Kenmore 75251 24,500 User manual

Owner's Manual
Manual del
®
I
Model, Modelo 580. 75251
V
Distribut_ by Sears, Roebuck and Co., Hoffman Estates, IL 60179
www.sears.com

TABLE OF CONTENTS ........................2
WARRANTY ..............................................2
SAFETY ..................................................... 3
Important Safety Instructions ...................... 3
ELECTRICAL REQUIREMENTS .......4
INSTALLING THE POWER CORD ....4
INSTALLATION ........................................5
Installation Requirements ......................... 5
Installation ................................................ 6
How to Install ............................................ 6
Removal from Window ................................. 8
OPERATION .............................................9
How and Why ........................................... 9
Normal Sounds ........................................ 9
Capacity and Running Time ..................... 9
Features ................................................. 10
Using the Air Conditioner ....................... 10
Display ................................................... 11
Remote Control ...................................... 12
MAINTENANCE .....................................13
Air Filter Cleaning ................................... 13
Air Conditioner Cleaning ........................ 13
How to Remove the Front Grille .................. 13
How to Replace the Front Grille .................. 13
TROU B LES HOOTI NG .........................14
Before Calling for Service ...................... 14
ESPANOL ................................................15
MASTER PROTECTION
AGREEMENTS ......................................31
SERVICE NUMBERS ............ Back Cover
FULL ONE YEAR WARRANTY ON
ROOM AIR CONDITIONER
For one year from the date of purchase, when this
air conditioner is operated and maintained for
normal room cooling according to the instructions in
this owner's manual, Sears will repair this air
conditioner, free of charge, if defective in material or
workmanship.
FULL FIVE-YEAR WARRANTY ON
SEALED REFRIGERATION SYSTEM
For five years from the date of purchase, when this
air conditioner is operated and maintained for
normal room cooling according to the instructions in
this owner's manual, Sears will repair the sealed
refrigeration system (consisting of refrigerant,
connecting tubing, and compressor), free of charge,
if defective in material or workmanship.
WARRANTY SERVICE IS AVAILABLE BY
CONTACTING SEARS SERVICE AT
1-800-4-MY-HOME ®.
Warranty coverage applies only to air conditioners
used for non-commercial, private household
purposes.
This warranty applies only while this product is in
use in the United States.
This warranty gives you specific legal rights, and
you may also have other right which vary from state
to state.
Distributed by Sears, Roebuck and
Co., Hoffman Estates, IL 60179
-2-

IMPORTANT SAFETY INSTRUCTIONS
The safety instructions below will tell you how to use your room air conditioner to avoid harm to yourself or
damage to your ROOM AIR CONDITIONER.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance. Read product labels for flammability and
other warnings.
PREVENT ACCIDENTS
To reduce the risk of fire, electrical shock, or injury
to persons when using your air conditioner, follow
basic precautions, including the following:
• Be sure the electrical service is adequate for the
model you have chosen.
• If the air conditioner is to be installed in a window,
you will probably want to clean both sides of the
glass first. If the window is a triple-track type with a
screen panel included, you may want to remove
the screen completely before installation.
• Be sure the air conditioner has been securely and
correctly installed according to the separate
installation instructions provided with this manual.
Save this manual and installation instructions for
possible future use in removing or reinstalling this
unit.
• Use gloves when handling the air conditioner.
Be careful to avoid cuts from sharp metal fins on
front and rear coils.
ELECTRICAL INFORMATION
The complete electrical rating of your new room air
conditioner is stated on the serial plate. Refer to the
rating when checking the electrical requirements.
• Be sure the air conditioner is properly grounded.
To minimize shock and fire hazards, proper
grounding is important. The power cord is
equipped with a three-prong grounding plug for
protection against shock hazards.
• Your air conditioner must be plugged into in a
properly grounded wall receptacle. If the wall
receptacle you intend to use is not adequately
grounded or protected by a time delay fuse or
circuit breaker, have a qualified electrician install
the proper receptacle.
• Do not run air conditioner with a protective
covering. This could result in mechanical damage
within the air conditioner.
• Do not use an extension cord or an adapter
plug.
_ Avoid fire hazard or electric shock.
Do not use an extension cord or an adapter plug.
Do not remove any prong from the power cord.
3-prong
grounding
plug
Reset_
"_ Ground
Power_ t prong
supply /f
cord II
--3-prong
grounding
type wall
receptacle
ENERGY SAVING IDEAS
• The capacity of the room air conditioner must fit
the room size for efficient and satisfactory
operation.
• Install the room air conditioner on the shady side
of your home. A window that faces north is best
because it is shaded most of the day.
• Do not block air conditioner flow inside with blinds,
curtains, or furniture, or outside with shrubs,
enclosures, or other buildings.
• Close the floor and wall registers and the fireplace
damper so cool air does not escape up the
chimney or into the duct work.
• Keep blinds and drapes in other windows closed
during the sunniest part of the day.
• Clean the air filter as recommended in the
MAINTENANCE section of this manual.
• Proper insulation and weather stripping in your
home will help keep warm air out and cool air in.
• External house shading with trees, plants or
awnings will help reduce the air conditioner's work
load.
Operate heat producing appliances such as
ranges, washers, dryers, and dishwashers during
the coolest part of the day.
-3-

OBSERVEALL LOCAL CODES AND ORDINANCES,
DO NOT_UNDER ANY CIRCUMSTANCE& REMOVE
THE POWER SUPPLY CORD GROUND PRONG.
ELECTRICAL GROUND iS REQUIRED ON THIS
APPLIANCE.
For230/208 volt 60 Hz, AC only, 15A fused and
properly grounded dectrica] supply is required. A time
delay fuse or time delay circuit breaker is
recommended Use a dedicated circuit, sewing only
this appliance_
DO NOT USE AN E_ENSION CORD.
115V_ 230V_
i,
RECOMMENDED GROUNDING M_HOD
Foryourpersona]safety,thisapCance must_ grounded
This app]ian_ hasa powersupply cordwith a 3-prong
groundingplug.To minimizepossibleshockhazard,the
®rd mustbe pluggedintoa matinggroundingtype wall
receptade andgroundedin acoord_ce withthe National
ElectricalCode(ANS[CNFPA70} latesteditionandall local
codes and ordinals. If a matingwallreceptade is not
available, _isthe personalres_nsibility and obiigalionof
the customerto havea properlygrounded3-prongwali
rece)tade instail_ bya qualifiedd_dciaq.
Power _rd may includea current interrupter
device. Atest _d reset button isprovided on the
#ug case. The device shodd be tested on a
periodicbasis byfirst pressingthe TEST button
_d thenthe RESETbutton.Ifthe TESTbu_ton
doesnottrip or ifthe RESETbuttonwill notstay
engaged, discontinueuseofthe airconditionerand
contacta qualified servicet_hn[cian
NOTE: The shape may be different accordhg to its mo_].
Use Wall Receptacle Power Supply
St_ds_d 125V,
3-wire grounding
receptacle rated
15A, 125V AC Use 15AMP time
delay fuse or 15 AMP,
Standard 250V, citcuil b[eaker,
3-wire grounding
r_placle ral_]
15A, 250V AC
Standard 250V,
3-wire grounding Use 20 AMP time
r÷_placle raled deiay fuse or 20 AMP,
20A, 250V AC c _cuit breaker,
Electrical Shock Hazard
Plug into a grounded 3 prong outbt.
Do not remove ground prong
Do not use an adapter,
Do not use an extension cor&
Failure to follow the_ instructions c_ result in
death, fire, or electrical sh_k.
You can choose between two methods bdow according to your window sill shape and preference.
USING SLIT "A"
Fasten the stopper using 2 screw holes, and lead
out the power _rd through siit "A'_
_f
-4-
USING SLIT "B"
Fasten the stopper using left _rew hole, and rotate
properly to lead the _wer cord out through silt "B".

INSTALLATION REQUIREMENTS
Your air conditioner will install into standard double
hung windows with actual clear opening widths of
29 to 41 inches (737mm to 1041mm) (FIG. 1)
Lower sash must open sufficiently to albw a clear
vertical opening of 19 inches (483mm). Side louvers
and the rear of the air conditioner must have clear
air space to allow enough airflow through the
_ndenser for heat removal. The rear of the unit
must be outdoors, not inside a buiiding or garage.
19"rain. Inner
Interiorwall
Exterior
FIG, 1
ELECTRICAL SERVICE
Check your available electrical service. The power
supply available must be the same as that shown on
the unit n_eplate (found on right: side of cabinet).
AH mode_s are equipped with a 3-prong service plug
to provide proper service and safe positive
grounding_ Do not change plug in any way, Do not
use an adapter plug. If your present wall outlet does
not match your plug, call a qualified electrician to
make the necessary corrections.
SAVE CARTON and this OWNER'S MANUAL for
future reference. The carton is the best way to store
unit during winter or when not in use.
To avoid risk of personal injury, property damage,
or product damage due to the weight of this
device and sharp edges that may be exposed:
• Air _nditioners covered in this manual pose an
excessive weight hazard. Two or more people
are ne_ed to move and install the unit.
To prevent injury or strain, use proper li_ing and
carrying techniques when moving unit.
•Carefully inspect location where air _nditioner
will be installS. Be sure it will support the
weight of the unit over an extended peri_ of
time.
• Handle air _nditioner with care. Wear
protective gloves whenever lifting or car_ing the
unit. AVOID the sharp metal fins of front and
rear coils.
• Make sure air conditioner does not fali during
installation.
INSTALLATION HARDWARE
AB C D E N
F G H I J K
FIG. 2
ITEM NAME OF PARTS Q'TY
A SIDE CURTAIN 2
B SUPPORT BRACKET 2
C SILL BRACKET 2
D LOCK NUT 4
E SCREW: 25/64" 11
F SCREW: 13/16" 7
G SCREW: 9/16" 5
H M-SCREW 2
I CARRIAGE BOLT 2
J FOAM SEAL 1
K FOAM STRIP 1
L WINDOWLOCKINGBRACKET 1
M DRAIN PiPE 1
N WASHER 1
REQUIRED TOOLS:
•Tight Fi_ing gloves
• Standard screwdriver
• Phillips screwdriver
•Pliers
• Sharp knife
°3/8-incho_n end wrenchor adjustablewrench
•1/4-inch hex socket and ratchet
•Tape measure
° Electric drill
° 1/4-inch drill bit
-5-

Pick a location which will allow you to blow the cold
air into the area you want. Windows used for
installation must be strong enough to support:the
weight of the air conditioner. Good installation with
special attention to the proper position of the unit
will lessen the chance that service will be needed,
When cooling more than one room, installation
location is very important. To cool your rooms, cold
air must be blown from the air conditioner in a
straight path.
L_tly it is adviced to save the shpping carton for
future storage of the unit.
HOW TO INSTALL
If the air conditioner is bilked by a storm
window frame, see step 16 on page 8 before
b_inning to install.
_ Rernove the which fasten the cabinet
screws at
the back and side of the unit. Save side screws.
Discard back screws,
FIG. 3
_ Slide the unit out of the cabinet by gripping the
base pan handle and pull forward while bracing the
cabinet.
FIG. 4
Cut the FOAM SEAL (ITEM J) to fit the
underside of the window sash. Peel off the backing
and attach the FOAM SEAL as shown in Fig, 5,
Sash
FIG. 5
D Insertthe sidecurtains(_TEMA) intothe upperguide
and bwer gui@ on eachsi@ ofthe airconditionerca_net.
Fastenthe curtainsto the unRwith_rews (ITEME).
ITEME FIG. 6
_O_n the window. Marka line on thecenter of the
windowinnersi& Looselyattach thesill bracket(iTEM C)
to thesupport bracket(ITEMB) using thecarriage bolt
(iTEM i) and the Iocknut (iTEM D).
ITEM
ITEM I
_ Attach the sill bracket to the windowsill using the
screws (ITEM F). Carefully place the cabinet on the
window inner sill and align the center ofthe cabinet
front with the center line marked on the window inner
sill.
jMachine screw<!TEMH)
d [l_k nut {ITEMD)
andlocknut ITEMF
\
Silibracket FIG. 8
W Using the M-screw (ITEM H) and the I_k nut
(iTEM D}, atta@ the sup_rt bracket to the cabinet:
track hole, Use the first track hole as shown. Tighten
the carriage bolt and the Iod_nut. _ surethe cabinet
slants downward 1/4"from level,
CAUTION: Do not drill a hole in the base pan. The unit
is designed to operate with approximately 1/2" of water
in base pan.
Cabinet
OUTOOOR FIG. 9
-6-

_PuH the bottom window sash down behind the
upper guide until they meet,
NOTE:
• Do not pull the window sash down so tightly that the
movement of sliders is restricted, Attach the cabinet
to the window inner sill by drMng the screws 0TEM F)
through the cabinet into window innersill.
• The c_inet should be installed with a very slight ti_t
downward by 1/4" from ]eve],
Windowsash
_TEMF FIG, 10
_ Expand side curtains to fill opening.
Attach each side curt:_n to the window sash using 4
screws (_TEM G) (F_G, 1i)
• _nnect a drain elbow of 9/16" inside diameter to
the drain pipe,
• _nnect a drain hose of 9/16" inside diameter to the
drain elbow. (Drain hose is not supplied.)
Drain
pipe
FIG. 13
e_bow eMbow Drain
hose
_ Slide the air conditioner intothe cabinet. (FIG. 14)
CAUTION: For security purposes, reinstall side
screws that were removed in step I.
ITEM G
_] Attach the window locking bracket (ITEM L) with
a screw (ITEM G). See FIG. 12.
ITEM G
FIG. 12
a] DRAINAGE
A drain hole is provide, at the rear of the air
conditbner unit. Refer to the drain method below::
• Remove the hole wbber from the basepan.
_Cut the,foam strip (_TEMK) to the proper _ength
and inse_ between the upper window sash and the
lower window sash.. (FIG. 15)
FiG. 15
_ Adjust the vent before the decorative front is
attached, (FIG, 16)
Straighten the lever, as shown. Pull down part @to
align with part C_
!'%ili
F_G, 16
-7=

_FRONT INSTALLATION
Install the front grille(packed separately) onto the
cabinet as foNows:
• Hook upper tabs of front gritle into slots on the
cabinet top. (FIG. 17)
• Push front griIWs tips towards the cabinet in order
to snap side tabs into the cabinet, (FIG, 17)
• Open the inlet grille. (FIG. 18)
• Install the screw (_TEM E) through the front grille.
(FIG. 18)
• Close inlet grille, (FIG, t9)
Front Installation FiG. 17
_EM E
Front Installation FIG. 18
Front Installation FIG. 19
IF AIR CONDITIONER IS BLOCKED BY
STORM WINDOW FRAME
• If storm window presents interference, fasten a 2"
wide wood strip to the inner window s]l! across the full
width of the sill. The wood strip should be thick
enough to raise the height of the window sill so that
the unit can be installed without interference from the
the storm window frame. See FIG. 20.
Top dwood strip should be approximately 3/4"
higher than the storm window frame to help
condensation to drain properly to the outside,
• _nstal_a _nd w_d strip (approximately6" long by
11/2"wide and samethickr_ss asfirst strip) in thecenter
ofthe outersill flush a_inst: the back ofthe inner sill,
Screwthe Window I_king bracketsintothis strip.
This will raisethe,Window locking bracket as shown
in FIG 20,
WOODSTRIP MOUNTED
ON TOP OF INNER SILl,, 3/4
CLEARANCE
SILL LOCKIt@ BPACKEO,'
WOODSTRIP
FORWINDOW
LOCK!NGBRACKED
WINDOW
FRAME
SiLL
OUTSlOE FIG, 20
REMOVAL FROM WINDOW
• Turn off and un#ug the air conditJonero
•Removethe front grille.See HOW TO REMOVETHE
FRONTGRILLE.Referto _ge 13.
• Undrew the sidescrewsthat you installedin Step 15,
• Slidetie air condiflo_r outof the cabinet.
BE CAREFULNOT TODROP IT. Holdonto it firmlythe
who_eway slidingitold, Onceremoved,set it safetyout
of the way,
• Removethe Window locking bracketfrom window
frameand the sashsea! from betweenthewindows,
° Unscrewthe sidecurtainsfromthe windowframe, Fold
them backto the sidesof thecabinet.
•Removescrews attachingcabinetto inner sill. BecareDl
notto let _bJnet failon_ screwsare removed,
• Removecabinet from windowopening.
•Placeair conditionerinto _bJnet. Reinstallsidescrews
and Front Grii_e,
° Placeunitand all assembly h_dware inair conditioner
shippingcarton, and storein clean,dry #ace.
• Air _nditioners covered in this manual pose an
excessive weight hazard. Two or more people
are ne_ed to move and install the unit.
To prevent injury or strain, use proper lifting and
carrying techniques when moving unit.
° When handling the air conditioner, be careful to
avoid cuts from sharp metal fins on front and
rear coils.
•Make sure air conditioner does not fall during
removal.
-8-

HOW AND WHY
Your room air conditioner provides the following
functions to make hot weather iiv[ng more
comfo_able:
• Coo_sand circulates room air
*Lowers humidity by removing excess moisture.
, Filters out summertime dust, diR. and some
airborne impurities.
The air conditioner performs these functions by
drawing room air through a filter which traps dust
and dirt particles. The air then passes over a
cooling coil which refrigerates the air and removes
excess moisture. The same air is then returned to
the room- coo_er, drier, and cleaner. Moisture
removed from the room air is carried to the outside
and evaporated.
'(our air conditioner is designed to be easy to
operate and to provide pienty of cooling power.
NORMAL SOUNDS F G.21
Aside from the r_ular fan motor and compressor
sounds coming from your air conditioner, you will
once in a while hear a pinging sound This is the
result of moisture being picked up from the air in the
room and thrown against the air conditioner's fan.
This is norma! and should not be cause for concern.
Also, do not:be alarmed if you hear a slight hissing
or gurgling sound coming from your air conditioner
after it is off. These are normal coolant noises,
The modern high efficiency
compressor may have a high
pitched hum or pulsating
noise that cycles on and off.
Unit Vibration
The unit may vibrate
and make noise
because of poor wall
or window const_ction.
Fan
You may hear air
movement from
the fan.
_en_r
You may hear droplets of water hitting
the condenser causing a pingingor
clicking sound.
FIG. 21
CAPACITY AND RUNNING TIME
Proper unit size is impo_ant in deciding the desired
comfort for the area you want to cool. An
undersized unit will not have the capability to cool,
_eavingthe area uncomfortably warm. The proper
size is determined by the number of square feet in
the area to be _l_, indoor and outdoor
temperature and humidity.
Whenever the heat or humidity load is a_ve normal
the air _nditioner must run longer and more often
to keep the desired temperature you have selected
Under heavy heat load conditions the air conditioner
may need to run constantly to keep the temperature
you want,
At times using the MED FAN setting to circulate the
r_m air may make it comfortable even though Lhe
air is not being cooled. This will decre_e your cost
of use.
-9-

1 15 6 5 4 316 2714
_ILT#
tltl
11 i2 10 13 i7
FIG. 22
1. Cabinet
2. Vertical Air
Direction Louvers
3. Horizontal Air
Direction Louvers
4. In_etGrille
5. Air Filter
6. Front Grille
7. Control Board
8. Power Cord
9. Evaporator Coil
10. Condenser
11, Compressor
12. Base pan
t 3.8race
14. Upper Guide
15, Curtain
16. Vent Control Lever
17. Remote Control
USING THE AIR CONDITIONER
To reduce the risk of fire, electric
shock, or injury to persons, re_ the important
SAFETY instructions section before operating this
appliance
To begin operating the air conditioner after
installation, follow these steps:
1. Plug in the air conditioner. (To prevent electrical
hazards, do not use an extension cord or an
adapter plug.)
2. Set the exhaust vent to the CLOSE position,
3. Set the TEMP Control to the coolest setting.
4. Set the MODE control at the highest COOL level
5, A_ust the louvers for comfortable air flow.
6, Once the room has cooled, adjust the TEMP end
Mode Contro_ to the setting you find most
comfortable.
NOTE : if the air conditioner is turned off, wait 3
minutes before restarting. This allows pressure
inside the compres_r to equalize. Failure to wait 3
minutes before restarting may cause inefficient
operation,
ifyou move the TEMP Contro_ to a warmer, then
immediately back to a cooler setting, the unit will
shut off. Wait 3 minutes before restarting.
VENT CONTROL
The Vent Control allows the air conditioner to
either recirculate inside air (CLOSE) or exhaust
air to the outside (OPEN). (FIG. 23)
• The CLOSE position is used when maximum
cooling is desired Itmay also be used for air
recirculation without cooling when the air
conditioner is set in the FAN position.
• The OPEN position removes stale air from the
room and exhausts it to the outside. Fresh air is
drawn into the room through your home's
normal air passages
• The OPEN or CLOSE _sition can be used with
any fan selection.
PULL OPEN !PUSH CLOSE FiG. 23
-10-

CONTROL PANEL
FAN SPEED
• Every time you push this button, it advancesthe setting as follows: {High_ Low_ Med High}
REMOTE OONTROL SIGNAL
• Usethis button to automatically control the
temperature of the room.
The temperature can be setwithin a range
of 60_Fto 86°F by increments of 1°F.
•.The _tting appears in the display.
- SHUT-OFF TiME
•"Youwill usually use shut-offtime while you sleep.
• If un_is running,usetimerto setnumberofhoursuntilshut-off,
•ToturntheairconditionerON,pushthebutton.
Toturntheair_nditioner OFF,_sh
thebuttonagain.
•Thisbuttontakespriodtyoveranyotherhuron,
•Whenyoufirstturniton,theaircondH:ionerison
theHighcoolmodeandtheTemp.at 72°F.
•Autorestart
•Foryoursleepingcomfort,oncetimerisset,thethmperature Int_ eventasa _wer failure,t_ un_willrun
settingwillraige2°Fafter30rainandonceagainafteranother30rain. atthep_eviousse_ingoncepowerreturns.
• Pushtimerbuttontoadvancesettingfrom t Hour _2Hour.... _12Hoursmaximum,
oSTARTTIME
• If unitis off,Timersetsnumberof hoursbeforeunitstarts.
• Pushtimerbuttontoadvancesettingfrom 1 Hour , 2Hour..... _12Hoursmaximum.
_-MODE
- Push this button to shi_ mode of operation from cool -* energy saver _ fan.
-ENERGY SAVER:
- The fan stops when the compressor stops c_ling.
Approximately every 3 minutes the fan will turn on so that the unit can check the room air to determine if
cooling is need_,
[In _lt°lo_t_elefcl[_cmpower, the unit runs as previous settir_g operation. }
HORIZONTAL AIR DIRECTION CONTROL
The horizontal air direction is adjusted by moving
the vertical _ouvers right and left with your
fingertips. (FIG. 24)
VERTICAL AIR DiRECTiON CONTROL
The vertical air direction is adjusted by moving the
horizontaE louvers up and down with your fingertips.
(FIG. 25),
FIG. 24 FIG. 25
-1t -

REMOTE CONTROL
NOTE: The Remote Control will not operate properly if strong light shines on the sensor window of the Air
Conditioner or if there are obstacles between the Remote Control and the Air Conditioner.
Every time you push button, you will hear a beep from the Air Conditioner
•Toturnthe airconditionerON_pushthe button,
Toturntheair conditionerOFF_pushthebuttonagain.
, This buttontakespriorityoveranyotherbutton.
, Whenyoufirstturniton,theaircz)nd_ionerisontheHighcoolmodeandtheTemp.at72°R
, Autorestart
Intheeventasapowerfa_ure,theunitwill_unattheprevioussettingon_ powerreturns.
TEMPERATURE SETTING
• Use this button to automatically control the tem_rature of;the room.
Thetem_rature can bo set within a rangeof 60°F to 86°F by incrementsof 1°F.
• The setting appears in the display.
FAN SPEED
• Every"time you pushthis button itadvancesthesettingasfollows:
(High`Low Med High) !
*You will usually use shut-off time while you sleep.
, If unit isrunning,usetimerto set numberof hoursuntilshut-off.
. Foryoursiccing _mfort, oncetimerisset,tie thmperature
settingwillraige2°Fafter30minandonceag_n aftera_t_r 30rain
. Pushtimerbuttonto advancesettingfrom1 Hour-, 2Hour......_12 Hoursmaximum,,
oSTARTTIME
. If unH:isoff,Timer setsnumberof hoursbeforeunitstarts.
. Pushtimerbuttonto advancesettingfrom 1 Hour _2Hour........J2 Hoursmaximum,
POWER
- Push this button to shift mode of operation from _ol ........energy star, fan.
- ENERGY SAVER:
• The fan stops when the compressor stops cooling.
Approximately every 3 minutes the fan will turn on so that the unit
can check the room air to determine ifcooling is needed.
HOW TO INSERT BAKERIES INTO REMOTE CONTROL
1.Removet_ _ver from the _ck ofthe remote
controller.
•Openthe cover accordingtothe arrowdirectionon the
cover.
2. inserttwo battedes.
•_ surethatthe (+) and (o)directionsare correct.
• Be _re that both batteriesare new.
3. Re-attachthe cover.
, Donot userechargeablebatteries,
Suchbatteriesdifferfrom standard drycells in _ape,
dimensions,and performance.
, Removethe batteriesfrom the remotecontrollerifthe air
conditioneris notgoingto be usedforan e_erded
lengthof time.
• TEeremote controlcan be mountedon a wall usingthe
mount_le holder.
-12-

AIR FILTER CLEANING
The Air FHterwill become dirty as it removes dust
from the inside air, ft should be washed at _east
every 2 weeks. If the Air Fi_terremains futl of dust,
the air flow will decrease and the cooling capacity
will be redu_d, possibmydamaging the unit.
• Pull the inlet gdHeforward, grasping both tabs,
then pull out the air filter, (FIG. 26)
• Wash the Air Fi_terunder the faucet with warm
water. Be sure to shake off ai! the water before
replacing the filter. (FIG.27)
FIG.
FIG, 27
AIR CONDITIONER CLEANING
Clean the front grille and inletgrille by wiping with a
cloth dampened in a mi_ddetergent
solution.(FIG.28)
The cabinet may be washed with mild soap or
detergent and lukewarm water, then polished with
liquid appliance wax.
To ensure continued peak efficiency, the condenser
coils (outdoor side at the unit) should be checked
periodically and cleaned if they b_ome clogged
with soot or dirt from the atmosphere. Brush or
vacuum exterior coils to remove debris from fins.
FIG. 28
HOW TO REMOVE THE FRONT
• Open the, in_et grille downward.
• Remove the screw securing the Front GdHe,
• Push the grille up from the bottom and pull the top
of the grille away from the case to lift the top tabs
out of their slots.
Gdlle
FIG. 29
HOW TO REPLACE THE
FRONT GRILLE
Attach the front grille to the cabinet by inserting the
tabs on the grille into the slots on the front of the
cabinet. Push the grille in until it snaps into pJace.
0FIG, 30
-3-

BEFORE CALLING FOR SERVICE
Check the following list to be sure a service call is really necessary. A quick reference to this manual may
help you avoid an unneeded service call.
THE AIR CONDITIONER WILL NOT OPERATE
Check if... Then...
Wallplug disconnected.
House fuse blownor circuitbreakertripped.
Poweris OFF.
Unit wasturned offand thenontoo quickly.
TEMP Controlset warmer thanroom temperature.
The current interrupter device is triped
Push plug firmly intowalloutlet.
Replace fusewith time delay type or resetcircuitbreaker.
Pushthe powerbutton.
Set unitoff and wait 3 minutesbeforerestarting.
Set TEMP Controltocoolertemperature.
Press the RESET button located on the power cord plug
Ifthe RESET button will not stay engaged, discontinue use of the
air conditioner and contact a qualified service technician.
AIR FROM UNIT DOES NOT FEEL COLD ENOUGH.
Check if... Then...
FAN SPEED setat LOW. Push FANSPEED button to setat HIGH.
TEMP Controlset too warm. SetTEMP Controlto a coolertemperature.
Roomtemperaturebelow70°F (21°C). Coolingmay not occuruntilroom temperaturerises above70°F (21'C).
Temperaturesensing tubetouching evaporatorcoil, Removethe frontgrillethen
locatedbehindfront grille, straightentube awayfrom evaporator coil.
THEAIRCONDITIONERCOOLING,BUT ROOMISTOO WARM-ICE FORMINGONCOOLINGCOILBEHINDFRONTGRILLE.
Check if... Then...
Outdoortemperaturebelow 70°F (21°C). To defrostthe coil, setthe MODE to FAN.
Airfilter may bedirty. Cleanair filter. Referto Maintenancesection ofowner's manual.
TEMP Controlsettoo cold for night-timecooling. Todefrostthecoil,setthe MODEto FANspeed to"HIGH"withthe
TEMPcontroltowarmertemperature.
THEAIRCONDITIONERCOOLING,BUTROOMISTOOWARM.
Check if...
Dirtyairfilter- air restricted.
TEMP Controlset too warm.
Frontof unitis blockedby drapes,blinds,furniture,etc.
Airdistributionis restricted.
Doors,windows,registers,etc.open. Coldair escapes.
Unit recentlyturnedon in hot room.
Then...
Cleanair filter. Referto Maintenancesection ofowner's manual.
Set TEMP Controltocoolertemperature.
Clear blockagein frontof unit.
Close doors, windows,registers,etc.
Allowadditionaltimetoremovestoredheatfromwalls,ceiling,floor,andfurniture.
THE AIR CONDITIONER TURNS ON AND OFF RAPIDLY.
Check if... Then...
I Outsidetemperatureisextremelyhot. I SetFANSPEEDonHIGHtobringairpastcoolingcoilsfaster.
NOISE WHEN UNIT IS COOLING.
Check if... Then...
Soundoffanhittingwaterfromthemoistureremovalsystem. Thisisnormalwhenhumidityishigh.Closedoors,windows,andregisters.
Windowvibration- poorinstallation. Refertoinstallationinstructionsorcheckwithinstaller.
WATER DRIPPING INSIDE ROOM WHEN UNIT IS COOLING.
Check if... Then...
Theairconditionerisimproperlyinstalled. Tiltairconditionerslightlytotheoutsidetoallowwaterdrainage.Referto
installationinstructionsor checkwithinstaller.
WATER DRIPPING OUTSIDE WHEN UNIT IS COOLING.
Check if... Then...
Theunitisremovinglargequantitiesofmoisture Thisisnormalduringexcessivelyhumiddays.
fromhumidroom.
-14-

INDICE DE MATERIAS ............................. 15
GARANTiA ................................................ 15
SEGURIDAD .............................................. 16
Importantes instrucciones de seguridad ..... 16
REQUERIMIENTOS ELECTRICOS ......... 17
INSTALACION DEL CABLE ELECTRICA ...17
INSTALACION ........................................... 18
Requerimientos para instalaci6n .......... 18
Installaci6n ............................................ 19
C6mo instalarlo ..................................... 19
La eliminacion de la ventana ................. 21
OPERACION .............................................. 22
C6mo y por que ..................................... 22
Sonidos normales .................................. 22
Capacidad y tiempo de funcionamiento .--22
Caractedsticas ..................................... 23
Uso del equipo de aire acondicionado ..23
Despliegue ............................................ 24
Control remoto ....................................... 24
MANTENIMIENTO .................................... 26
Limpieza del filtro del aire ...................... 26
Limpieza del equipo de aire acondicionado ....26
C6mo sacar la rejilla frontal ................... 26
Como a reemplaza el grille anterior ...... 26
CORRECCION DE FALLAS ...................... 27
Antes de Llamar para Sewicio ...................... 27
ACUERDOS DE PROTECClON
ESPEClALIZADA ...................................... 31
PARA PEDIR SERVlClO ....Cubierta Trasera
GARANTIA DE UN ANO POR EL
EQUlPO DE AIRE ACONDIClONADO
DE HABITAClON
Durante un afio completo a partir de la fecha de
compra, si este equipo de aire acondicionado recibe
mantenimiento y se utiliza para el enfriamiento
normal de habitacion segt3n las instrucciones
indicadas en este manual del propietario, Sears
reparara, gratuitamente este equipo de aire
acondicionado, si tiene algt3n defecto en materiales
o fabricaci6n.
GARANTIA TOTAL DE ClNCO ANOS
POR EL SlSTEMA DE REFRIGERAClON
HERMI_TICAMENTE SELLADO
Durante cinco afios a partir de la fecha de compra,
si este equipo de aire acondicionado recibe
mantenimiento y se utiliza para el enfriamiento
normal de habitaci6n segen las instrucciones
indicadas en este manual del propietario, Sears
reparar& gratuitamente el sistema de refrigeraci6n
hermeticamente sellado (que consiste en el agente
refrigerante, los tubos de conexion y el compresor),
si tiene algL_ndefecto en materiales o fabricacion.
EL SERVICIO DE GARANTiA ES
DISPONIBLE CONTACTANDO AL SERVIClO
SEARS AL 1-800-4-MY-HOME e
La proteccion de garant[a cubre unicamente a
los equipos de aire acondicionado usados para
uso domestico y no para uso comercial.
Esta garantfa solo tiene validez mientras el
producto se este usando en los Estados
Unidos.
Esta garantfa le da derechos legales
especfficos y usted puede tener otros
derechos que varian de estado en estado.
Distributed by Sears, Roebuck and
Co., Hoffman Estates, IL 60179
-15-

IMPORTANTES INSTRUCCIONES DE SEGURIDAD
Las siguientes instrucciones de seguridad le indicaran c6mo usar su equipo de aire acondicionado de
habitaci6n para evitar daSos para usted mismo y para su EQUIPO DE AIRE ACONDIClONADO.
POR SU SEGURIDAD
No almacene ni use gasolina u otros vapores y
liquidos inflamables cerca de este o cualquier otro
electrodomestico. Lea las etiquetas de los
productos para ver si contienen advertencias sobre
el cargtcter inflamable de los mismos y otras
advertencias.
PARA PREVENIR ACCIDENTES
Para reducir el riesgo de incendios, descargas
electricas o lesiones personales al usar su equipo
de aire acondicionado, tome las precauciones
basicas, entre las que estan las siguientes:
• AsegQrese de que la alimentacion electrica sea la
apropiada para el modelo que usted ha elegido.
• Si el equipo de aire acondicionado debe instalarse
en una ventana, a usted probablemente le
conviene limpiar primero ambos lados del vidrio.
Si la ventana es del tipo de tres paneles con un
panel incluido de pantalla, le conviene sacar la
ventana completamente antes de la instalaci6n.
• AsegQrese de que el equipo de aire
acondicionado ha sido instalado correctamente y
con seguridad segOn se sefiala en las
instrucciones separadas de instalacion que vienen
en este manual. Conserve este manual y las
instrucciones de instalaci6n para usarlos
posiblemente en el futuro al sacar o volver a
instalar esta unidad.
• Use guantes al manejar el equipo de aire
acondicionado, tenga cuidado para evitar cortadas
con las afiladas aletas metalicas que se hallan en
los serpentines frontales y posteriores.
INFORMACI(_N ELECTRICA
En la placa de serie del fabricante se indica cu&l es
la capacidadelectricanominalcompletade sunuevo
equipo de aireacondicionadopara habitaci6n.Consulte
esta placacuandovaya averificarlosrequerimientos
electricos.
• AsegQresede que el equipode aireacondicionado
tenga unaconexi6ncorrectaa tierra.Para reduciral
minimo losriesgosde descargaselectricase incendio,
es importanteconectarelequipo correctamenteatierra.
Elcord6nde alimentaci6nelectricaesta equipadocon
un enchufedetres espigascon conexi6na tierrapara
protegerlecontra riesgosde descargaselectricas.
• Su equipode aireacondicionadodebe enchufarseen
unatoma de corrientede paredquetenga unaconexi6n
correctaatierra. Si latoma de corrientede paredque
usted piensausarnoesta conectadacorrectamentea
tierrao no esta protegidaconun fusiblede accion
retardadao con un interruptorde circuito,hagaque un
electricistacalificadole instalelatoma de corrientede
pareden forma correcta.
• Noponga a funcionarel equipo de aire acondicionado
con una cubiertaprotectoraexteriorencima.Estopodria
ocasionardafios mec&nicosdentrodel aire
acondicionado.
• No use un cable de extensi6n ni un enchufe
adaptador.
Evitelospeligrosde incendiosy
descargaselectricas.Nouseuncabledeextensionni un
enchufeadaptador.Noelimineningunade lasespigas
delenchufedelcordonde alimentacionel6ctrica.
Toma de corriente
de pared con I "'_-._. Cable de
conexi6n a tierra. I /T2,,,"_ alimentacidn
I \-l lLconclavija
/_,.\ ?__1 '\_. I II dotada de
Hep°nga"[m_,_l'_ I #_X-" II conexi6n a
_-_I[ i/tL_/I _'_'k II tierrade3
Prueba__ l_ _ terminales.
"1_ Terminal de
I I conexidn a tierra.
[ _ I
Bajo ninguna circunstancia core, quite o evite
el uso de la conexidn a tierra de esta clavija.
IDEAS PARA AHORRAR ENERGiA
•La capacidad del equipo de aire acondicionado
debe corresponder al tamafio de la habitaci6n
para el funcionamiento eficiente y satisfactorio del
equipo.
•Instale el equipo de aire acondicionado de
habitacion en el lado sombreado de su hogar. Una
ventana orientada hacia el norte es la mejor
porque tiene sombra la mayor parte del dia.
• No bloquee el aparato de aire acondicionado
tap&ndolo con persianas, cortinas, muebles o en
el exterior con arbustos, recintos u otros edificios.
• Cierre el regulador de tiro de la chimenea, las
rejillas de calefacci6n del piso y la pared, de tal
modo que el aire fdo no se escape ni por la
chimenea ni por los conductos.
•Mantenga las persianas y las cortinas de otras
ventanas cerradas durante la parte m&s soleada
del alia.
•Limpie el filtro del aire como se recomienda en la
secci6n "MANTENIMIENTO" de este manual.
• El aislamiento correcto y las juntas hermeticas en
puertas y ventanas en su hogar le ayudar&n a
mantener el aire caliente afuera y el aire frio
adentro.
•AI darle sombra externamente a la casa con
&rboles, plantas o toldos ayudar& a reducir la
carga de trabajo del equipo de aire acondicionado.
•Opere los aparatos que producen calor como, por
ejemplo, hornos, lavadoras, secadoras y
lavaplatos durante la parte mas fria del dia.
-16-

RESP_ETODOSLOSCODIGOSYREGLAME_OS,
8AJO NINGUNAClRCUN_ANCIA CORTE,QUITE0
EVITEEL USODELACONF_ONA TIERRADEESTA
CLAVIJA.
ESTEAPARATONECESiTASERCONECTADOA_ERRA,
Se requiereuna_imentaci0nelectricaCA,adecuadamente
_necta_ atierraconunfusiblede 15A, _ 60 Hzy
230/208V. Se r_mie_a unfusiblederetardoo un
disyuntordecircuitoque_imente_lamente a esteaparato.
NOUSECABLEELEC_RICODEEXTENSION,
MF.TODORECOMENDADODECONEXIONATERRA
Persupropiasegaddsdesteacetatedebeconectarseatierr&Esle
apa_alovieneequipado®_qun_bte dealirnentaci6_yunaclaviia
tresterminales.ParareduciralmAximoelpeligrodechequeele_rico,
el_b/e _be eslarcor_ectadoauna®r_exbr_dep_red®n®nexi6n
atier& yestaconexion_be h£cersedeacuerdoco_laaltim8
ediciSn€_ICSdigoB_rico Nacior_(AN%NFPA701_,asi®mecon
los_digosyr_lamentoslocales.Si_oexisleunaconexbn
pared8_:_ec#_da,e/c/iente_enelaresponsabilidsdylaobligacbnde
m_n®rins_£1ar,conanelectricisl£caiifica®,un£conexbndep£_ed
adecuadede_ termi_lesconconexionatierr&
1i5V ~ 230W EIcablede alimentaciOnpuedeJnduirundis_sitivo
interrupterdecorrode. Lacarcasadelenchufecuenta
con_n_tdn _ pr_abayottodereinicb.B dJspositJvo
dabe®mprobarseperiOdicamentepresionan@
primeroel botonTESTyd_pues RESET_
Siel boronTESTnose@sconectao siel bot6n
RESETnopermane_act_vo,su_enda el _so@1aire
acondiciona@yp6ngaseencon_ctoconunt@nico
deservidocualificado.
NOTA: La forma puede set diferente segt_msu m_elo.
Utili_ el enchufede la pared Consume de Energ_a
Standard 125V,
enchufe _ 3
Uneas de
15A_ 125V AC Uti/ice un fusible de
15AMP. o un
Slandard 250V, r_terruptor de 15AMP.
enchufe de 3
Lineas de
15A 250V AC
Standard 250V,
ench_fe de 3 UtHice un f_sible de
Lineas de 20AMP o un
20A, 250V AC I_terruptor de,20AMP,
Peligro de cheque el_ctri_
Conecte en una c_nexi6n de pared _ 3 terminales
No quite _aterminal de _exi6n a tierra
No use adaptadores
No use _b_e e_ectricode extension
Si no se siguen estas instrucciones, puede ocasienarse
_am_erte, un ince_dio o un cheque e_tnco,
Puedee_ger e_re los dos metodosabajo descntosde a_erdo a la forma del taburetede su ventanay su #-eferencia,
UTILIZANDO LA RANURA "A"
Aprete el obtura_r usando 2 hoyos de torniHo, y
saque el cable el_ctrico a traves de la ranura "A".
UTILiZANDO LA RANURA "B"
Aprete el obturador usando el hoyo izquierdo de
torniilo, y gire apropiadamente para sacar el cable
el¢ctrico a traves de la ranura "B".
-17-

REQUERIMIENTOS PARA INSTALACION PI_AS DE MONTAJE
Su equipo de aire acondicionado se instalara en
ventanas estandar de doble panel con anchos de
abertura libre de 737 mm a 1041 mm (29 a 41
pulgadas). (Figura 1)
El marco inferior debe abdrse _osuficiente para
permitir una abertura vertical libre de 483 mm (19
pulgadas). Las rejillas desviadoras laterales y _a
parte posterior del equipo de aire acondicionado
deben tenet un espacio libre de aire para perrnitir
suficiente flujo de aire a traves del condensador
para asi eliminar el calor. La parte posterior de la
unidad debe quedar al aire libre, no dentro de un
edificio o garaje. Banda
_cho
Figura 1
SERVIClO ELECTRICO
Comprue_ cu_iJes la alimentacJ6nel6ctri_ que Hegaa
su domicilio.La a_imentacJ6nelectricadisponiMe_
_r la mismaque _ muestraen _apla_ del fabricate
la unidad(que sehalla en el ladoderechodel gabinete
cornentea_tema),
Todos los modelosestanequipadoscon un e_hufe de
tres espigas parasuministrarun serviciocorrectoy una
conexi6na tierra _gura y positiva. Nocambie el enchufe
de ningunaforrna.Nouse un enchufeadap_ador.Si su
toma de cordentede paredactual no puede u_rse conel
er_hufe deI equipo,llamea un electricistacalificado para
que efectue_ascorrecciones_rias.
CONSERVELA CAJAy este MANUALDEL
PROPIETARIOpara que le sirra comorefere_ia en el
futuro, Lacaja esla mejormanerade con_war la unidad
duranteel inviemoo cuando no estaen u_.
Paraevilarel r_sgode _sbn_ ._r_rral_, danosa sJ
pro#e_d od_s ,_prodL_ode_d_al_so _ este
_u poy ostiosa q_ seranexpu_:
• El_reacondkJonado_1 que_ habhenestemanual
afirma_ligro de _so exces_vo.
D_ o mas_rsor_s serequire_a movere ir_talajla
unidad.Paraever her_ o ago_arn_nto,u_ tecn_
aFrOs para_v_r ytroverJaun_ad.
•Cuidado_menteins_cbre elI_ar do_e elaire
acon_ionadosera_o, A_ure_ q_ el_u_
soster_ael_ de_ unidadso'breunpenodode
flempo_olon_o.
•Manl_a _ _re acond_onadocon_Mado. U_
,quan_s_otecloresc_r_o le_a,_eomueva_ uni_.
EVITElasa_tasfilo_ demealenelse_n
_la_ero y_ arras,
•Aseguresequeelaireaco_Jciona__ se_a
durantelain_adon.
A B N
F
C D E
K
_EM NOMBRE DE LAS PIEZAS CANq'IDAD
A PANEL DE GUIA 2
B SOPORTE 2
C SOPORTE DE ANTEPECHO 2
D CONTRATUERCA 4
E TORNILLO: 25/64" 11
F TORNILLO: 1 3h6" 7
G TORNILLO: 9/16" 5
H TORNILLO M 2
I BULON 2
J ClNTA DE ESPUMA 1
K ClNTA DE ESPUMA 1
L SOPORTE DE CERRADURA 1
M TUBO DE DRENAJE 1
N TORNILLOS 1
HERRAMIENTASREQUERIDAS
• Guantes apretados
, Destomillador normal
• Destornillador Phillips
- Pinsas
• Cuchillo filoso
, Uave inglesa o Ilave abierta de 3/8"
, Uave hexagonal de cubo y trinquete de 114de
pulgada
• Cinta para medir
• Taladro electrico
• Broca de taladro de 1/4"
-8-

Escoja un _ugarque le permita Ilevar e] aire frio a_area
que dese& Las ventanas que se usen para la
instalad6n deben tener Jares[stenc[a suficiente para
soport_ el peso del equipo de _re acondicionado. Una
buena [nstalad6ncon atend6n es_cia] a la correcta
posici6n de la unidad dismJnuir&]a probab[lidad de que
sea necesario efectuar reparadones.
Cuando se desea enfdar mas de una habitad6m Ia
insta_aci6nes muy im_rtante puesto que el aire fr[o no
dobla esquin_. Para enffiar sus habitaciones, el aJre
fifo debe despiazarse desde eEequipo de aire
acond[cionado en una trayectoda recta.
COMO INSTALARLO
_ Saque los tornillos que aseguran el gabinete en
ambos lados yen la parte posterior.
_ DesHce ]a un[dad sacgndoIa de su gabinete
agarrando e] asa del recip[ente de _abase y tirando
de ella hacia deIante mientras sostiene el g_inete.
_ Corte la cinta de espuma (ITEM J) a ]a
extension _ropiada.
Despegue e] refuerzo y pegueb en el _adode _aio
del marco de la ventan&
Figura 5
Q Inseitelos _nel_ deguia (ITEMA) enlaguiasupedor
y lasgutasdemarcodelequi_ _ aire acondicionado.
Sujetelascortinasenla unidad_n lostomillos(iTEME)
ITEM
Guiamasbaja- iTEMEFigura 6
_Abra la ventana.Marqueuna tineaen e[centrode ia
rep[sede la ventanaentreI_ moldesde topelateralde la
ventana.Fijesin apretarel soportede _tepecho (iTEMC)
al otrosopode(ITEMB) usandoel bulon(ITEMl) y la
_ntratuerca (iTEM D),
ITEM
ITEMI
Rje el soporte de ante_clho al ante_c_ a la
ventana usando los tomillos (ITEM F). Coloque
cu[dadosamente e_gabinete _bt_ la re_ de la ventana
y alinee la marca de__ntro en la parte frontal infedor con
_alfnea central marcada en la repisa de la ventan&
para metales y
t'atuerca
de/
antep_ho de la
ventana
(iTEMF)
Bul6nycontratuerca ' Figura 8
So_rte de antepecho
U Usando e_tornillo M (iTEM H) y la contratuerca
(ITEM D), fije el soporte al or[f[c[o de _rfil del gabinete,
Use el primer orificio de earth despu_ del so_orte de
ante_cho en el _rde exterior del antepecho de ventana.
Apriete el bulon y ia contratuerca. Aseg_rese de que.e_
gabinete se incline hacia fuera '1/4de gota usando el nivel.
CUIDADO:Noperforeunorificioen el recip[enteinferior.
Laun[dad_ta diseSadaparaoperar_n aproximadamente
1/2pulgadade aguaen el recipienteinferior.
8
Gabin_e
iNTERIOR EXTERIOR Figura 9
-19-

_Tire del marco inferiorde ]ave_ana haciaabajo
detras de la gu[asupedorhasta que se encuentre[aguia
conel marc4),
NOTA:
• Notire de] marcode la ventanatan hacia abajoque
restHnjael mov[mientode ]ascorredera& Fije el
ga_nete a la rep[sade [aventana atomi]landebs
torni]los (iTEM F)a travesdel gabineteen [arepisa de
]a ventana.
• Elgabinetede_ instalarse1/4de gota de el nivel, hecia
abajo y haciafuera,
de
e_um_
Gabinet
En_adre
_rtina
ITEMF
Figura 10
_ Extienda el panel hasta ]]enar eEhueco.
Fije cada panel guJa en el marco de la ventana usando
dos tomiHos (iTEM G). (Figura 11)
ITEMG
Guide Figura 11
_Se debe instalar el asa antes de fijar el ffente
decorativo. (Figura 12)
G
Figura 12
DREANJE
En la p,_te posterbrdela unidadde Nreac_dicbnado hay
un orificio de drenaje. _le_[o_ un metodo de drenaje
seg_nlassiguientesi_truc-cb_s:
• Saq_ de_red#entede base_agomadelorificb.
•Conecteuna rra_era de drenajede 9/16°de pulgadade
diametroi_rr.e a_tubodedren_e_m<) _ mue_r&
•Conecte un _ de tu_ de 9/16"de _Jlgadade d_metro
interne al tubo de drenaje, conecte _guidamente una
manguera de dren_e de 9/16" de pulgada de d[ametro
intemoal _do del_bo comosemues_a.(Elequipodeare
acondidor_donovieneconunarrar_uera dedre_e.)
' I
Tubo _ _ Tubo de
drena !,
Manguera
de drenaje Manguera de drenaje
Figura i3
_ Des]ice el chasis hacia el interior del gabinete.
(Figura 14)
CUIDADO: Con fines de seguridad vue,_vaa
instalar los tornHlos en los ]adosdel gab[nete,
Tornilb
Cord6n de Tomi[llo
el_ctri_ Figura 14
Corte _ajunta herm6tica de espuma([TEM K)
para que tenga la iongitud apropiada e inserteia
entre emmarco superior y el mar_ inferior de _a
ventana. (Figura i5)
Figura 15
Ajuste el asa antes de fijar el frente decorativo.
(Figura 16)
Enderence el kit de ventiLacion _mo se indica,
halando hacia debajo de la parte <_:_.I_evando]aen ]a
linea horizontal _n ]apa_e @,
-20 -