know your table top
can opener
Your Kenwood Can Opener can be
used to open a variety o domestic
can shapes and sizes. In addition the
CO606 incorporates a bottle opener
and a kni e sharpening acility.
before using your Kenwood
app iance
●Read these instructions care ully
and retain or uture re erence.
●Remove all packaging and any
labels.
sa ety
●Do not immerse appliance, cord or
plug in water or other liquid.
●Never use a damaged appliance.
Get it checked or repaired: see
‘service and customer care’.
●Unplug the appliance rom the
mains supply
●●be ore cleaning
●●immediately a ter use.
●This appliance is not intended or
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack o
experience and knowledge, unless
they have been given supervision or
instruction concerning use o the
appliance by a person responsible
or their sa ety.
●Children should be supervised to
ensure that they do not play with
the appliance.
●Only use the appliance or its
intended domestic use. Kenwood
will not accept any liability i the
appliance is subject to improper
use, or ailure to comply with these
instructions.
before p ugging in
●Make sure your electricity supply is
the same as the one shown on the
underside o your can opener.
Important – UK on y
●The wires in the cord are coloured
as ollows:
Blue = Neutral, Brown = Live.
●The appliance must be protected
by a 3A approved (BS1362) use.
Note:
●For non-rewireable plugs the use
cover MUST be re itted when
replacing the use. I the use cover
is lost then the plug must not be
used until a replacement can be
obtained. The correct use cover is
identi ied by colour and a
replacement may be obtained rom
your Kenwood Authorised Repairer
(see Service).
●I a non-rewireable plug is cut o it
must be DESTROYED
IMMEDIATELY. An electric shock
hazard may arise i an unwanted
non-rewireable plug is inadvertently
inserted into a 13A socket outlet.
●This appliance con orms to EC
directive 2004/108/EC on
Electromagnetic Compatibility and
EC regulation no. 1935/2004 o
27/10/2004 on materials intended
or contact with ood.
key
햲bottle opener
햳drive wheel
햴magnet
햵lever
햶cutter blade
햷guide pin
햸kni e sharpener
햹cord stowage
using your table top can
opener
1 Ensure that the lever is in position
with the magnet housing ully
located (Fig. 1 and 2).
2 Plug the appliance into the power
supply.
3 Li t the lever to the open position.
4 Hold the can with the top rim
resting under the metal guide pin
and the can resting on the drive
wheel (Fig. 3).
5 Press the lever lightly down to start
the motor. The sel -starting blade
will then pierce the can and
commence cutting.
6 The can will be held ixed in position
with the magnet resting against the
lid. Large or wide cans may require
extra support rom the user.
7 Once the can is open, the motor
will automatically stop, retaining the
can and lid sa ely in place.
8 To remove, li t the lever whilst
holding the can.
9 With the exception o aluminium
cans, the lid will be retained by the
magnet.
10 For tidiness, any unwanted length
o cord can be stowed inside the
appliance.
using the bottle opener
When opening tall bottles, the unit
should be used towards the edge
o a work top.
1 Position the bottle with the cap
under the ront rim o the bottle
opener.
2 Push down the bottle to remove the
cap whilst steadying the unit with
one hand.
햲
햵
햷
햸
햹
햶
햳
햴
Fig. 1
Fig. 2
Fig. 3
