Kichler Lighting Todo 330025 User manual

TodoTM
330025
Instruction Manual
UL Model #CF101P-56
Includes Wall Control

1
1. SAFETY RULES (READ AND SAVE THESE INSTRUCTIONS)
1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local electrical
codes. Electrical installation should be
performed by a qualied licensed electrician.
3. WARNING: To Reduce The Risk Of Fire Or
Electric Shock, Do Not Use This Fan With
Any Solid-State Speed Control Device. Only
use the remote control provided by ceiling fan
manufacturer.
4. WARNING: To reduce the risk of personal
injury, use only the two steel screws (and
lock washers) provided with the outlet box for
mounting to the outlet box. Most outlet boxes
commonly used for the support of lighting
xtures are not acceptable for fan support of
35 lbs (15.9 kgs) or less and may need to be
replaced, consult a qualied electrician if in
doubt.
5. The outlet box and support structure must
be securely mounted and capable of reliably
supporting a minimum of 35 pounds. Use only
CUL Listed outlet boxes marked “FOR FAN
SUPPORT OF 35 LBS (15.9 KGS ) OR LESS”.
6. The fan must be mounted with a minimum of
10 feet clearance from the trailing edge of the
blades to the oor.
7. Do not operate reversing switch while fan
blades are in motion. Fan must be turned off
and blades stopped before reversing blade
direction.
8. Avoid placing objects in the path of the blades.
9. To avoid personal injury or damage to the fan
and other items, be cautious when working
around or cleaning the fan.
10. Do not use water or detergents when cleaning
the fan or fan blades. A dry dust cloth or lightly
dampened cloth will be suitable for most
cleaning.
11. After marking electrical connections, spliced
conductors should be turned upward and
pushed carefully up into outlet box. The wires
should be spread apart with the grounded
conductor and the equipment-grounding
conductor on one side of the outlet box.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT FAN
TO OUTLET BOX MARKED “ACCEPTABLE
FOR FAN SUPPORT OF 35 LBS (15.9 KGS)
OR LESS”.
WARNING
TO REDUCE THE RISK OF PERSONAL
INJURY, DO NOT BEND THE BLADE
BRACKETS (ALSO REFERRED TO AS
FLANGES) DURING ASSEMBLY OR AFTER
INSTALLATION. DO NOT INSERT OBJECTS
IN THE PATH OF THE BLADES.
WARNING
CHANGES OR MODIFICATIONS TO THIS
UNIT NOT EXPRESSLY APPROVED BY THE
PARTY RESPONSIBLE FOR COMPLIANCE
COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.

2
56” Todo™
2. TOOLS AND MATERIALS REQUIRED
• Phillips screw driver
• Blade screw driver
• 11mm wrench
• Step ladder
• Wire cutters
3. PACKAGE CONTENTS
Unpack your fan and check the contents.
You should have the following items:
a. Ceiling mounting bracket;
Mounting hardware:
J Wood screw (1), Canopy
mounting screw (4),Canopy
mounting lock washer (4)
b. Canopy
c. Ball/downrod assembly
(Pre-installed on the fan)
d. Coupling cover
(Pre-installed on the fan)
e. Fan motor assembly, attached
with hanger bolt, lock washer, at
washer, and split pin
(Pre-installed on the fan)
f. Fan blade/blade arm assemblies (3)
g. Blade hardware: Blade screw
(8); Lock washer (8); Plastic wire
connector (3)
h. Wall mounting control hardware:
Wall control, Control mounting
screw (long x 2), Control
mounting screw (short x 2),
Plastic wire connector (3)
a
b
c
d
e
f
g
h

3
4. MOUNTING OPTIONS
If there isn’t an existing UL (cUL for Canadian
Installation) listed mounting box, then read the
following instructions. Disconnect the power by
removing fuses or turning off circuit breakers.
Secure the outlet box directly to the building structure.
Use appropriate fasteners and building materials. The
outlet box and support structure must be securely
mounted and capable of reliably supporting 35 lbs.
(15.9 kg). Use only UL Listed outlet boxes marked
“Acceptable for Fan Support of 36 lbs. (15.9 kg) or
less”. Do not use a plastic outlet box .
Figures 1, 2, and 3 are examples of different ways to
mount the outlet box.
NOTE: If you are installing the ceiling fan on a sloped
(vaulted) ceiling, you may need a longer downrod
to maintain proper clearance between the tip of the
blade and the ceiling. A minimum clearance of 12” is
suggested for optimal operation.
NOTE: Depending on the location you have selected
for installation, you may need to purchase and install
a “Joist Hanger” for the support of the outlet box.
Make sure the joist hanger you purchase has been
designed for use with ceiling fans. (Fig. 4)
Outlet box
Provide strong
support
Recessed
outlet box Ceiling
mounting
plate
Outlet box
Outlet box
ANGLED CEILING
MAXIMUM 30°ANGLE
Fig. 4
Fig. 3
Fig. 2
Fig. 1

4
56” Todo™
ll
ll
a
5. INSTALLING THE MOUNTING BRACKET
REMEMBER to turn off the power before you begin.
To properly install your ceiling fan,
follow the steps below.
Step 1. Pass the 120 volt supply wires from the
ceiling outlet box through the center of the ceiling
mounting bracket.
Step 2. Attach the ceiling mounting bracket to the
outlet box using the screws and washers included
with the outlet box. (Fig. 5)
Fig. 5
6. INSTALLATION OF SAFETY SUPPORT
(Required for Canadian installation ONLY)
A safety support cable is provided to help prevent the
ceiling fan from falling, please install it as follows.
Step 1. Attach the provided wood screw and washers
to the ceiling joist next to the mounting bracket but do
not tighten.
Step 2. Adjust the length of the safety cable to reach
the screw and washers by pulling the extra cable
through the cable clamp until the overall length is
correct, put the end of the cable back through the
cable clamp, forming a loop at the end of the cable.
Tighten the cable clamp securely. Now, put the loop
in the end of the safety cable over the wood screw
securely. (Fig. 6)
NOTE: Although the safety support cable is required
for Canadian installations only. It’s a good idea to
make the attachment with any installation.
Fig. 6

5
Black
Black
Black
White
Green
White
7. ELECTRICAL CONNECTIONS
WARNING: To avoid possible electrical shock, be sure
you have turned off the power at the main circuit panel.
Step 1. Connect the ground conductor of the 120-Volt
supply (this may be a bare wire or a wire with green
colored insulation) to the green ground leads of the fan.
Step 2. Connect the fan motor white wire to the supply
white wire using a wire connecting nut.
Step 3. Connect the fan motor black wire to the supply
black wire using a wire connecting nut.
Step 4. After connecting the wires, spread them apart
so that the green and the white wires are one side of the
outlet box and the black wire is on the other side.
Step 5. Turn the wire connecting nuts upward, and
carefully push the wiring into the outlet box. (Fig. 7)
Fig. 8
Fig. 7
8. ATTACH THE CANOPY
Step 1. Align the locking slots of the ceiling canopy
with the two screws in the mounting bracket . Push
up to engage the slots , and turn clockwise to lock the
canopy in place.
Step 2. Firmly tighten the two mounting screws with
lock washer.
Step 3. Install the remaining two mounting screws into
the holes in the canopy and tighten rmly. (Fig. 8)

6
56” Todo™
Fig. 9
9. ATTACHING THE FAN BLADE/
BLADE ARM ASSEMBLIES
Step 1. Move the coupler cover to the top of the
downrod, then position the blade assembly on the
motor so the mounting screw holes align with the
threaded holes.
Step 2. Turn the screw into the hole but do not
completely tighten . Make sure the second hole in
the blade assembly aligns with a hole in the motor
housing.
Step 3. Install a second screw in the blade
assembly in the same manner.
Step 4. Repeat for the remaining blades.
Step 5. Tighten all screws. (Fig 9)
10. REPLACE THE DOWNROD
Step 1. Loosen the set screw in the ball and slide down
to remove the support pin, set washer, lock washer and
green ground wire from the top of the downrod.
Step 2. Remove and save the screw, green ground
wire and washer from the top of the downrod
Step 3. Remove the canopy and coupler cover.
Step 4. Loosen and remove the Hanger bolt, lockwashers
and Hexagonal nut on the coupler and remove downrod.
Step 5. Install new downrod using the hardware removed
in steps 1 through 4.
NOTE: Make sure the mounting screws are securely
tightened.
Fig. 10

7
11. TROUBLESHOOTING
Problem
Fan will not start.
Fan sounds noisy.
Fan wobbles.
Remote control
malfunction.
Solution
1. Check circuit fuses or breakers.
2. Check all electrical connections to insure proper contact. CAUTION: Make sure the main
power is OFF when checking any electrical connection.
3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out.
4. Insure the batteries have a good charge.
1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade brackets to the motor are tight.
3. Make sure wire nut connections are not rubbing against each other or the interior wall of the
switch housing. CAUTION: Make sure main power is off.
4. Allow a 24-hour “breaking-in period. Most noise associated with a new fan disappears during
this time.
5. If using an optional light kit, make sure the screws securing the glassware are tight. Make
sure the light bulbs are not touching any other component.
6. Do not connect this fan to wall mounted variable speed control(s). They are not compatible
with ceiling fan motors or remote controls.
7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the
ceiling.
1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the blades. Measure this distance.
Rotate the fan until the next blade is positioned for measurement. Repeat for each blade.
The distance deviation should be equal within 1/8”.
3. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.
4. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can
redistribute the weight and possibly result in smoother operation.
1. Ceiling fans with remote control systems CAN NOT be operated in conjunction with any
other control system EXCEPT a basic On/Off wall switch, if desired.
2. Make sure the frequency dip switches in the transmitter and receiver have identical settings.
3. Make sure the Black Antenna on the receiver is NOT tangled with any other electrical wires
and is extended around the inside of the ceiling canopy.
12. SPECIFICATIONS
Fan size Speed Volts Amps Watts RPM CFM CFM/W N.W. G.W. C.F.
56”
1
120
0.799 95.1 318 10642 112
8.3
kgs
9.3
kgs 1.52’
2 0.733 66.1 253 8497 129
3 0.528 33.0 168 5677 172
4 0.392 18.2 117 4130 227
These are approximate measurements. They do not include data for any lamps or xtures attached to the ceiling fan.

Kichler®Lighting
7711 East Pleasant Valley Road
P.O. Box 318010
Cleveland, Ohio 44131-8010
Customer Service
866.558.5706
8:30 AM to 5:00 PM EST,
Monday - Friday

TodoTM
330025
Guide d’instructions
Modèle UL nº CF101P-56
Comprend une commande murale