KEBCO 00.F4.010-3009 User manual

7/2003
PM.F4.01B-K102
KEB Memory Operator Memory Operator
BETRIEBSANLEITUNG
INSTRUCTION MANUAL

D 2

GB 3
1. General................................................................................GB 4
1.1 Product Description ............................................................. GB 4
2. Memory Operator ...............................................................GB 5
2.1 Operation as Digital Operator .............................................. GB 5
2.2 OperationasMemory Operator ............................................ GB 6
2.2.1 Upload ......................................................................................................GB 7
2.2.2 Download ..................................................................................................GB 7
2.2.3 Abort andFault Acknowledgement ...........................................................GB 7
3. Special Functions ..............................................................GB 8
3.1 Interlock of the Mode FU_OP............................................... GB 8
3.2 Changing of the Baud Rate.................................................. GB 8
3.3 Drive Mode in the Memory-Operator .................................... GB 9
3.4 Software Date ...................................................................... GB 9
4. Error Messages................................................................GB 10
Table of Contents

GB 4
00.F4.010-3009
1. General This manual as well as the hardware and software are developments of
the Karl E. Brinkmann GmbH. Errors and omissions excepted! The Karl
E. Brinkmann GmbH prepared the documentation, software and
hardware to the best of its knowledge, but no guarantee is given that the
specificationswillbringthe user theefficiencyaimed at.The KarlE.Brink-
mann GmbH reserves the right to change the specifications without
obligation. All rights reserved!
KEB Antriebstechnik develops, manufactures and distributes static
frequency inverters worldwide in the industrial power range. Within the
scope of automization, systems are needed which are more powerful
and flexible.With this in mind KEB developed a programming unit which
makes it possible to program several inverters quickly and without
internetworking. Parameter lists can be permanently stored in the
programming unit, so they can be immediately retrieved when needed.
1.1 Product
Description
TheMemory Operator
- Can upload saved parameter lists from F4/S4 units
- Can download saved parameter lists
- IsdownwardcompatibletotheDigital-Operator(Exception:Drive-Mode)
- Can be directly connected to the F4/S4 units
Memory Operator

GB 5
Operation as
Digital Operator
see section 2.1
Operation as
Memory Operator
see section 2.2
2. Memory
Operator
The Digital Operator is the Standard Operator without interface in the
KEBCOMBIVERTF4/S4.The MemoryOperatorisdownwardcompatible
and can be used for normal operation except for one restriction.
Duringthe operation ofthe MemoryOperator the Drive Mode
inCOMBIVERT F4/S4 maynot beactivated,because thekey
assignment overlaps with the memory mode.
2.1 Operation as
Digital Operator
wait until the display or LED is off
Insert Operator and switch on the unit
Switch off COMBIVERT
According to the baud
rate of the Operator the
display is shown for 5
Seconds.
with 9600 Baud with 19200 Baud
or
! also see 3.2 Changing of the Baudrate!
When the display switches the unit is ready for operation
Operation as Digital Operator

GB 6
In this operating mode the parameter lists can
- be read from the inverter (Mode: FU_OP) (Upload)
- be written to the inverter (Mode: OP_FU) (Download)
Hold for approx. 5 sec. ➥changes operating mode
Operationas Memory Operator
Switch off COMBIVERT
wait until the display or LED is off
Wait until display switches
with 9600 Baud with 19200 Baud
or
! also see 3.2 Changing of the Baud Rate!
Insert Operator and switch on the unit
Error Message Meaning
Display with locked Mode FU_OP.
The Mode FU_OP (Upload) can be locked, to make sure that
the data stored in the operator can not be overwritten.
see also section 3.1 Lock of the Mode FU_OP
Frequency inverter or servo controller was not recognized by
theoperator.PossibleCause:
- Connectionpin broken/missing
- Baudrateof theinverter/ Servo-controller notinaccordance
with the baud rate of the operator
see 3.2 Change of the baud rate
To avoid problems for further operations, please pay attention to the
following error messages!
! Further error messages see section 4 error messages!
ENTER
F/R
FUNC.
SPEED
+
2.2 Operation as
Memory Operator
Accordingto thebaudrate
of the inverter the display
is shown 5 seconds

GB 7
FUNC.
SPEED
START
ENTER
F/R
ENTER
F/R
FUNC.
SPEED
START
ENTER
F/R
ENTER
F/R
FUNC.
SPEED
➡➡➡➡
➡
+
➡➡➡➡
➡
+
Operating mode: download
Operating mode: upload
➥ Changes to the operating mode: upload
➥ Starts the upload process
Upload
operating
Upload completed
➥Confirms the upload
Hold for approx. 5 sec. ➥switches to normal operation
when Display „no_Lo“
see section 3.1
Lock Mode FU_OP
Operating mode: download
➥ Starts the download process
Download
operating
Download completed
➥Confirms the Download
Hold for approx. 5 sec. ➥switches to normal operation
2.2.3Abort and Fault
knowledgement Withthe „Stop“-keya read-orwriteprocess canbe interrupted.Theerror
message Err.1 is displayed. With the „Enter“-key the error message is
accepted and the operator changes into the selected operating mode.
Data,transfered beforeinterruptionare writteninthe selectedtarget unit.
A parameter list, which is interrupted during the transfer to the operator
or COMBICARD displays at transmission (e.g.: mode OP-FU) the error
message Err.6, because the list does not include all parameters.
2.2.1 Upload
2.2.2 Download

GB 8
START
STOP
➥➥
➥
START
STOP
➥➥
➥
The mode FU_OP (Upload) can be locked, to make sure that the data
stored in the operator can not be overwritten.The status is displayed by
pressing the POWER-ON button and the „FUNC.-key“ simultaneously.
Lock Mode FU_OP:
Enable Mode FU_OP:
enablemode
FU_OP(Upload)
locked the
modeFU_OP
goes back into
normaloperation
Lockedmode
FU_OP(Upload)
goes back into
normaloperation
releaseof
modeFU_OP
FUNC.
SPEED
➥➥
FUNC.
SPEED
➥➥
Press
Switch on
Inverter
Press
Switch on
Inverter
START ➥START
STOP
➥➥
➥
➥
START ➥START
STOP
➥➥
➥
➥
Toadjustthe baud rateofthe operatortothebaud rateatFU,the operator
can operate with 9600 baud or with 19200 baud. The actual adjusted
baud rate is displayed by pressing the POWER-ON button and the
„START-key“ simultaneously.
Increase Baud Rate:
Decrease Baud rate:
Press
Switch on
Inverter 9600 Baud
increasebaudrate
to19200 baud
goes back into
normaloperation
Press
Switch on
Inverter 19200 Baud
goes back into
normaloperation
decreasebaud ra-
te to 9600 baud
After changing of the baud rate the display of the operator goes into nor-
mal operation.
3.2 Changing of the
Baud Rate
3. Special functions
3.1 Lock Mode FU_OP

GB 9
Toswitchaninverter/servowithMemory-Operatorintothe memorymode
do the following:
ENTER
F/R +
FUNC.
SPEED
press
MemoryMode
Inverter/Servo in Drive-Mode
To return to the Drive-Mode, do the following:
ENTER
F/R +
FUNC.
SPEED
press
Inverter/Servo is in the CP-Mode
Inverter/Servo in Drive-Mode
Enter the Drive-Mode password in CP.0
Drive-Mode
The Drive-Mode can not be exited when inverter type
45 (agree with F4-SV1.0) is used
If the STOP-key is pressed when the programmer is switched on, the
software date of the memory operator is shown.
Day Month Year
3.3 Drive-Mode in the
Memory-Operator
3.4 Software Date

GB 10
Memory capacity is not sufficient to
read in parameters.
(In mode FU-OP)
Unitisnotsuitedfor data transmission
withthe memory operator.
Parameters have not been saved
completely in the operator memory
(RAM).
During download into memory and
errors message occurred (Err.1....5).
Thus, not all parameters could be
saved.
The connected inverter’s address
does not correspond to the inverter
address saved in the memory.
- Clear error message by pressing
the ‘ENTER’-key →inverter’s
address will not be changed
- By pressing the ‘START’-key →the
error is cleared and the addresses
in the memory operator are down-
loaded.
Downloadto theinverterwasstopped
(With Mode OP_FU) The inverter was not in state „noP“ during writing parameter Fr.01 →
open control release and start
„download“ again.
Saved (e.g. type 45) and connected
(e.g. type 46) inverter do not
correspond.
All type numbers can be displayed
(In mode OP_FU)
- Clear message by pressing the
‘ENTER’ -key →download is
stopped.
- Clear message by pressing the
‘START’-key →download
continues.This functionis usede.g.
to change inverter-software-
versions, to transfer old download
lists onto the new software.
(Beispiel)
4. Error Messages
Display Description Cause / Remedy
Frequencyinverter orservocontroller
was not recognized by the operator Connectionpinbroken/missing; Baud rate notcorrectadjusted; Operatoror
controller defective
Upload unpossible - Data of the
inverter cannot be load in the
operator
Mode FU_OP (UPLOAD) is locked.
(see3.1)
Selectedoperation canceled byuser. “STOP” -key was pressed while
display was flashing
Duringanactiveoperation(e.g.download)
the connected inverter or servo is no
longer recognized by the operator.
Connection pin broken or missing,
transmission interrupted, frequency
inverter/servo controller is switched
off.