kenall ENVIROPRO EPC Series User manual

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin. It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
1
INSTALLATION INSTRUCTIONS
EPC_F-4492_08318
Luminaires for Food Processing Applications
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions
should always be followed, including the following:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED. DISCONNECT POWER TO ALL CIRCUITS
BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH
ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT
TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS
AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.
SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE
FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING
ORIENTATION, OR MOUNTING RESTRICTIONS.
SAVE THESE INSTRUCTIONS
OVERVIEW
EPC SERIES
ENVIROPRO™
EPC Series xtures are designed to be suspended, pendant or surface mounted. Supplied stainless steel mounting
straps are fully adjustable along the length and provide 90 degree (45 degrees each side) rotational aiming.
Fixtures are pre-wired with a 72" oil and water resistant outdoor cable. Connection to electrical service must be
made using approved water tight connector or plug and receptacle.
SUSPENDED MOUNTING
Installation
1: Remove spade screw, washer and sealing washer.
Remove the end cap from the end without the
cable.
2: Remove the tube and install lamps.
3: Replace the tube and end cap. Replace the sealing
washer, washer and secure by tightening the spade
screw.
4: Wrap the two supplied stainless steel straps around
the tube and secure by pulling the tab to lock into
the slot on the other side.
5: Hang the xture by attaching to user supplied chain
or cables. Adjust the mounting straps along the
length of the xture as needed.
6: Connect the cable to the appropriate electrical
service. Black wire to supply, white wire to neutral
and green wire to ground.

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United States with more than 50% of the component cost of US origin. It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
2
INSTALLATION INSTRUCTIONS
EPC_F-4492_08318
SURFACE MOUNTING
Installation
1: Remove spade screw, washer and sealing washer.
Remove the end cap from the end without the cable.
2: Remove the tube and install lamps.
3: Replace the tube and end cap. Replace the sealing
washer, washer and secure by tightening the spade
screw.
4: Wrap the two supplied stainless steel straps around the
tube and secure by pulling the tab to lock into the slot
on the other side.
5: Attach the two supplied stainless steel brackets to the
ceiling or structure with user supplied hardware.
6: Mount the xture straps
to the brackets using
the supplied screws,
washers and nuts.
Be sure no threads
are exposed after
tightening. Any exposed
threads must be covered
using appropriate user
supplied cap.
7: Connect the cable to the appropriate electrical service.
Black wire to supply, white wire to neutral and green
wire to ground.
PENDANT MOUNTING
Mounting straps are available for either 3/8 or 1/2
pendants. These should be specied when ordering.
Check for proper straps before starting installation.
Installation
1: Remove spade screw, washer and sealing washer.
Remove the end cap from the end without the
cable.
2: Remove the tube and install lamps.
3: Replace the tube and end cap. Replace the sealing
washer, washer and secure by tightening the spade
screw.
4: Wrap the two supplied stainless steel straps around
the tube and secure by pulling the tab to lock into
the slot on the other side.
5: Mount xture by attaching straps to pendants,
supplied by user.
6: Connect the cable to the appropriate electrical
service. Black wire to supply, white wire to neutral
and green wire to ground.
RE-LAMPING
Before starting any servicing, turn off the power to the
xture and allow the lamps to cool.
1: To replace the lamps, remove end cap, Step 1 above.
2: Replace lamps and reinstall tube, end cap and
hardware.
For warranty information visit www.kenall.com/Resources/Certied-Performance-Warranties
For technical assistance, call 1-800-4KENALL (1-800-453-6255).
WARRANTY
CUSTOMER SERVICE