Kendal Lighting AC-22656 User manual

(MODEL NUMBER:AC-22656)

1

1. Securely attach the hanger bracket to the outlet box
by washers and screws suppplied. Connect white
wire from ceiling to white wire from receiver with
wire nut. Connect black wire from ceiling to
black wire from receiver with wire nut. (see Fig.5)
2. Carefully lift the fan and seat the down rod ball
assembly on the hanger bracket. Be sure the
groove in the ball is lined up with tab on the
hanger bracket . Do not pinch wires between the
ball and down rod assembly and hanger bracket
(see Fig.6)
3. Install the safety cable into the building structure.
(see Fig.7)
Putting Your Fan Together
Hanging Your Ceiling Fan
1. Remove the hairpin clip & washer from the clevis
pin and remove clevis pin from down rod. (see
Fig.1)
2. Insert the down rod through the center opening in
the canopy,coupling cover and route the motor
leads through the hanger ball/downrod assembly.
Align the clevis pin holes in the downrod with the
holes in the motor coupling. The clevis pin must
pass through the holes in the motor coupling and
the downrod. Place the washer onto the clevis pin
and install the hairpin clip making sure to push
straight leg of the hairpin clip through the hole
near hanger ball to make sure the clevis pin is
properly installed(see Fig.2)
3. Reinstall the 2 set screws in the motor coupling and
securely tighten set screws against the down rod
assembly.
DOWNROD
ASSEMBLY
WASHER
CLEVIS PIN
HAIR PIN CLIP
DOWNROD ASSEMBLY
CANOPY HOLE COVER
COUPLING COVER
WASHER
SCREW
FAN BODY
CLEVIS PIN
HAIR PIN CLIP
MOTOR COUPLING
CANOPY
CENTER BAND
BLADE
BLADE
WASHER
SCREW
CENTER BAND
OUTLET BOX
HANGER BRACKET
FLAT WASHER
STAR WASHER
SPRING WASHER
SCREW
HANGER BACKET
DOWNROD
RECEIVER
WHITE WIRE
BLACK
WIRE
WHITE WIRE
RECEIVER
BLACK
WIRE
Attached each blade assembly to the center band using
the blade screws and blade washers.Tighten them
securely.(see Fig.3& 4)
Caution: To reduce the risk of personal injury.
Do not bend the blade when installing, balancing
or cleaning the fan. Do not insert foreign objects
between rotating fan blades.

Wiring Your Ceiling Fan
Caution: To avoid possible electrical shock,
be sure electricity is turned off at the main
fuse box before wiring.
1. If you are not sure that the electrical box is
grounded,contact a licensed electrician for
advice.It must be grounded for safe operation.
2. Connect the white wire from receiver to the
white wire from fan with wire nut .Connect
the black wire from receiver to the black
wire from fan with wire nut.Connect the
blue wire from receiver to the blue wire
from fan with wire nut. Connect the green
wire from ceiling,and green wire from hanger
bracket with green wire from downrod
ball with wire nut.(see Fig.8)
3.Remove one of screws and loosen the other
screw from the hanger bracket. (see Fig.9)
4. Mount the canopy on the hanger bracket
and tighten the screws.(see Fig.10)
5. Place the canopy hole cover over the screws
and twist the cover to tighten. (see Fig.11)
CEILING
SATETY CABLE
WASHER
WASHER
SCREW
DOWNROD
HANGER BRACKET
OUTLET BOX
RECEIVER
GREEN WIRE
BLACK WIRE
WHITE WIRE
BLUE WIRE
FAN BODY
HANGER BRACKET
SCREW
HANGER BRACKET
CANOPY
SCREW
SCREW
CANOPY
CANOPY HOLE COVER

1. Remove 3 screws on light kit adapter, (See
Fig.12)
2.Lift the light kit plate onto the light kit adapter
and align the three holes on light kit plate with
the light kit adapter.Tighten back the 3 removed
screws.()
3.Remove 3 screws on light kit plate.(see Fig.14)
4.Plug together light kit wires from fan to light kit
wires from LED light(see Fig.15)
5.Tighten the light kit by using the 3 screws
removed in step 3 (see Fig.16)
6. Attach the PC shade by locating tabs in light
kit with grooves on the light shade and twist
clockwise until tight (see Fig.17)
Fan Airflow Direction
Slide the reverse switch to right or left to obtain
opposite direction of airflow. (See Fig.18)
See Fig 13
Installing The Light Kit
FIG.18
MOTOR
LIGHT KIT ADAPTER
SCREW
FAN BODY
LIGHT KIT
PLATE SCREW
BOTTOM
HOUSING
SCREW
LIGHT KIT
PLATE PIN
LED LIGHT
PLUG
LIGHT KIT
PLATE
SCREW
LED
LIGHT
LIGHT KIT
PLATE
TAB
INDENTATION
PC SHAPE
FAN BODY
REVERSE SWITCH

TNA18010301

4.CONNECTINGTHERECEIVER(FIG.2)
5.INSTALLINGTHEWIRELESSWALLTRANSMITTER
.OPERATINGTHETRANSMITTER
8
Usethewirenutsprovidedandmakeelectricalconnectionsasfollows:
a.ConnectGreenwirefromfantotheBarecopper(ground)fromjunctionbox.
b.ConnectBlackwire(ACINL)fromtheReceivertotheBlackwirefromthe
junctionbox.
c.ConnectWhitewire(ACINN)fromtheReceivertotheWhitewirefromjunctionbox.
d.ConnectBlackwire(TOMOTORL)fromtheReceivertotheBlackwirefromfan.
e.ConnectWhitewire(TOMOTORN)fromtheReceivertotheWhitewirefromfan.
f.ConnectBluewire(FORLIGHT)fromtheReceivertotheBluewirefromfan.
gAfterwiresareconnected,carefullytuckthemintothejunctionbox.
h.LaytheblackantennawireontopoftheReceiverandinsertintothemountingbracket.
i.Reinstallthecanopyontothemountingbracket.
.
#8
Removethesmallpanelonthefrontofthetransmitterandinsertthebatteryprovided.Make
surethe +” -”sighiscorrect.(FIG.3)
NOTE:Use1x12V(23A)battery.Ifnotusingforlongperiodoftime,removebatterytoprevent
damagetotransmitter.
a. HI”button:thisbuttonusedtoselectthefanathighspeed.
b. MED”button:thisbuttonusedtoselectthefanatmediumspeed.
c. LOW button:thisbuttonusedtoselectthefanatlowspeed.
d. OFF”Thisbuttonwillturnthefanoff.
e. LIGHT”Thisbuttonwillturnthelightonoroffandwillalsocontrolthebrightnesssetting.
Pressandreleasethebuttonandthelightwillturnonoroff.Pressandholdthebuttonfor
thedesiredbrightness.Thelightwillcyclecontinuouslybetweenbrightanddimsettingsas
longasthebuttonishelddown.Thelightkeyhasautoresume,itwillstayatthesame
brightnessaslasttimewhenitwasturnedoff.
f.Memoryfunction
Ifyouturnoffthefanorlightbywallcontrol,itwillmemorizeandrecoverautomaticallyto
lasttime’sfanspeedandlightbrightnesswhenturnedonnexttime.
g.Lighton/offanddimmerselect.
Thereisadipswithintheplate.(fig1),thisswithusedtoselectthelightmode,Ifthisswith
select D”,Thelightinthedimmingmode.Ifthisswitchselect ON”,thelightinthe ON/OFF”
mode.
.
a
b.
c.
.
6.INSTALLINGTHEBATTERYINTOTHETRANSMITTER(FIG.4)
7
(FIG.3)
RECEIVERPROTECTIVEFUNCTIONS
Removetheexistingwallplateandswitch.Besuretocompletetheelectricalcircuitwithin
thejunctionboxby-passingwallcontrol.Connectblacktoblack,whitetowhite,greento
green.Carefullypushwiresintotheoutletbox.
Attachwallcontrolunittooutletboxusingthetwo-32screwsprovided.
Attachwallplatetotheswitchcontrolfrontusingthetwosmallscrewsprovided.
a.Overloadprotection(currentlimit)-Thedevicelimitsthemaximumcurrentoutputfromthe
receiver/drivewhenthefanorlightloadisincreasedabnormally.Thefanwillshutoffifover
lamped.
CEILINGFANWALLTRANSMITTERCONTROLLER
WARNING!SHUTOFFTHEPOWERWITHFUSEORCIRCUITBREAKER.
1.SAFETYPRECAUTIONS:
WARNING:HIGHVOLTAGE: Disconnecttheelectricpowersourcebyremoving
fuseorswitchingoffcircuitbreakers.
Donotusewithsolidstatefans.
Electricalwiringmustmeetalllocalandnationalelectricalcoderequirements.
Electricalsourceandfanmustbe115/120volt,60Hz.Maximumfanmotor1A,Maximum
lightwatts:60WLEDonly.
Householdelectricpowercancauseseriousinjuryordeath.
a.Turnthepowerofftoyourceilingfan.
b.Returnpowertothereceiver.
NOTE:AftertheACpowerison,donotpressanyotherbuttononthewalltransmitter
beforepressingthe SET”button(inthesmallplate),doingsowillcausethe
proceduretofail.(Fig.1)
c.Within60secondsofturningthefan’sACpoweron,Pressandholdthetransmitter’s
SET”buttonfor3seconds.
d.Oncethereceiverhasdetectedthesetfrenquency,thelightofyourfanifapplicable
willblinktwice.(Thereisnoindicationifyourfanisnotequippedwithalight)
e.Thereceiverhasnowlearnthefrequencywiththewalltransmitter.Aftercompleting
thestepsabove,youshouldbeabletooperatetheceilingfanandlight.Ifthefanis
notrespondingtothetransmitter,Pleaseturnthepowerofftothereceiver,andrepeat
theprocess.
2. FREQUENCYINTERFERENCE.
3.INSTALLINGTHERECEIVER
a.Removetheceilingfancanopyfromthemountingbracket.
bDisconnecttheexistingwiringbetweenceilingfanandthejunctionbox..
NOTE: Thisdevicecomplieswithpart15oftheFCCrules.Operationissubject
tothefollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference;
(2)Thisdevicemustacceptanyinterferencereceived,including
interferencethatmaycauseundesiredoperation.
FIG.3
FIG.4
12V(23A)
Battery
12V
HI
LOW
OFF
LIGHT
TOMOTORL
TOMOTORN
FIG.2
FIG.1
AC8-LED-DCW-2160414
SET D
ON
MED
HI
LOW
OFF
LIGHT
MED
12V
SET D
ON
SET
D
ON
TOMOTORL
TOMOTORN
HZ