Kichler Lighting KAPONO User manual

52
KAPONO LED FAN

KAPONO
INSTALL THE UP HOUSINGINSTALL THE UP HOUSINGINSTALL THE UP HOUSINGINSTALL THE UP HOUSING
2

10.
11.
NOTE：READ AND SAVE THIS INSTRUCTIONS.
6. Allsetscrewsmustbechecked,andretightenedwhere
necessary,beforeinstallation.
MAKE SURE THE POWER IS OFF AT THE
ELECTRICAL BOX BEFORE YOU ATTEMPT ANY CLEANING
AND MAINTENANCE.
7.
8.
9.
WARNING: DO NOT OPERATE REVERSING SWITCH WHILE FAN
BLADES ARE IN MOTION. FAN MUST BE TURNED OFF AND
BLADES STOPPED BEFORE REVERSING BLADE DIRECTION.

KAPONO
Thetotalweightofthefan
includingallaccessories:20.46LBS
a
b
c
d
e
g
h
i
j
5
4
a. Fanblades(5)
b.Bladelockingplate(5)
c. Canopy&Ceilingmounting
bracket
d.Ball/downrodassembly
e. Couplingcover
f. Uphousing
g.Fanmotorassembly
h.Lightkitplate(NBR,NI,WH
&SBK4pcs)
i. 17WLEDassembly
j. Receiver(1)+wirenut(6)
k. Transmitter
l. Partbagcontents
Bladeattachmenthardware:
Bladescrews1/4”*18mm+SP(10)
Uphousingattachmenthardware
Uphousingscrew1/4”*6.4mm(5)
Lightkitplatescrew(3)
43
2
1
l
5
k
f

18

KAPONO
CUL

KAPONO
Sliptheuphousing,couplingcover,
Up housing

KAPONO

KAPONO

Step1.Fastenthebladelockingplateandbladetothefanmotor
assemblybyusingthetwobladescrews.
Fig. 16
Up housing screw
Up housing
Step1.Fastenthebladelockingplateandbladetothefanmotor
assemblybyusingthetwobladescrews.
Fig. 16
Up housing screw
Up housing
Note:Ensuretheuphousingcovertheedgeofallfiveblades.
INSTALL THE UP HOUSINGINSTALL THE UP HOUSING
Step1.Installtheuphousingtothefanmotorassemblybyusingthe
fiveuphousingscrews.Note:pleasemakesureusingtheright5pcsup
housingscrews.Ifusingbladescrewstoinstalltheuphousingbymistake,
itwilldamagethemotor.
Fig. 15
Fan blade
Fan motor
assembly
Blade locking plate
Blade screw
Note:Wheninstallingtheblades,ensurethesideswith
"THISSIDEUP"facetheceiling.

Fig. 17
KAPONO
2
3
Step1:InstallthelightkitplatetotheLEDassemblybyusingthreelightkitscrews.
Note:Foryourconveniencewehaveincluded4lightkitplatewithdifferentfinish
tohelpbettermatchthefan.pleasechoosethefinishyoulike.
Light kit plate
Light kit plate screw
LED assembly
Fig. 18
Switch box
Light kit plate
LED assembly
Fig. 18
Wire connection
plugs
LED assembly

19
20
21

WARNING:ChemicalBurnHazard.Keepbatteriesawayfromchildren.This
remotecontainsalithiumbuttoncellbattery.Ifaneworusedlithiumbutton/
coincellbatteryisswallowedorentersthebody,itcancausesevereinternal
burnsandcanleadtodeathinaslittleas2hours.Alwayscompletelysecure
thebatterycompartment.Ifthebatterycompartmentdoesnotclosesecurely,
stopusingtheproduct,removethebatteries,andkeepitawayfromchildren.
Ifyouthinkbatteriesmighthavebeenswallowedorplacedinsideanypartof
thebody,seekimmediatemedicalattention.
Fig. 22
KAPONO
22
22
22

25
26
Fig. 23
Fig. 24
Fig. 25
Fig. 26
23
Note: Do not operate reversing switch while fan blades are
in motion. Fan must be turned off and blades stopped
before reversing blade direction.

KAPONO

20
FCC Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.