Kichler Lighting ERIS 337060 User manual

ERIS DOWN ROD HANGER KIT
READ AND SAVE THESE INSTRUCTIONS
337060
U.S. Patent Pending

A. Mounting Bracket .......................................... (1pc)
B. Downrod Assembly ....................................... (1set)
C. Canopy .......................................................... (1pc)
D. Canopy Screw Cover .................................... (1pc)
E. Coupling Cover ............................................. (1pc)
F. Package Hardware ........................................ (1set)
This carton contains the following parts. Please make sure you have everything.
1
Phillips screwdriver
Blade screwdriver
11 mm wrench
Step ladder
Wire cutters
TOOLS AND MATERIALS REQUIRED
A B
D F
C
E

2
ERIS DOWN ROD HANGER KIT
Fig. 1
Fig. 2
Fig. 3
Ceiling joist
Ceiling joist
MOUNTING OPTIONS
Make sure the outlet box you've selected
for mounting your ceiling fan is UL listed
and rated for ceiling fan use.
NOTE: Make sure the electrical power is
turned off before starting. Disconnect at
the main circuit box.
It's very important that the outlet box is
securely installed and will not move or
your ceiling fan will wobble after
installation.
If you need to install a new outlet box,
secure it directly to the building structure
using appropriate fasteners and building
materials.
The outlet box and its support must be
able to fully support the moving weight of
the fan (at least 50 lbs.). Do not use
plastic outlet boxes.
Outlet box
W/Bracket
Ceiling joist
Outlet box
Expandable
joist hanger
Ceiling joist
Outlet box
JOIST MOUNT
BOTTOM FACE MOUNT
SIDE MOUNT

3
Step 1. Assemble the mounting bracket to ceiling
outlet box using the screws and washers
supplied with the outlet box. (Fig. 4)
Step 3. Remove the hanger ball from downrod
assembly by loosening set screw, removing
the pin, and sliding ball off the rod.
Remove the clip and cross pin from the
downrod. (Fig. 6)
Step 2a. For Eris fan installed with mounting
plate cover.
Remove the three (3) mounting screws to release
the mounting plate cover from ceiling fan, then
reinstall the removed screws back to the ceiling
fan. (Fig. 5).
Step 2b. For Eris fan installed without
mounting plate cover.
IMPORTANT: Must install and tighten three (3)
mounting screws, otherwise will destroy your
fan.
Install three (3) mounting screws found in the fan
mounting plate cover hardware bag to the ceiling
fan, and tighten them.(Fig. 5).
Flat Washer
Screw
Mounting Bracket
Outlet Box
Mounting Plate Cover
Screw
Pin Set Screw
Hanger Ball
Cross Pin
Clip
Fig. 4
Fig. 5
Fig. 6

4
ERIS DOWN ROD HANGER KIT
Step 4. Route the black, white, blue wires
and safety cable through the downrod.
Thread downrod into the downrod support
on top of the motor. Install the cross pin by
aligning the holes in the downrod support
with holes in the downrod. Secure cross pin
with clip. Install and tighten the two set
screws to the downrod support. (Fig. 7)
Step 5. Route wires through coupling cover,
canopy screw cover and canopy.（Fig. 8）
Step 6. Carefully reinstall the hanger ball
on the downrod as follows. Route the wires
through the hanger ball. Position the pin
through the two holes in the downrod and
align the hanger ball so the pin is captured
in the groove on the top of the hanger ball.
Pull the hanger ball up tight against the pin.
Securely tighten the set screw in the hanger
ball. A loose set screw could cause fan
wobble. (Fig. 9)
NOTE: All set screws must be checked, and
retightened where necessary, before
installation.
Fig. 7
Fig. 8
Fig. 9
Cross Pin
Clip
Downrod
Downrod Support
Cross Pin
Set Screw
Clip
Canopy
Canopy Screw Cover
Coupling Cover
Pin
Hanger Ball
Set Screw

Step 9. Assemble canopy by rotating key slot
in canopy over shoulder screw in hanger
bracket. Tighten shoulder screw. Fully
assemble and tighten second shoulder screw
that was previously removed. Securely attach
and tighten the canopy screw cover over the
shoulder screws in the mounting bracket
utilizing the keyslot twist-lock feature. (Fig. 12)
Step 8. Now lift the motor assembly into
position and place the hanger ball into the
mounting bracket. Rotate until "Check Tab" has
dropped into the "Registration Slot" and seated
firmly. (Fig. 11) The entire motor assembly
should not rotate.
WARNING: Failure to properly seat the
"Check Tab" can damage the ceiling fan
during operation.
Fig. 10
Fig. 11
Fig. 12
Step 7. Remove one of the two shoulder screws
in the mounting bracket and save for use in
Step 9. Loosen the second shoulder screw
without fully removing it. (Fig. 10)
5
Mounting Bracket
Shoulder Screw
Check Tab Registration Slot
Canopy
Shoulder Screw
Shoulder Screw
Canopy Screw Cover