Kenall High bay max hbm series User manual

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

HBM_F-4938_090418

Luminaires for High Bay Applications

LED HIGH BAY MAX™

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions

should always be followed, including the following:

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE

APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH

THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND

THE HAZARDS INVOLVED. DISCONNECT POWER TO ALL CIRCUITS

BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH

ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT

TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS

AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.

SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE

FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING

ORIENTATION, OR MOUNTING RESTRICTIONS.

SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

HBM SERIES

I.Pendant Mount Installation

1. Remove cover by removing nut from xture.

Nut and washer

Cover

Hub

3. Fasten the hub to the stem.

Cover

2. Slide the nut, washer and cover over the stem

(stem supplied by others).

Nut

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

HBM_F-4938_090418

4. Hook loop bracket to xture hanger bracket.

5. Make electrical connection, then slide cover down.

Fixture

Bracket

Loop

Bracket

6. Fasten nut tightly over hub for water-tight seal.

Nut

III. Trunnion Kit Installation

1. Remove the two (2) nuts holding the cover. 2. Remove the four (4) bolts holding trunnion

bracket together.

Trunnion

Bracket

NOTE: Slide Adjustment Screw to level the xture.

Adjustment

Screw

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

HBM_F-4938_090418

3. Fasten the top bracket to the surface, using two (2)

5/16" bolts (supplied by others).

4. Attach 3/4" sealed hub (supplied by others)

and conduit.

5. Make electrical connections. 6. Fasten cover down.

Sealed hub

(by others)

7. Reattach the four (4) bolts to the trunnion bracket.

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

HBM_F-4938_090418

1. Remove screws and lift cover of xture.

Loop safety cable under center support.

2. Send straight end through loop end of the

safety cable.

3. Replace cover and secure the cable to the

super-structure.

II. Safety Cable Option

LOOP HANGER INSTALLATION – HL

(ATTACHED AT FACTORY)

Aircraft cable (not included) is recommended for attaching the xture structural to the upper structural.

SAFETY RECOMMENDATION

1. Wire cord leads to power supply leads using

connectors suitable for the gauge and number of

wires being used. Black xture lead connects to

the supply conductor, white xture lead connects

to the neutral supply conductor, and the grounding

wire must be connected to a suitable ground.

2. Hang luminaire by attaching to user supplied chain

or cables.

3. Connect power cord.

4. As a safety recommendation, an additional aircraft

cable (not included) should be used to attach the

loop hanger and supporting structure.

LOOP HANGER

CORD WITH

QUICK-DISCONNECT

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

HBM_F-4938_090418

Optic Alignment Key

Fixture align arrow

aimed in this position

will yield these patterns.

(See xture label for

type ordered)

Type 2

Aisle

Type 5

Square

Type 5

Narrow

Type 4

Type 3

Fixture Align Arrow

Label Detail

Top View

Detail A

Scale 2:1

INSTALLATION INSTRUCTIONS

F-5406_073014

BIRD GUARD INSTALLATION

1. Bird Guard lays on top of casting.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

always be followed, including the following:

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

CE PRODUIT DOIT ÊTRE INSTALLÉ EN CONFORMITÉ AVEC LE CODE DE

L'INSTALLATION PAR UNE PERSONNE QUI connaît BIEN LA CONSTRUCTION ET

LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS.

DISCONNECT POWER TO ALL CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN

ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT

CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS AND

LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE. SUPPLEMENTAL

INSTRUCTIONS MAY BE LOCATED ON THE FIXTURE, IN ADDITION TO THIS

INSTRUCTION SHEET, REGARDING ORIENTATION, OR MOUNTING RESTRICTIONS.

SAVE THESE INSTRUCTIONS

Pendant Mount

Trunnion Kit

PENDANT MOUNT & TRUNNION KIT

(For Trunnion Kit use slots)

2. Attach both sides with (4) screws provided.

Luminaires for High Bay Applications

LED HIGH BAY MAX™

HBM SERIES

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents