Kichler Lighting Cottage Grove User manual

Cottage GroveTM
Includes our new
CoolTouchTM Control System
Looks permanent, but goes wherever you go!
U.S. Patent Pending
Kichler®Lighting
7711 East Pleasant Valley Road
P.O. Box 318010
Cleveland, Ohio 44131-8010
Customer Service
866.558.5706
8:30 AM to 5:00 PM EST,
Monday - Friday
A Kichler®Décor™ceiling fan
Designed to coordinate with a popular Kichler Lighting collection.
Instruction Manual

Cottage GroveTM
Includes our new
CoolTouchTM Control System
Looks permanent, but goes wherever you go!
U.S. Patent Pending
Kichler®Lighting
7711 East Pleasant Valley Road
P.O. Box 318010
Cleveland, Ohio 44131-8010
Customer Service
866.558.5706
8:30 AM to 5:00 PM EST,
Monday - Friday
A Kichler®Décor™ceiling fan
Designed to coordinate with a popular Kichler Lighting collection.
Instruction Manual

1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local
electrical codes. Electrical installation
should be performed by a qualified
licensed electrician.
3. WARNING: To reduce the risk of electrical
shock and fire, do not use this fan with any
solid-state fan speed control device.
4. WARNING: To reduce the risk of fire,
electric shock, or personal injury, mount to
outlet box marked "Acceptable for Fan
Support of 22.7 kg (50 lbs.) Or Less"
and use mounting screws provided with
the outlet box. Most outlet boxes
commonly used for the support of light
fixtures are not acceptable for fan support
and may need to be replaced. Due to the
complexity of the installation of this fan, a
qualified licensed electrician is strongly
recommended.
5. The outlet box and support structure must
be securely mounted and capable of
reliably supporting a minimum of 50
pounds. Use only CUL Listed outlet boxes
marked "FOR FAN SUPPORT".
6. The fan must be mounted with a minimum
of 7 feet clearance from the trailing edge of
the blades to the floor.
7. To operate the reverse function on this fan,
press the reverse button while the fan is
running.
8. Avoid placing objects in the path of the
blades.
9. To avoid personal injury or damage to the
fan and other items, be cautious when
working around or cleaning the fan.
10. Do not use water or detergents when
cleaning the fan or fan blades. A dry dust
cloth or lightly dampened cloth will be
suitable for most cleaning.
11. After marking electrical connections,
spliced conductors should be turned
upward and pushed carefully up into outlet
box. The wires should be spread apart with
the grounded conductor and the
equipment-grounding conductor on one
side of the outlet box.
12. Electrical diagrams are reference only.
Light kits that are not packed with the fan
must be CUL Listed and marked suitable
for use with the model fan you are
installing. Switches must be CUL General
Use Switches. Refer to the Instructions
packaged with the light kits and switches
for proper assembly.
NOTE: SUITABLE FOR USE WITH SOLID-
STATE SPEED CONTROLS.
1. SAFETY RULES
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT FAN TO
OUTLET BOX MARKED "ACCEPTABLE FOR FAN
SUPPORT". WARNING
TO REDUCE THE RISK OF PERSONAL INJURY,
DO NOT BEND THE BLADE BRACKETS (ALSO
REFERRED TO AS FLANGES) DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT
INSERT OBJECTS IN THE PATH OF THE BLADES.
1

2
3. PACKAGE CONTENTS
Unpack your fan and check the contents. You
should have the following items:
Philips screw driver
Slot screw driver
11 mm wrench
Step ladder
Wire cutters
2. TOOLS AND MATERIALS REQUIRED
Cottage GroveTM
a. Fan blades (5)
b. Mounting bracket
c. Canopy
d. Ball/downrod assembly (1)
& extra downrod (1)
e. Coupling cover
f. Fan assembly
g. Decorative arm
h. Upper glass shade
I. Set of blades bracket (5)
j. Mountiong plate
k. Light kit
l. Bottom Glass shade
m Decorative plate
n Finial
o Bulb
p Mounting plate
q Receiver +7 wire nuts
r CoolTouchTM Control System
s Package hardware
1) Mounting hardware:
wood screws (2), flat washers(2),
screws(2),wire nuts(4)
2) Blade attachment hardware:
screws (16), flat washers(16),
fiber washers(16)
3) Blade bracket hardware:
screws (1)
4) Safety cable hardware:
wood screw, spring washer, flat washer
5) Light kit hardware
manual nut (1) , silicon washer(1) ,
metal washer(1)
6) Balance kit
q
r
a
b
c
d
e
f
g
h
i
j
s
p
o
n
m
k
l

3
4. MOUNTING OPTIONS
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 50 lbs). Do
not use plastic outlet boxes.
Figures 1,2 and 3 are examples of different
ways to mount the outlet box.
NOTE: You may need a longer downrod to
maintain proper blade clearance when
installing on a steep, sloped ceiling. (Fig. 3)
To hang your fan where there is an existing
fixture but no ceiling joist, you may need an
installation hanger bar as shown in Fig 4.
Outlet box
Provide strong
support
Recessed
outlet box Ceiling
mounting
plate
Outlet box
Fig. 1
Fig. 3
Fig. 4
Outlet box
Fig. 2
If there isn't an exsiting UL ( CUL for Canadian
Installation) listed mounting box, then read the
following instructions. Disconnect the power by
removing fuses or turning off circuit breakers.

4
Cottage GroveTM
5. HANGING THE FAN
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
Step 2. Secure the hanger bracket to the
ceiling outlet box using screws and washers
provided. (Fig. 6)
Step 3. Remove hanger ball from downrod
assembly by loosening set screws, removing
the cross pin, and sliding ball off the rod. (Fig. 7)
Step 4. Loosen the two set screws and
remove the hitch pin and lock pin from the top
coupling of the motor assembly. (Fig. 8)
Step 1. Remove the fan motor and housing
assembly from the protective plastic bag.
Place the fan assembly into the lower pad
with the bottom of the motor facing up.(The
lower foam pad serves as a holder for the
fan during the first stages of assembly).
Remove the plastic motor shipping blocks
and discard. (Fig. 5)
Step 5. Place the upper glass bowl on the fan
assembly and tighten it to the mounting plate
with screws provided. (Fig. 8)
Step 6. Carefully feed fan wires up through the
downrod. Thread the downrod onto the motor
coupling until the hitch pin holes are aligned.
Next, replace hitch pin and lock pin, and
tighten both set screws.(Fig. 9)
Fig. 7
Fig. 5
Fig. 6
Fig. 8
Fig. 9
Downrod
Cross pin
Hanger
ball Set screw
CUL listed
electrial box
Mounting bracket
Mounting screw 120V wires
Washer
Fan housing
Screw
shipping block
Hitch pin
Set screw
Lock pin
Downrod
Mounting plate
Screw
Bulb
Upper glass bowl

5
Fig. 10
Fig. 11
Registration slot
Downrod
Screw
Hitch pin
Lock pin
Coupling cover
Canopy Canopy cover
Decorative arm
Step 7. Slip coupling cover, decorative arm,
canopy cover and canopy onto the downrod.
Carefully reinstall the hanger ball onto the
dowrod. Make sure that cross pin is in the
correct position and the set screw is tight
and the wires are not twisted. (Fig 10)
Step 8. Now lift the motor assembly into
position and place the hanger ball into the
hanger bracket. Rotate until the “Check Tab”
has dropped into the “Registration Slot” and
seats firmly. (Fig. 11) The entire motor
assembly should not rotate if this is done
correctly.

6
Cottage GroveTM
6. INSTALLATION OF SAFETY SUPPORT
( For Canadian Installation ONLY )
Fig. 12
Fig. 13
Fig. 14
An additional safety support is provided to
prevent the fan from falling. Secure the safety
cable to the ceiling joist with screw and
washer, as illustrated in Figure 12.
7. MAKE THE ELECTRIC CONNECTIONS
Code switch
Receiver
Hanger
bracket
Battery Compartment
Hanger bracket Safety cable
WARNING: To avoid possible electrical
shock, be sure electricity is turned off at the
main fuse box before wiring.
NOTE: The CoolTouchTM Control System is
equipped with 16 code combinations to
prevent possible interference from or to other
remote units. The frequency switches on your
receiver and transmitter have been preset at
the factory. Please recheck to make sure the
switches on the transmitter and receiver are
set to the same position, any combination of
settings will operate the fan as long as the
transmitter and receiver are set to the same
position. (Fig. 13)
Step 2. (Fig. 14) Motor to Receiver Electrical
Connections: Connect the black wire from the
fan to black wire marked "TO MOTOR L" from
the receiver. Connect the white wire from
the fan to the white wire marked "TO MOTOR
N" from the receiver. Connect the blue wire
from the fan to the blue wire marked "For
Bottom Light" from the receiver. Connect the
orange wire from the fan to the orange wire
marked “For Upper Light” from the receiver.
Secure all the wire connections with the plastic
wire nuts provided. (Fig. 15 on next page)
Step 1. Insert the receiver into the mounting
bracket, and keep flat in opposition of ceiling.
(Fig. 14)

7
Fig. 15
Fig. 16
Step 1. Tuck connections neatly into ceiling
outlet box.
NOTE: adjust the canopy screws as necessary
until the canopy and canopy cover are snug.
(Fig.16)
Note: Fan must be installed at a maximum
distance of 30 feet from the transmitting unit for
proper signal transmission between the
transmitting unit and the fan's receiving unit.
8. FINISHING THE INSTALLATION
Step 2. Slide the canopy up to ceiling and
onto the two screws on hanger bracket.
Rotate the canopy clockwise and tighten both
screws.
Step 3. Receiver to House Supply Wires
Electrical Connections: Connect the black
(hot) wire from the ceiling to the black wire
marked "AC in L" from the receiver. Connect
the white(neutral) wire from the ceiling to the
white wire marked "AC in N" from the Receiver.
Secure the wire connections with the plastic
wire nuts provided. (Fig. 15)
Step 4. If your outlet box has a ground wire
(green or bare copper) connect it to the fan
ground wires; otherwise connect the hanging
bracket ground wire to the mounting bracket.
Secure the wire connection with a plastic nut
provided. After connecting the wires, spread
them apart so that the green and white wires
are on one side of the outlet box and black
and blue wires are on the other side.
Carefully tuck the wire connections up into
the outlet box. (Fig. 15)
Canopy cover
Canopy
Screw
Hanger bracket
Outlet box
white (neutral)
Orange
(For upper light)
Outlex box
Black (hot)
Black("AC" IN L")
Receiver
Black ("to motor L")
Blue (for bottom light)
Orange
(For upper light)
Black (motor)
White (neutral)
Green or bare
Copper (ground)
White("to motor N")
Ground -(Connect to
White("AC IN N")
(green) ground wire on
if no house ground
hanger bracket
wire exists)
Blue (for bottom light)
Warning: Make sure the “Check Tab” at the
bottom of the hanger bracket is properly seated
in the “Registration Slot” on the side of the
hanger ball before attaching the canopy to the
bracket. To seat the “Check Tab” improperly
could damage the electrical wires when to ceil-
ing fan blade direction is changed while the fan
is running.
CAUTION: All set screws must be checked and
retightened where necessary.

8
Cottage GroveTM
9. ATTACHING THE FAN BLADES
Fig. 17
Fig. 19
Fig. 18
10. INSTALLATING THE MOUNTING PLATE
Step 1 Attach the blade to the blade bracket
using the screws, washers and fiber washers
as shown in Figure 17. Start screw into
bracket. Repeat for the two remaining screws.
1. Remove the 1 of 3 screws from the
mounting ring and loosen the other 2 screws.
(Do not remove)
2. Place the key holes on the mounting plate
over the 2 screws previously loosened from
the mounting ring, turn mounting plate until it
locks in place at the narrow section of the key
holes. Secure by tightening the 2 screws
previously loosened and the one previously
removed. (Fig. 19)
Step 2. Make sure the blade is straight and
tighten each screw.
Step 3. Fasten blade assembly to motor using
"pre-installed" mounting screws in the blade
bracket . (Fig. 18)
Blade
Screw
Metal washer
Blade bracket
Fiber washer
Blade bracket
Blade
Screw
Mounting plate
Mounting ring
Screw