Kenwood kMix ZJX650 User manual

English 2 - 6
instructions
TYPE ZJX650
Kenwood Ltd
New Lane
Havant
Hampshire
PO9 2NH
kenwoodworld.com
© Kenwood Ltd 2018 139610/1

safety
lRead these instructions carefully and retain
for future reference.
lRemove all packaging and any labels.
lIf the cord is damaged it must, for safety
reasons, be replaced by KENWOOD or an
authorised KENWOOD repairer.
lNever use a damaged appliance. Get it
checked or repaired: see ‘service and
customer care’.
lAlways use the filter and never overfill -
boiling water may splash out.
lAvoid contact with steam coming out of the
spout area when pouring and out of the lid
or spout area when refilling.
lBeware: the body of the kettle will get hot
during operation.
lNever let the cord hang down where a child
could grab it.
lAlways unplug your kettle when not
in use.
lNever put the kettle, powerbase, cord or
plug in liquid.
lCaution: Do not operate the kettle on an
inclined surface.
lOnly use the powerbase supplied and keep it
clean and dry.
lMake sure the lid is secure before switching
the kettle on.
lWarning: Do not open the lid while the
water is boiling.
lTake care when opening the lid - droplets of
hot water may be ejected.
English
2
f
h
i
b
c
d
e
g
a
1
2 3

lMake sure the kettle is switched off before
lifting or pouring.
lRemove the kettle from the base before filling
or pouring.
lNever put the kettle near or on cooker hot
plates or gas burners.
lThis kettle is for boiling water only.
lMisuse of your appliance can result in injury.
lChildren from 8 years and above can use,
clean and perform user maintenance on
this appliance in accordance with the User
Instructions provided they are supervised
by a person responsible for their safety and
have been given instruction concerning the
use of the appliance and are aware of the
hazards.
lPersons with reduced physical, sensory or
mental capabilities or lack of knowledge
using this appliance must have been given
supervision or instruction on its safe use and
are aware of the hazards.
lChildren must not play with the appliance
and both appliance and cord must be out of
reach of children less than 8 years.
lOnly use the appliance for its intended domestic
use. Kenwood will not accept any liability if the
appliance is subject to improper use, or failure to
comply with these instructions.
3
before plugging in
lMake sure your electricity supply is
the same as the one shown on the
underside of your kettle.
l This appliance conforms to EC
Regulation 1935/2004 on materials
and articles intended to come into
contact with food.
before using for the first time
1 Wrap any excess cord around the
bracket h on the underside of the
powerbase.
2 Fill to ‘MAX’, boil, then pour the
water away. Repeat 3 times.

key
a spout
b finger pad
c flip top lid
d lid release button
e on/off switch
f water level gauge
g 360° powerbase
h cord wrap
i filter
to use your kettle
1 Press the lid release button d to
open the lid, then fill the kettle. The
water level must be between ‘MAX’
and 1 cup (250mls).
lIf you live in a hard water area we
recommend that you use filtered
water in order to maintain the
appearance and efficiency of your
kettle.
lBe economical: do not boil more
water than you need.
lTo improve the quality of your drinks
always use fresh water.
lEmpty the kettle after each use.
lRinse out with fresh water if the
kettle has not been used for more
than 2 days.
2 Close the lid by pushing down on
the finger pad area 1.
3 Plug in and switch on.
4 Your kettle will boil and switch off
automatically. To re-boil, wait a few
seconds - the on/off switch needs
time to reset.
Note - To interrupt the boiling
ensure that the switch is
in the off position before
removing from the powerbase.
lIf you experience problems
with your kettle switching
on and off during use or
switching off before boiling,
check that the flat element
is free from scale - see
“descaling”.
lYour kettle is fitted with a filter to
hold back limescale particles.
lIf you find drops of water under
your kettle, do not worry - it is just
condensation.
boil-dry protection
lIf you switch on with too little water,
your kettle will cut out automatically.
Switch off, remove from the
powerbase and let it cool down
before re-filling. When it has cooled
down, the switch will reset itself.
care and cleaning
lBefore cleaning, unplug your kettle
and let it cool down.
the outside and powerbase
lWipe with a damp cloth, then
dry. Do not use abrasives - they
will scratch the metal and plastic
surfaces.
the inside
lWipe with bicarbonate of soda on a
damp cloth. Rinse thoroughly.
lEven though your kettle comes with
a filter, you still need to clean the
inside (and the filter) regularly.
the filter
1 Open the lid.
2 Lift the filter out away from the spout
area 2.
3 either rinse under the tap or use a
soft brush or when descaling your
kettle, drop the filter in too. Rinse
thoroughly.
4 Place the filter back in the spout
area and push down to secure 3.
descaling
lRegular descaling of the flat element
will improve the performance of your
kettle. If the kettle is not descaled
regularly the build up of limescale
may result in the following:
lproblems may be experienced
with the kettle switching on and
off during use or switching off
before boiling.
lthe kettle may take longer to boil.
lthe flat element may be damaged.
Please note: Failure to descale your
kettle may invalidate your guarantee.
lWhen limescale starts to build up on
the heating element, buy a suitable
descaler and descale your kettle.
After descaling, boil with fresh water
several times and discard. Clean
any descaler off the kettle - it can
damage the parts.
4

lSome regions of the country have
chalky water. This makes boiled
water look cloudy and leaves a
deposit on the side of the kettle. This
is normal but can be removed with
regular cleaning.
lAlternatively, to reduce limescale
build up, use filtered water to fill your
kettle.
service and customer
care
lIf you experience any problems with
the operation of your appliance,
before requesting assistance refer
to the “troubleshooting guide”
section in the manual or visit
www.kenwoodworld.com.
lPlease note that your product
is covered by a warranty, which
complies with all legal provisions
concerning any existing warranty
and consumer rights in the country
where the product was purchased.
lIf your Kenwood product
malfunctions or you find any
defects, please send it or bring
it to an authorised KENWOOD
Service Centre. To find up to date
details of your nearest authorised
KENWOOD Service centre visit
www.kenwoodworld.com or the
website specific to your Country.
lDesigned and engineered by
Kenwood in the UK.
lMade in China.
IMPORTANT INFORMATION FOR
CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE
WITH THE EUROPEAN
DIRECTIVE ON WASTE
ELECTRICAL AND ELECTRONIC
EQUIPMENT (WEEE)
At the end of its working life, the product
must not be disposed of as urban
waste.
It must be taken to a special local
authority differentiated waste collection
centre or to a dealer providing this
service.
Disposing of a household appliance
separately avoids possible negative
consequences for the environment
and health deriving from inappropriate
disposal and enables the constituent
materials to be recovered to obtain
significant savings in energy and
resources. As a reminder of the need
to dispose of household appliances
separately, the product is marked with
a crossed-out wheeled dustbin.
5

6
Problem Cause Solution
Kettle not operating. No Power. Check kettle is plugged in.
Kettle unplugged. Check kettle is correctly
located to the powerbase.
Kettle not switching off Kettle overfilled. Check water level is not
automatically after above the Max level.
boiling/Long switch
off time. Lid not closed. Check lid is closed correctly.
Water splashing out of Filter not fitted in Always use the filter and do
spout area. spout area. not overfill above the Max
level.
Kettle switching on and Limescale/mineral Check that the element is free
off during use or build up on element from scale.
switching off before affecting operation. Refer to “descaling” section
water boiled. under care and cleaning.
Kettle stopped working Boil dry protection Switch off and remove from
during operation. operated due to the powerbase.
insufficient water in Allow to cool down before
the kettle. refilling.
When the kettle has cooled
down the switch will reset
itself.
Check the water level is
above the minimum level.
If none of the above solve the problem see “Service & Customer Care”.
troubleshooting guide