Kimberly-Clark PROFESSIONAL 47604 User manual

Automatic Soap and Sanitizer
Dispenser Counter Mount
Dispenser Code# 47604
Use of this Dispenser
Not recommended for outdoor installation or in wet environments. Do not attempt to clean the dispenser
with a water jet. Follow the installation and usage instruction. Only use genuine Kimberly-Clark Professional
product refills intended for the specific model. The dispenser can be cleaned using a damp cloth and
detergent, do not use abrasive cleaning products.
These instructions are available at www.kcprofessional.com.
General Safety Information
This dispenser can be used by children over the age of 8 years old and persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, provided they have been given
supervision or instruction concerning use of the dispenser by a person responsible for their safety. Access to
the service area is restricted to persons who have knowledge and practical experience of the dispenser, in
particular as far as safety and hygiene are concerned.
This dispenser is not a toy and shall not be used by children as such. Children shall not perform cleaning or
user maintenance of this dispenser. High-risk individuals are not expected to use this dispenser safely unless
continuous supervision is given
Need more information?
These instructions and additional resources are
available at www.kcprofessional.com.Form 033955 • 4/2022
Lock Washer
Nut
Motor Module
Battery
Compartment
Cover
Battery
Compartment
Base with
Power Cable
Optional Hex Nut
Installation Tool
(P/N 774103)
Soap Discharge Head
with Signal Cable

1. If a 1” hole already exists
on the countertop, go to
step 5.
2. If drilling a new hole, it is
recommended the hole be
away from the faucet,
preferably in the 10 o’clock
or 2 o’clock position.
3. Using a tape measure locate
and mark the center line of the
hole a maximum of 3.5” from
the inside edge of the sink.
4. Drill a 1” diameter hole in the
marked location. Clean the area
around the hole so it is free
of debris.
Important: Use the proper
drill bit for your surface and
use cutting fluid to cool the
bit during drilling.
5. Remove adhesive liner on
the bottom surface of the
soap discharge head.
Dispenser Installation
Note: If drilling of the counter top is
required, be sure to use an approved KC
Installer or other trained professional.
2.
10:00
Faucet
2:00
Ideal Dispensing
Head Placement
Optional Area
of Installation
3.
Sink Rim
Sink
Countertop
Hole
Center
3.5”
4.
1.
Materials Required:
5.
• Phillips Bit
• Cutting Fluid
• 1” Diameter Hole Saw
(Diamond Bit for Granite or Stone)
• Adjustable Wrench
• Clear Silicone Caulk
• Magic Marker

6. Insert the signal cable and
threaded shaft of the soap
discharge head through the
hole in the countertop.
7. Finalize the position of the
soap discharge head and then
press down firmly to secure it.
8. Position the lock washer and
nut on the bottom of the threaded
shaft. Thread the nut and continue
turning until both lock washer and
nut are secure to the underside of
the countertop.
Note: Use the optional hex nut
installation tool in areas where
space is limited.
(Spare Part 774103)
9. Apply a bead of clear silicone
caulk around the perimeter of
the soap discharge head base
after it is secure to the countertop.
7.
Dispenser Installation
6.
8.
10. Orient the motor module
under the threaded shaft for
optimal clearance with the
underside of the sink and any
other obstructions. The motor
module has six (6) possible
positions to connect with the
threaded shaft, at least one
will be optimum.
11. Push the motor module lightly
into the threaded shaft while
rotating it slightly clockwise and
counterclockwise. When the
motor module can no longer
rotate it is fully seated.
10. 1
5
36
2
4
11.
9.

12. While holding the motor module
in place, slide the clip on the
motor module forward to lock
the motor module to the
threaded shaft.
14. Orient the plug on the end of
the signal cable so it is properly
keyed with the connector on the
motor module. While holding the
motor module push the plug into
the connector until fully seated.
15. Attach the battery compartment
back to the back or side walls
under the countertop using the
screws and wall anchors
provided. Position the battery
compartment back no further
than 32” from the motor module.
16. Orient the plug on the end of the
power cable so it’s properly keyed
with the connector on the motor
module. While holding the motor
module push the plug into the
connector until fully seated.
Dispenser Installation
12.
14.
16.
13.
13. Remove the protective cap on
the end of the signal cable.
15.

Battery Installation
1. Load four (4) batteries into the
battery compartment cover
ensuring polarity is correct.
2. Orient the battery compartment
cover with the extension tab on
top and install it into the battery
compartment base.
3. Tighten the two screws on
the battery compartment cover
until secure.
1.
2.
3.
Battery Information
• 4D type 1.5V alkaline batteries required.
• Batteries provided for initial installation.
• Change all 4 batteries at the same time, do not mix types or brand of batteries.
• Please follow the battery insertion instructions ensuring polarity is correctly aligned.
• Used batteries are to be disposed of safely and follow local environmental policy for disposal.
• Do not short circuit the supply terminals of the battery or the dispenser.
• Non-rechargeable batteries are not to be recharged.
• Remove batteries if stowed unused for an extended amount of time.

Power Adapter
1. If the dispenser is running on
battery power, remove the battery
power connector while holding
the motor module.
2. Orient the plug on the end of the
power adapter so it’s properly
keyed with the connector
on the on the motor module.
While holding the motor module
push the plug into the connector
until fully seated.
3. Plug the body of the power
adapter into the closest 110V AC
outlet. Note that the cord is
6 feet long.
1.
2.
3.
Note: Use only Kimberly Clark
Professional Power Adapter #51224

2
1
1
Load New Bottle
Remove Empty Bottle
1. Slip the straw into the underside
of the motor module.
1. Squeeze the release tabs (1)
on the top of the bottle and slide
the bottle down (2) and out of
the motor module.
2. Push the refill bottle up into
the motor module until both
snaps on the bottle are secure.
3. Prime the pump by placing one
hand under the soap discharge
head in order to break the opposing
IR beam to activate the motor.
Repeat until a consistent shot of
foam soap is dispensed.
1.
Snap 1
Snap 2
3.
2.
1.

Notifications
Power On
Whenever power is connected
to the dispenser both the red
and yellow LEDs on the soap
discharge head will flash to
indicate the software version.
The flash pattern will repeat for
30 seconds or until a soap
bottle is installed.
SECONDS
30
Low Battery
When battery power is low,
the red LED on the soap
discharge head will flash red
one time every two seconds.
To resolve this, replace
the batteries.
1x
Every 2
SECONDS
Low Soap
When the amount of soap
remaining is low, the yellow
LED on the soap discharge
head will flash yellow one time
every two seconds. To resolve
this, replace the soap bottle
with a new, full one.
Note: Always replace
with full bottles.
1x
Every 2
SECONDS
Motor Overcurrent
Whenever the current exceeds 1800mA
the dispenser will shut down and the red LED
will illuminate and stay on. To resolve this,
disconnect the power cable, wait 5 seconds,
and plug it back in and activate the dispenser.
If the problem persists, replace the soap bottle
with a new one and repeat the power
cable reset procedure above.
Soap Bottle Installed
Whenever a soap bottle is
properly installed, both the
red and yellow LEDs on
the soap discharge head will
illuminate and stay on
for 10 seconds.
SECONDS
10
Dead Battery
When battery power is
insucient to power the
motor the red LED on the
soap discharge head will
flash red two times every
second. To resolve this,
replace the batteries.
2x
Every
SECOND
Out of Soap
When there is no soap
remaining the yellow LED
on the soap discharge head
will flash yellow two times
every second. To resolve this,
replace the soap bottle
with a new, full one.
Note: Always replace
with full bottles.
2x
Every
SECOND

Legal
®/™ Trademarks of Kimberly-Clark Worldwide, Inc. or its aliates. © KCWW
®/™ Marques de commerce de Kimberly-Clark Worldwide, Inc. ou de ses filiales. © KCWW
Made in CHINA / Fabriqué en CHINA / Fabricado en los CHINA
Distributed in the U.S. by Kimberly-Clark Global Sales, LLC, Roswell, GA 30076-2199
Distributed in Canada by Kimberly-Clark Inc., Mississauga, Ontario L5B 3Y5
Americans with Disabilities Act (For use in U.S. only): Title III of the Americans with Disabilities Act (“ADA”) governs,
in detail, the placement and operation of dispensers. You should ensure that your mounting and use of dispensers
complies with that law as well as the regulations issued under that statute. The mounting suggestions in this
document may or may not fulfill the obligations of the ADA with respect to your facility.
Ley de protección de discapacitados (aplicable sólo en EE.UU.). El Artículo III de la Ley de protección de
discapacitados, ADA (
Americans with Disabilities Act ) regula en detalle la instalación y el funcionamiento de
distribuidoras. Asegúrese que la instalación y las disposiciones de uso de la distribuidora cumplan con esta ley y
los reglamentos correspondientes derivados de ella. Es posible que las instrucciones de instalación aquí descritas
cumplan o no con las disposiciones de la ADA dependiendo de las características de su construcción.
Loi concernant les Américains handicapés : Le titre III de l’
Americans with Disabilities Act (« ADA ») (Loi
concernant les Américains handicapés) régit, de façon détaillée, l’emplacement et le fonctionnement des boîtes
distributrices. Vous devez veiller à ce que votre méthode de pose et d’utilisation des boîtes distributrices soit
conforme à la loi, de même qu’aux règlements y afférents. Les suggestions relatives à la pose qui figurent dans le
présent document peuvent répondre ou non aux exigences de l’ADA dépendant du type d’installation.