Kichler Lighting 52" RENEW DESIGNER User manual

INSTRUCTION MANUAL
Product images may vary slightly from actual product.
52" RENEWTM DESIGNER
UL Model #330163

52" RenewTM Designer | 3
SAFETY RULES
TOOLS AND MATERIALS REQUIRED
PACKAGE CONTENTS
MOUNTING OPTIONS
HANGING THE FAN
INSTALLATION OF SAFETY SUPPORT
ELECTRICAL CONNECTIONS
FINISHING THE MOTOR INSTALLATION
ATTACHING THE FAN BLADES
INSTALLING THE LED LIGHT KIT
OPERATING INSTRUCTIONS
TROUBLESHOOTING
TABLE OF CONTENTS
Read all instructions BEFORE assembly and USE of product
KEEP INSTRUCTIONS FOR FUTURE USE
4
5
5
6
7
10
11
12
13
13
14
15

| KICHLER.COM
4
SAFETY RULES
1. CAUTION -RISK OF SHOCK-
Disconnect Power at the main circuit breaker panel or main
fusebox before starting and during the installation.
2. WARNING:Thisfixture is intendedforinstallationin accordance
with the National Electrical Code (NEC) and all local code
specifications. If you are not familiar with code requirements,
installation by a certified electrician is recommended.
3. WARNING: Suitable for use with solid-state speed controls.
4. WARNING: To reduce the risk of personal injury, use only the
two steel screws (and lock washers) provided with the outlet box
for mounting to the outlet box. Most outlet boxes commonly
used for the support of lighting fixtures are not acceptable for
fan support and may need to be replaced, consult a qualified
electrician if in doubt.
5. WARNING: To reduce the risk of fire, electric shock or personal
injury, mount fan to outlet box marked “acceptable for fan
support”.
6. The outlet box and support structure must be securely mounted
and capable of reliably supporting a minimum of 50 pounds. Use
only CUL Listed outlet boxes marked “FOR FAN SUPPORT”.
7. The fan must be mounted with a minimum of 7 feet clearance
from the trailing edge of the blades to the floor.
8. Do not operate reversing switch while fan blades are in motion.
Fan must be turned o and blades stopped before reversing
blade direction.
9. Avoid placing objects in the path of the blades.
10. To avoid personal injury or damage to the fan and other items,
be cautious when working around or cleaning the fan.
11. Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be suitable
for most cleaning.
12. After marking electrical connections, spliced conductors should
be turned upward and pushed carefully up into outlet box. The
wires should be spread apart with the grounded conductor and
the equipment-grounding conductor on one side of the outlet
box.
13. Electrical diagrams are reference only. Light Kits that are not
packed with the fan must be CUL Listed and marked suitable for
use with the model fan you are installing. Switches must be CUL
General Use Switches. Refer to the Instructions packaged with
the light kits and switches for proper assembly.
14. WARNING: To reduce the risk of personal injury, do not bend
the blade brackets (also reered to as flanges) during assembly
or after installation. Do not insert objects in the path of blades.

52" RenewTM Designer | 5
TOOLS REQUIRED
PACKAGE CONTENTS
• Philips screw driver
• Blade screw driver
• 11mm wrench
• Step ladder
• Wire cutters
Unpack your fan and check the contents. You should have the following items:
A. Fan blades (5)
B. Ceiling mounting bracket
C. Canopy decoration ring
D. Canopy
E. Canopy Cover
F. Ball/downrod assembly
G. Coupler cover
H. Fan motor assembly
I. 17W LED Light Kit
J. Blade brackets with pre-installed
mounting screws (5)
K. Package hardware:
1) Safety cable hardware:
screw (1), flat washer (1)
2) Gasket
3) Pull chains and fobs (1)
4) Balancing Kit
5) Blade attachment hardware:
screws (15), washers (15)
L. Glass shade
M. Remote package
1) Receiver
2) Wall transmitter
b
d
f
j
k
a
h
i
e
c
g
l
m

| KICHLER.COM
6
Outlet box
Provide strong
support
Recessed
outlet box Ceiling
mounting plate
Outlet box
Outlet box
ANGLED CEILING
MAXIMUM 22°
ANGLE
MOUNTING OPTIONS
If there is not an existing UL (cUL for Canadian Installation) listed
mounting box, then read the following instructions. Disconnect the
power by removing fuses or turning o circuit breakers.
Secure the outlet box directly to the building structure. Use
appropriate fasteners and building materials. The outlet box and its
support must be able to fully support the full weight of the fan (up
to 50 lbs). Do not use plastic outlet boxes.
Figures 1, 2, and 3 are examples of dierent ways to mount the
outlet box.
NOTE: If you are installing the ceiling fan on a sloped (vaulted)
ceiling, you may need a longer downrod to maintain proper
clearance between the tip of the blade and the ceiling. A minimum
clearance of 12” is suggested for optimal operation.
NOTE: Depending on the location you have selected for
installation, you may need to purchase and install a “Joist Hanger”
for the support of the outlet box. Make sure the joist hanger you
purchase has been designed for use with ceiling fans. (Fig. 4)
Fig. 2
Fig. 1
Fig. 3
Fig. 4

52" RenewTM Designer | 7
HANGING THE FAN
REMEMBER to turn o the power before you begin.
To properly install your ceiling fan, follow the steps below.
NOTE: This ceiling fan is supplied with two types of hanging
assemblies; the standard ceiling installation using the downrod with
ball and socket mounting and the “close-to-ceiling” installation. The
“close-to-ceiling” installation is recommended in rooms with less
than 8-feet ceilings or in areas where additional space is desired from
the floor to the fan blades.
CUL Listed
e
lectrical box
Ceiling
mounting
bracket
Mounting screws
(supplied with electrical box
)
Washer
120V wires
Fig. 5

| KICHLER.COM
8
HANGING THE FAN
Standard Ceiling Installation
Step 1. Pass the 120-volt supply wires through the center hole in the
ceiling hanger bracket as shown in Fig. 5.
Step 2. Secure the hanger bracket to the ceiling outlet box with the
screws and washers provided with your outlet box.
Step 3. Remove the hitch pin, lock pin and set screws from the top of the
motor assembly.
Step 4. Route wires exiting from the top of the fan motor through the
coupler cover, canopy cover, canopy, decoration ring and then through
the ball/downrod. (Fig. 6)
Step 5. Align the holes at the bottom of the downrod with the holes
in the collar on top of the motor housing (Fig. 6). Carefully insert the
hitch pin through the holes in the collar and downrod. Be careful not
to jam the pin against the wiring inside the downrod. Insert the locking
pin through the hole near the end of the hitch pin until it snaps into its
locked position, as noted in the circle inset of Fig. 6.
Step 6. Tighten two set screws on top of the fan motor firmly. (Fig. 6)
Step 7. Place downrod ball into the hanger bracket socket. (Fig 7)
Fig. 6
Fig. 7
Registration slotCheck tab
Locking pin
Set screws
Hitch pin
Ceiling canopy
Decoration ring
Coupler cover
Downrod
Cross pinHanger ball

52" RenewTM Designer | 9
Fig. 7
HANGING THE FAN
Close-to-Ceiling Installation
Step 1. Pass the 120-volt supply wires through the center hole in the
ceiling hanger bracket as shown in Fig. 8.
Step 2. Secure the hanger bracket to the ceiling outlet box with the
screws and washers provided with your outlet box.
Step 3. Remove three of the six screws and lock washers (every
other one) from the collar of top motor (Fig. 9)
Step 4. Place the ceiling canopy with decoration ring and the
gasket over the collar at the top of the motor. Align the mounting
holes with the holes in the motor and fasten using the screws and
lock washers provided. (Fig. 9)
Step 5. Tighten the mounting screws securely. (Fig. 9)
WARNING: Failure to completely tighten the three screws in step 5
could result in fan loosening and possibly falling.
Step 6. Hang the fan on the hook of the hanger bracket. Be certain
that the canopy is fully locked into hook as shown in Fig. 10. This will
allow you to make the electrical connections.
Ceiling mountin
g
bracket
Canopy
Hook
Fig. 8
Fig. 9
Screws and Lock
washers(3 of 6 places)
Canopy
Gasket
Collar
Decoration ring

| KICHLER.COM
10
INSTALLATION OF SAFETY SUPPORT
(Required for Canadian installation ONLY)
A safety support cable is provided to help prevent the ceiling fan
from falling, please install it as follows.
Step 1. Attach the provided wood screw and washers to the ceiling
joist next to the mounting bracket but do not tighten. (Fig. 10)
Step 2. Adjust the length of the safety cable to reach the screw and
washers by pulling the extra cable through the cable clamp until the
overall length is correct, put the end of the cable back through the
cable clamp, forming a loop at the end of the cable. Tighten the cable
clamp securely. Now, put the loop in the end of the safety cable over
the wood screw securely.
NOTE: Although the safety support cable is required for Canadian
installations only. It’s a good idea to make the attachment with
any installation.
Fig. 10
Hanger bracket
Safety cable
Attach safety cable
to ceiling joist with
screw
WARNING: To avoid possible electrical shock, be sure you have
turned o the power at the main circuit panel.
Follow the steps below to connect the fan to your household wiring.
Use the wire connecting nuts supplied with your fan. Secure the
connector with electrical tape. Make sure there are no loose wire
strands or connections.
Step 1. Insert the receiver into the ceiling mounting bracket with
the flat side of the receiver facing the ceiling. (Fig. 11) For best
performance, make sure the Black Antenna, on the end of the
receiver, remains extended and not tangled with any of the electrical
wires.
ELECTRIC CONNECTIONS
Ceiling mounting
bracket
Receiver
Fig. 11

52" RenewTM Designer | 11
Step 2. Motor to Receiver Electrical Connections: (Fig. 14) Connect the
black wire from the fan to the black wire marked “TO MOTOR L” on the
receiver. Connect the white wire from the fan to the white wire marked
“TO MOTOR N” on the receiver. Connect the blue wire from the fan to
the blue wire marked “FOR LIGHT” on the receiver. Secure all the wire
connections with the plastic wire nuts provided.
Step 3. (Fig. 14) Receiver to House Supply Wires Electrical Connections:
Connect the black (hot) wire from the ceiling to the black wire marked
“AC in L” from the receiver. Connect the white (neutral) wire from the
ceiling to the white wire marked “AC in N” from the receiver. Secure the
wire connections with the plastic wire nuts provided.
Step 4. (Fig. 14) If your outlet box has a ground wire (green or bare
copper) connect it to the fan ground wires; otherwise connect the
hanging bracket ground wire to the mounting bracket. Secure the wire
connection with a plastic nut (provided). After connecting the wires,
spread them apart so that the green and white wires are on one side
of the outlet box and black and blue wires are on the other side.
Carefully tuck the wire connections up into the outlet box.
Fig. 12
ELECTRIC CONNECTIONS
Outlet box
in the ceiling
Green (or bare)
Green
Green
White
White
White
White
Black
Black
Black
Blue
Blue
Black
Receiver