Kichler Lighting Highland Manor User manual

Highland ManorTM
Includes our new
CoolTouchTM Control System
Looks permanent, but goes wherever you go!
U.S. Patent Pending
Kichler®Lighting
7711 East Pleasant Valley Road
P.O. Box 318010
Cleveland, Ohio 44131-8010
Customer Service
866.558.5706
8:30 AM to 5:00 PM EST,
Monday - Friday
A Kichler®Décor™ceiling fan
Designed to coordinate with a popular Kichler Lighting collection.
Instruction Manual

1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2.
3. WARNING: To reduce the risk of electrical
shock and fire, do not use this fan with any
solid-state fan speed control device.
4. WARNING: To reduce the risk of fire,
electric shock, or personal injury, mount to
outlet box marked "Acceptable for Fan
Support"
and use mounting screws provided with
the outlet box. Most outlet boxes
commonly used for the support of light
fixtures are not acceptable for fan support
and may need to be replaced. Due to the
complexity of the installation of this fan, a
qualified licensed electrician is strongly
recommended.
5. The outlet box and support structure must
be securely mounted and capable of
reliably supporting a minimum of 50
pounds. Use the outlet boxes marked
"FOR FAN SUPPORT".
6. The fan must be mounted with a minimum
of 7 feet clearance from the trailing edge of
the blades to the floor.
7. To operate the reverse function on this fan,
press the reverse button while the fan is
running.
8. Avoid placing objects in the path of the
blades.
9. To avoid personal injury or damage to the
fan and other items, be cautious when
working around or cleaning the fan.
10. Do not use water or detergents when
cleaning the fan or fan blades. A dry dust
cloth or lightly dampened cloth will be
suitable for most cleaning.
11. After marking electrical connections,
spliced conductors should be turned
upward and pushed carefully up into outlet
box. The wires should be spread apart with
conductor of a fan identified as grounded
condutor to be connected to a grounded
conductor of power supply,conductor to be
connected to an ungrounded conductor of
power supply,conductor of fan identified for
equipment grounding to be connected to an
equipment-grounding conductor.
12. Electrical diagrams are for reference only.
Light kits that are not packed with the fan
must be marked suitable for use with the
model fan you are installing.Refer to the
Instructions packaged with the light kits and
switchesI for proper assembly.
NOTE: NOT SUITABLE FOR USE WITH SOLID-
STATE SPEED CONTROLS.
1. SAFETY RULES
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT FAN TO
OUTLET BOX MARKED "ACCEPTABLE FOR FAN
SUPPORT".
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY
DO NOT BEND THE BLADE BRACKET WHEN
INSTALLING THE BRACKETS, BALANCING THE
BLADES, OR CLEANING THE FAN. DO NOT
INSERT FOREIGN OBJECTS IN BETWEEN ROTAT-
ING FAN BLADES.
1
All wiring must be in accordance with the
National Electrical Code, ANSI/NFPA70-1999
and local electrical codes. Electrical installa-
tion should be performed by a qualified
licensed electrician.

2
3. PACKAGE CONTENTS
Unpack your fan and check the contents. You
should have the following items:
Philips screw driver
Slot screw driver
11 mm wrench
Step ladder
Wire cutters
2. TOOLS AND MATERIALS REQUIRED
Highland ManorTM
a. Canopy (1)
b. Canopy Décor (1)
c. Mounting Bracket (1)
d. Ball / Downrod Assembly (1)
& Extra Downrod (1)
e. Rod Decoration 2 (1)
f. Rod Decoration 1 (1)
g. Fan Assembly (1)
h. Fan Blades (5)
i. Blade Brackets (5)
j. Mounting Plate (1)
k. Light kit (1)
l. Glass Bowl (1)
m. Receiver + 7 Wire Nuts
n. CoolTouch™ Control System
o. Package Hardware:
1) Mounting hardware:
a. wood screws (2), flat washers(2),
screws(2),wire nuts(4)
2) Blade Attachment Hardware:
a. screws (16), flat washers(16),
fiber washers(16)
3) Blade Bracket Hardware:
a. screws (11)
4) Light kit Hardware:
a. screws (4)
5)Safety Cable Hardware:
a. wood screw (1), spring washer (1),
flat washer (1)
6) Balance Kit (1)
p. Light Kit Hardware
a. manual nut (1), silicon washer (1),
metal washer (1), finial (1)
b
c
o
a
g
d
e
h
i
j
k
l
m
n
f
p

4. MOUNTING OPTIONS
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 50 lbs). Do
not use plastic outlet boxes.
Figures 1,2 and 3 are examples of different
ways to mount the outlet box.
NOTE: You may need a longer downrod to
maintain proper blade clearance when
installing on a steep, sloped ceiling. (Fig. 3)
To hang your fan where there is an existing
fixture but no ceiling joist, you may need a
joist hanging bracket as shown in Fig 4.
Outlet box
Provide strong
support
Recessed
outlet box Ceiling
mounting
plate
Outlet box
Fig. 1
Fig. 3
Fig. 4
Outlet box
Fig. 2
If there isn't an existing UL ( CUL for Canadian
Installation) listed mounting box, then read the
following instructions. Disconnect the power by
removing fuses or turning off circuit breakers.
3

4
Highland ManorTM
5. HANGING THE FAN
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
Step 2. Secure the mounting bracket to the
ceiling outlet box using screws and washers
provided with the outlet box. (Fig. 6)
Step 4. Loosen the two set screws and
remove the hitch and lock pin from the
motor coupling assembly. (Fig. 8)
Step 1. Remove the fan motor and housing
assembly from the protective plastic bag
and take the lower Styrofoam packing pad
out of the carton. Place the Styrofoam pad
on the floor, then place the fan assembly
into the Styrofoam pad with the bottom of
the motor facing up. (The Styrofoam pad
serves as a holder for the fan during the first
stages of assembly). Remove the plastic
motor shipping blocks and discard. (Fig. 5)
Step 5. Carefully feed fan electrical wires up
through the downrod. Thread the downrod
onto the motor coupling until the hitch pin
holes are aligned. Next, replace hitch pin and
lock pin, and tighten both set screws. (Fig. 8)
Step 3. Use a screwdriver to loose the cross
pin and removeit from downrod assembly.
Loose the set screw and rotate the hanger
ball off the downrod. (Fig. 7)
Fig. 7
Fig. 5
Fig. 6
Fig. 8
Shipping block
Screw
Supply wires
Downrod
Lock pin Hitch pin
Set Screw
Downrod
Hanger Ball
Cross Pin
Set Screw
Washer
120 V wires
Mounting screw
listed electrial box
Mounting bracket

Fig. 10
Fig. 9
Registration slot
Step 7. Now lift the motor assembly into position
and place the hanger ball into the hanger
bracket. Rotate motor assembly until the “Check
Tab” has dropped into the “Registration Slot”
and seats firmly. (Fig. 10)
NOTE: The entire motor assembly should not
rotate if this is done correctly.
Step 6. Loose the screw on the bottom of the rod
decoration 2. Slip the rod decoration 1, rod deco-
ration 2, canopy décor and canopy onto the
downrod. Reinstall the hanger ball onto the
downrod and make sure the cross pin is in place
and the set screw on hanger ball is tight. Finally
let the rod decoration 2 seat on the top of the rod
decoration 1 and tighten the screw loosened
previously. (Fig. 9)
NOTE: If you choose to use the shorter downrod,
please ignore to install the “rod decoration 2”.
5
Canopy cover
Canopy
Supply wires
Rod Decoration 2
Rod Decoration 1
Screw
NOTE:Please make sure all set screws are in
place and tight before installation the following
steps.

6
Highland ManorTM
6. INSTALLATION OF SAFETY SUPPORT
( For Canadian Installation ONLY )
Fig. 11-2
Fig. 11-1
Fig. 12
Fig. 13
7. MAKE THE ELECTRIC CONNECTIONS
Code switch
Receiver
Hanger
bracket
Battery Compartment
A safety support cable is provided to help prevent
the ceiling fan from failing, please install it as
follows.
Step 1. Attach the provided wood screw and
washers to the ceiling joist next to the mounting
bracket but do not tighten. (Fig. 11-1)
Step 2. Adjust the length of the safety cable to
reach the screw and washers by pulling the extra
cable through the cable clamp until the overall
length is correct, put the end of the cable back
through the cable clamp, forming a loop at the
end of the cable. Tighten the cable clamp
securely. Now, put the loop in the end of the
safety cable over the wood screw and under the
washer. Tighten the wood screw securely. See
Fig. 11-2
WARNING: To avoid possible electrical shock,
be sure the electricity is turned off at the main
circuit breader or fuse box before wiring.
WARNING: If your house wires are different
colors than referenced in this manual, stop
immediately. A professional electriccian is
recommended to determine proper wiring.
NOTE: The CoolTouch™ Control System is
equipped with 16 code combinations to prevent
possible interference from or to other remote
units. The frequency switches on your receiver
and transmitter have been preset at the factory.
Please recheck to make sure the switches on
the transmitter and receiver are set to the same
position, any combination of setting will operate
the fan as long as each switch on the transmitter
and receiver are set to the same opposition.
(Fig. 12) Changing the order of switches on
each switch block, changes the operational
frequency.
Step 1. Insert the receiver into the mounting
bracket, with the flat toward the ceiling. (Fig. 13)
Step 2. Motor to Receiver Electrical Connec-
tions:
NOTE: Make ALL of the following connections
with “Wire Nut” connectors.
Connect the black wire from the fan to black
wire marded “TO MOTOR L” from the receiver.
Connect the white wire from the fan to the white
wire marked “TO MOTOR N” from the receiver.
Connect the blue wire from the fan to the blue
wire marked “FOR Bottom Light” from the
receiver. Place a plastic wire nut on the end of
the Orange Wire coming from the receiver
marked “For Upper Light”. Your ceiling fan is not
equipped with a Upper Light. Secure all the wire
connections with the plastic wire nut provided.
(Fig. 14 on the next page)
Ceiling
Support Brace
Outlet Box
Wood Screw
Flat Screw
Spring Washer
Wood Screw
Safety Cablebolt

Fig. 14
Fig. 15
8. INSTALLING THE CEILING CANOPY
Step 3. Remote Receiver to Outlet Box Electri-
cal Connections: Connect the black
(hot) wire from the ceiling to the black wire
marked "AC in L" from the receiver. Connect
the white(neutral) wire from the ceiling to the
white wire marked "AC in N" from the
Receiver. Secure the wire connections with
the plastic wire nuts provided. (Fig. 14)
Step 4. If your outlet box has a ground wire
(green or bare copper) connect it to the fan
ground wires; otherwise connect the hanging
bracket ground wire to the mounting bracket.
Secure the wire connection with a plastic nut
provided.
NOTE: Carefully tuck the wire connections up
into the outlet box. (Fig. 14)
NOTE: The transmitting unit must be installed
at a maximum distance of 30 feet from the
ceiling fan for proper signal transmission
between the transmitting unit and the fan’s
receiving unit.
WARNING: One last time, make sure the “Check
Tab” at the bottom of the hanger bracket is prop-
erly seated in the “Registration Slot” on the side
of the hanger ball before attaching the canopy to
the bracket. Failure to properly seat the “Check
Tab” could damage the electrical wires when to
ceiling fan blade direction is changed while the
fan is running.
Step 1. Make sure all of the electrical connec-
tions are tucked neatly into ceiling outlet box.
Step 2. Slide the canopy up to ceilng fan and
onto the two screws on hanger bracket. Rotate
the canopy clockwise and tighten the two screws.
Next, while holding the canopy with one hand,
slide the canopy décor over the screws and
rotate clockwise until tight.
NOTE: You may need to adjust the canopy
mounting screws as necessary until the canopy
and canopy cover have a snug fit. (Fig. 15)
Blue(motor)
Black(motor)
White(neutral)
White("to motor N")
Receiver
Ground wire
Orange
(for upper light)
Blue(for bottom light)
Black("to motor L")
White("AC IN N")
Green or bare
copper(ground)
White(neutral)
Black("AC IN L")
Black(hot)
Outlet box
Canopy
Canopy ring
7

8
Highland ManorTM
9. ASSEMBLYING AND ATTACHING
THE FAN BLADES
Fig. 16
Fig. 17
Fig. 18
10. INSTALLATING THE MOUNTING PLATE
Step 1. Remove 1 of the 3 screws on the
mounting ring and loosen the other 2 screws.
Do not remove (the mounting ring located on
the motor shaft).
Step 2. Place the key holes on the mounting
place over the 2 screws previously loosened
and turn the mounting plate until it locks in
place at the narrow end of the key holes.
Secure by tightening the 2 screws previously
loosened and reinsall the one removed. (Fig.
18)
Step 1. Attach the blade to the blade bracket
using the screws, washers and fiber washers
provided. Refer to Fig. 16 as needed. Start
each screw into the bracket. Repeat for the
two (2) remaining screws.
Step 2. Make sure the blade is straight and
tighten each screw until the fiber washer is
slightly compressed and all three screws are
secure.
Step 3. Insert the blade assembly into one of
the slots on the blade bracket ring, align the
mounting holes on the blade bracket with the
mounting holes on the inside of the bracket
ring and insert two (2) mounting screws and
tighten securely. Repeat this procedure for the
remaining four (4) blade assemblies. See Fig.
17 as needed.
Blade Bracket
Blade
Mounting Plate
Screw
Mounting Screw
Mounting Ring
Metal washer
Screw
Silicon washer
Blade Bracket

Fig. 20
Fig. 19
12. INSTALLING THE LIGHT BULB
& GLASS BOWL
11. INSTALLING THE LIGHT KIT
NOTE: Before continuing, make sure the power
is disconnected by turning off the circuit breaker
of removing the fuse at the circuit box.
Step 1. Remove the 3 screws on the mounting
plate.
Step 2. The square wiring connector from the
ceiling fan and the light fixture will only fix
together one way. Match up the same color on
the side of the connector, then push them
together until the snap engages. (Fig. 19)
Step 2. Tuck the connections neatly into the
mounting plate. Align the holes on the mounting
plate and light kit. Tighten the 3 screws removed
previously and make sure all three are tight
securely. (Fig. 19)
Step 1. Install three 40 watt lamp into each of
the three sockets in the light fixture.
Step 2. Slide the glass bowl over the threaded
pipe on the light fixture. Place the silicon
washer, metal washer and thread the manual
nut onto the pipe. Attach and tighten the decora-
tive finial. (Fig. 20)
Step 1. Install three 40 watt lamp into each of
the three sockets in the light fixture.
Step 2. Slide the glass bowl over the threaded
pipe on the light fixture. Place the silicon
washer, metal washer and thread the manual
nut onto the pipe. Attach and tighten the decora-
tive finial. (Fig. 20)
9
Mounting Plate
Light Kit
Glass Bowl
Silicon Washer
Metal Washer
Manual Nut
Finial
Screw
AMP Connection