarded to any subsequent owners or users
of the product.
The instructions contained in this manual must be followed precisely. Failure
to do so could result in the creation of potential sources of danger or the dis-
abling of safety devices. Apart from the safety instructions given in this man-
ual, the safety precautions and accident prevention measures appropriate to
the situation in question must also be observed.
1.5.1 Contents of the document
● Configuration of the advanced features of P30 x-series
1.5.2 Not contained in this document
● Commissioning and deinstallation of the charging station
● Operating behavior of the charging station
● Operation of the charging station

P30 x-series Introduction
Configuration manual V4.04 9
© KEBA
1.6 Further documentation
Manuals and additional information are available on the KEBA website:
www.keba.com/en/emobility/service-support/downloads/Downloads
Designation Target group
Operating instructions ● End customer
● Electrician
Installation manual ● Electrician
USB Configuration Guide
● Programmer
● Electrician
● Service technician
UDP Programmers Guide ● Programmer
FAQ
● End customer
● Electrician
● Service technician

P30 x-seriesSystem overview
Configuration manual V4.04
10
© KEBA
2 System overview
With P30 x-series, several charging stations can be interconnected in the
form of a master/slave network. This makes charging with an intelligent load
management possible. In addition, a connection to a higher-level OCPP
backend can take place. The charging station is equipped with different net-
work interfaces for these functions.
Fig.2-2: Example network setup
1 ... Local charging network 2 ... Router/Switch
3 ... Master charging station (x-series) 4 ... Slave charging station (c-series)
5 ... Higher-level network/Internet 6 ... OCPP backend
Only P30 x-series, can be operated as master charging stations; only P20/
P30 c-series can be operated as slave charging stations.
The following chapters describe which network interfaces P30 x-series (mas-
ter charging station) provides and how to set up a master/slave network.
2.1 Network interfaces
P30 x-series provides the following network interfaces (e.g. for connection to
an OCPP backend, ...):
● LAN
● WLAN (optional)
● WLAN access point (optional)
● GSM (optional)
Slave charging stations can only be connected via LAN to P30 x-series
(master charging station).

P30 x-series System overview
Configuration manual V4.04 11
© KEBA
2.1.1 LAN
P30 x-series can be connected to a router via the integrated LAN interface.
The router provides a connection to an OCPP backend over the Internet.
1 ... P30 x-series 2 ... Router
3 ... Internet 4 ... OCPP backend
Connection: Ethernet1-Anschluss (LSA+®)
Via the LAN interface, P30 x-series can also be connected to other charging
stations, whereby a charging network can be realized.
Information
The Ethernet2 connection X3 (RJ45) is for diagnose purposes (debugging)
only and may not be used to connect to a network.
The Ethernet1 connection X4 (LSA+®) and the Ethernet2 connection X3
(RJ45) are connected in parallel on the PCB and can not be used at the
same time! The connection that is not used must be unplugged from the
charging station.

P30 x-seriesSystem overview
Configuration manual V4.04
12
© KEBA
2.1.2 WLAN (optional)
P30 x-series can be connected to a router via the integrated WLAN inter-
face. If the router is connected to the Internet, a connection to an OCPP
backend can be made.
1 ... P30 x-series 2 ... Router
3 ... Internet 4 ... OCPP backend
The technical data of the WLAN module can be found in the "Installation
Manual".
Information
Only a charging station that is operated as a single charging station can be
connected to the router via WLAN. A charging station that is part of a
charging network (master/slave network) must always be connected to the
router via LAN.

P30 x-series System overview
Configuration manual V4.04 13
© KEBA
2.1.3 WLAN Access Point (Hotspot) (optional)
P30 x-series can be connected to a mobile device via the integrated WLAN
access point. With the mobile device, the web interface can be easily ac-
cessed and the configuration of the charging station can be performed.
1 ... P30 x-series
The access data and the IP address of the WLAN access point are listed on
the configuration label. The configuration label is in a pouch which is en-
closed with the mounting material.
The following steps are necessary to perform the configuration via a mobile
device:
1) Connect a mobile device to the WLAN access point.
2) Access the IP address of the WLAN access point in a web browser on
the mobile device.
3) Perform configuration via the web interface, see 3.3 Configuration via
web interface.
2.1.4 GSM (optional)
Certain device variants have a GSM module. P30 x-series with GSM can
connect to an OCPP backend over the cellular network. The mobile commu-
nications provider may charge additional fees (depending on the tariff) for
running data transmissions.
1 ... P30 x-series 2 ... OCPP backend

P30 x-seriesSystem overview
Configuration manual V4.04
14
© KEBA
For the connection to an external OCPP backend via GSM, a SIM card must
be installed during commissioning. In addition, GSM must be activated as
connection to the OCPP backend and the access data of the mobile service
provider must be set in the configuration (web interface).
The commissioning of the GSM module is described in the "Installation Man-
ual". The technical data of the GSM interface and the SIM card can also be
found in the "Installation Manual".
2.2 Design of a local charging network (master/slave)
A local charging network includes one P30 x-series as master and up to 15
c-series (P20 and/or P30) as slaves.
Depending on the number of slave charging stations, the design of a local
charging network is implemented differently:
●1 slave charging station: Direct connection
The slave charging station is connected directly to the master charging
station.
●Multiple slave charging stations: Connection via router or switch
The slave charging stations are connected to the master charging station
via a router or switch.
To enable communication between master and slave charging stations, the
charging stations must be configured in the web interface, see 3 Configura-
tion.
2.2.1 Displays and signals
The display on the front of the charging station provides information about
which communication connection is established.
Display Description
blue | blue | blue | blue
Communication is possible throughout the network.
The master charging station and the OCPP backend are reach-
able.
blue | blue | blue | -
Communication between master and slave charging stations is
possible.
The OCPP backend is not reachable or missing.
- | blue | blue | -
Communication between master and slave charging stations is
not possible.
The OCPP backend is not reachable.

P30 x-series System overview
Configuration manual V4.04 15
© KEBA
2.2.2 Direct connection of master and slave
A single slave charging station can be connected directly to the master
charging station via LAN.
Fig.2-3: Direct connection of master and slave
1 ... P30 x-series (master) 2 ... P20/P30 c-series (slave)
In this case, the master charging station must be configured as a DHCP
server. The IP address is then assigned to the slave charging station by the
master charging station.
2.2.3 Connection via router or switch
If there are multiple slave charging stations, these must be connected to the
master charging station via a router or switch. The connection of the charg-
ing station to the router/switch is made via LAN
Fig.2-4: Connection via router or switch
1 ... Router/Switch 2 ... P30 x-series (master)
3 ... P20/P30 c-series (slave)

P30 x-seriesSystem overview
Configuration manual V4.04
16
© KEBA
Using a router
In a network connection using a router, the router automatically provides the
functionality of a DHCP server in most cases.
Information
If the IP addresses are assigned externally (for example, by routers with ac-
tivated DHCP server), the IP addresses must not be in the following range:
192.168.25.xxx
Using a switch
For a network connection using a switch, the master charging station must
be configured as a DHCP server. The IP addresses are then assigned by
the master charging station.
2.2.4 Ports for communication in the charging network
For the correct communication in the charging network, the ports below must
be enabled network-internally.
Information
If necessary, contact your network administrator to enable the ports.
Port Protocol Definition Description
49153 TCP Within the network Socket of the charging station
15118 TCP Within the network Link connection between the charg-
ing stations (SDP)
15118 UDP Within the network Link connection between the charg-
ing stations (SDP)
68 TCP Within the network Transfer of the software update
(Bootps)
68 UDP Within the network Transfer of the software update
(Bootps)
67 TCP Within the network Transfer of the software update
(Bootps)
67 UDP Within the network Transfer of the software update
(Bootps)

P30 x-series Configuration
Configuration manual V4.04 17
© KEBA
3 Configuration
This chapter describes the necessary configuration for the correct operation
of the charging stations. The following steps are necessary for this:
● Set the DIP switch on the charging station
● Configuration (via the web interface or via USB stick)
Depending on the network configuration, activation of the DHCP server on
the master charging station may be necessary.
3.1 Connection panel
In the connection panel of the charging station are important interfaces and
controls for the configuration of the charging station. To access, the housing
cover and the connection panel cover must be removed. The description of
removing the covers and the connection panel can be found in the "Installa-
tion Manual".
3.2 DIP switch settings
This DIP switch setting must be made for each master and slave charging
station to enable charging station communication.
Caution
Possible damage to the DIP switches!
The DIP switches are rocker switches and not slider switches. The DIP
switches must be pressed and must never be slid.
ON/OFF position of the rocker switches
The illustration shows the position of the rocker switches for the setting ON
and OFF
The DIP switches are located under the connection panel cover. The follow-
ing figure shows only the affected DIP switches, others are not shown. The
following setting must be made on the DIP switch DSW2:

P30 x-seriesConfiguration
Configuration manual V4.04
18
© KEBA
Activation of communication - DSW2.5
Function Figure
Activation of communication
Information
Changes to the DIP switch settings only become effective after a restart of
the charging station!
To restart, press the "Service button" until the first beep (approx. 1 second)
or switch off the charging station for a short time via the line circuit breaker.
3.3 Configuration via web interface
The necessary settings (main menu "Configuration") for the communication
of the charging station are configured in the web interface. The configuration
for the entire charging network is done via the master charging station.
A network connection is required to access the web interface of the master
charging station. The network connection can be made via LAN, WLAN,
WLAN access point or GSM (e.g. with PC or mobile device).
The web interface of the master charging station can be accessed by enter-
ing the IP address of the master charging station in a web browser.
The IP address of the master charging station is determined differently de-
pending on the connection type.
WLAN access point The IP address of the WLAN access point is printed on the con-
figuration label.
Router with integrated
DHCP server
The charging station automatically receives an IP address via
the DHCP server of the router. The IP address is displayed on
the charging station display when the charging station is
(re)started. The IP address can also be determined via the
router.
Master charging station
with local DHCP server
The local DHCP server has been activated for the master
charging station, which automatically gives the master charging
station the following IP address: 192.168.42.1
The DHCP server of the charging station is deactivated in the
delivery state and can be activated via the configuration in the
web interface.
A login is required to use the web interface.

P30 x-series Configuration
Configuration manual V4.04 19
© KEBA
The login data for the first login in the web interface is printed on the configu-
ration label. The configuration label is in a pouch which is enclosed with the
mounting material. For security reasons, change the password after the ini-
tial login.
Fig.3-5: Configuration label
After successful login, the start page of the web interface opens.
Fig.3-6: Web interface start page
1 ... Main menu 2 ... User menu
The following chapters provide an overview of the possibilities of the web in-
terface. A detailed description of the individual configuration options can be
found directly next to the respective configuration entry.

P30 x-seriesConfiguration
Configuration manual V4.04
20
© KEBA
3.3.1 Main menu
The main menu is divided into the following areas:
● Status
● System
● Configuration
Status
The area shows basic information about the configured charging stations
(such as: serial number, IP address, operating state ...). Clicking on the re-
spective IP address opens the "Information Center" in a new browser win-
dow. It displays charge information such as total power, charge session
power, power, voltage, current, state, and basic log. The scope of the dis-
played information is variant-dependent.
System
The area offers the following options:
● Software-Update
● GSM Signal Test
● Logging
● Restart System
Software-Update
The currently installed software versions are displayed. A software update
can also be performed here.
GSM Signal Test
Here, the connection to the set GSM network can be tested.
Logging
Different log contents of the master charging station are displayed.
Restart System
The master charging station can be restarted using this button.
Configuration
The configuration of the charging stations is carried out in this area.
Information
The DIP switch settings are independent of the web interface configuration
and can not be overwritten by software.