Kipor Sinamaster I G2600 User manual

SINEMASTER
DIGITAL INVERTER GENERATOR
IG2600
IG2600h
WUXI KIPOR POWER CO., LTD.
R
R

PREFACE
Thank you for purchasing our generators.
This manual covers operation and maintenance of the IG2600, IG2600h
generator.
All information in this publication is based on the latest product information
available at the time of approval for printing.
We reserve the right to make changes at any time without notice and without
incurring any obligation.
No part of this publication may be reproduced without written permission.
This manual should be considered a permanent part of the generator and should
remain with it if it is resold.
Pay special attention to statements preceded by the following words;
Failure to properly follow these precautions can result in
property damage, serious injury or DEATH!
Read all labels and the owner's manual before operating
this generator.
Operate only in well ventilated areas. Exhaust gas
contains poisonous carbon monoxide, and can be deadly.
Always stop engine before refueling. Wait 5 minutes
before restarting.
Check for spilled fuel or leaks. Clean and/or repair before
use.
Keep any sources of ignition away from fuel tank, at all
times.
Indicates a strong possibility of severe personal injury or
death if instructions are not followed.
Indicates a possibility of personal injury or equipment
damage if instructions are not followed.
If a problem should arise, or if you have any questions
about the generator, consult an authorized dealer.
Our generators are designed to give safe and dependable
service if operated according to instructions. Read and
understand the Owner's Manual before operating the gen-
erator. Failure to do so could result in personal injury or
equipment damage.
The illustration may vary according to the type.
WARNING
CAUTION
WARNING
WARNING

CONTENTS
1. Safety Instructions
2. Safety Label Locations
3. Component Indentificaction
4. Pre-operation Check
5. Starting the Engine
High altitude operation
6. Generator Use
7. Stopping the Engine
8. Maintenance
9. Transporting/Storage
10. Troubleshooting
11. Specifications
12. Electric diagram
13. Sketch Map
14. APPENDIX
1
3
4
7
10
12
13
21
23
29
31
33
34
35
36

1. SAFETY INSTRUCTIONS
The muffler becomes very hot during operation and
remains hot for a while after stopping the engine. Be
careful not to touch the muffler while it is hot.Let the
engine cool before storing the generator indoors.
The engine exhaust system will be heated during
operation and remain hot immediately after stopping the
engine.To prevent scalding, pay attention to the warning
marks attached to the generator.
Our generators are designed to give safe anddependable
service if operated according to instructions.
Read and understand the Owner's Manual before
operating the generator. Failure to do so could result in
personal injury or equipment damage.
Exhaust gas contains poisonous carbon monoxide.
Never run the generator in an enclosed area.Be sure to
provide adequate ventilation.When installed in ventilated
protection are to be observed.
WARNING
WARNING
WARNING
WARNING
The conditions of generator rated output:
Altitude: 0 m Ambient temperature: 25 Relative humidity: 30%
Ambient modified coefficient: C (Relative humidity 30%)
Note: When the relative humidity is 60%, the modified coefficient is C-0.01
When the relative humidity is 80%, the modified coefficient is C-0.02
When the relative humidity is 90%, the modified coefficient is C-0.03
When the relative humidity is 100%, the modified coefficient is C-0.04
Counting example:
When the rated power of generator is P =5KW, altitude is 1000m, ambient
N
temperature is 35 , relative humidity is 80%, the rated power of generator is:
P=P (C-0.02) = 5 (0.82-0.02) = 4KW
N
Modified coefficient table
of ambient condition power
Ambient temperature ( )
Altitude
(m)
0
500
1000
2000
3000
4000
25
1
0.93
0.87
0.75
0.64
0.54
30
0.98
0.91
0.85
0.73
0.62
0.52
35
0.96
0.89
0.82
0.71
0.6
0.5
40
0.93
0.87
0.80
0.69
0.58
0.48
45
0.90
0.84
0.78
0.66
0.56
0.46
14. APPENDIX
Operate carefully andmake sure usersand others safety.

Gasoline is extremely flammable and explosive under certain conditions.
Refuel in a well ventilated area with the engine stopped.
Keep away from cigarette, smoke and sparks when re-fueling the generator.
Always refuel in a well-ventilated location.
Wipe up spilled gasoline at once.
Restrict application of generator in high-hazard risk to causing fire area.
WARNING
WARNING
Connections for standby power to a building's electrical system must be
made by a qualified electrician and must comply with all applicable laws and
electrical codes. Im-proper connections can allow electrical current from the
generator to back feed into the utility lines. Such back feed may electrocute
utility company workers or others who contact the lines during a power
outage, and when utility power is restored, the generator may explode,burn
or cause fires in the building's electrical system.
WARNING
Always make a pre-operation inspection before you start the engine. You
may prevent an accident or equipment damage.
Place the generator at least 1m(3ft) away from build-ings or other equipment
during operation.
Operate the generator on a level surface.
If the generator is tiled, fuel spillage may result.
Know how to stop the generator quickly and understand operation of all the
controls.Never permit anyone to operate the generator without proper
instructions.
Keep children and pets away from the generator when it is in operation.
Keep away from rotating parts while the generator is running.
The generator is a potential source of electrical shocks when misused; do
not operate with wet hands.
Do not operate the generator in rain or snow and do not let it get wet.
13. SKETCH MAP
IG2600h
IG2600h movement state IG2600h placed state
Fuse

Oil level
Choke lever
Engine switch
Model
Hot caution
2. SAFETY LABEL LOCATIONS
These lables warn you of potential hazards that can cause serious injury. Read
the labels and safety notes and precautions described in this manual carefully.
If a label comes off or becomes hard to read, contact you dealer for a replacement.
Safety caution
12.ELECTRIC DIAGRAM
Sub winding
Main winding
Stepping motor
Charging widning
DC Receptacle
Engine switch
Ignition winding
Trigger winding
Low oil switch
Spark plug
Ignition coil
Inverter unit
Smart switch
Single phase
receptacle
Operating indicator
Overload indicator
Low oil indicator
Parallel output
Rectifier bridge

Chock Lever
Fuel Cap Lever
Fuel Filler Cap
Left Side
Maintenance
Cover
Starter Grip
Engine Switch
Control Panel
Spark Plug
Maintenance Cover Muffler
3.COMPONENT IDENTIFICATION
Air Exhauat Hole
Air Intake Hole
11. SPECIFICATIONS
DC output
DC output
Fuse
Phase number
12V-5A
with
Single phase
Model IG2600/IG2600h
Rated frequency (Hz)
Rated voltage (V)
Rated current (A)
Rated output (kVA)
Max. output (kVA)
Phase number
50
230
10.0
2.3
2.6
Single phase
60
240
9.6
Engine
Model Type KG166
Type
Displacement (BorexStroke)
Compression ratio
Rated power [kW/(r/min)]
Ignition system
Spark plug
Starting system
Fuel type
.
Fuel consumption (g/kW h)
Lube oil
Single cylinder, air-cooled4 stroke, OHV, gasoline engine
171cc (66x50mm)
8.5:1
3.3/3600
T.C.I
WR7DC
Recoil starter
Automotive unleaded gasoline
500
CD grade or SAE10W-30, 15W-40
Fuel tank capacity (L)
Continuous running time (hr) (at rated output)
4.6
3
IG2600: 26(57.2) IG2600h: 27.5(60.5)
60
120
19.2
Overall dimension (LxWxH) [mm(in)]
Dry weight [kg(lbs)]
IG2600: 564X317X453 (22.2X12.5X17.8)
IG2600h: 590X330X480 (23.2X13.0X18.9)

Smart Throttle Switch
DC Circuit
Protector
AC Receptacle
Output Indicator Light
Overload Indicator
Light
Ground Terminal
Low Oil Alarm
Indicator Light
Control panel
Is the overload
indicator light ON?
Appliance does not operate:
Is the output indicator light ON?
NO
NO
YES
YES
YES
NO
Take the generator to an
authorized dealer.
Take the generator to an
authorized dealer.
Check the electrical appliance
or equipment for any defects.
Replace the electrical
appliance or equipment
Take the electrical
appliance or equipment to
an electrical shop for repair
Change the fuse.
YES
No electricity at the DC receptacle:
Is DC circuit fuse burnt out ?
Take the generator to an
authorized dealer.
NO
Parallel receptacle

Smart Throttle Switch
OFF:
Note:Smart throttle system does not operate. Engine speed is kept over rated speed.
Parallel
Smart throttle
Engine speed is kept at idle automatically when the electrical appliance is
disconnected and it returns to the proper speed to power of the electrical load
when electrical appliance is connected. This position is recommended to minimize
the fuel consumption while in operation.
receptacle
The parallel cabinet can be connected with the parallel socket when the generator
set needs a increasing of parallel output power.
WARNING
Smart throttle system does not operate effectively, if the electrical appliance
requires big momentary electric power.
When high electrical loads are connected simultaneously, turn the Smart-
throttle switch to the OFF position to reduce voltage vibration.
In DC operation, turn the Smart-throttle switch to the OFF position.
10.TROUBLESHOOTING
When the engine will not start:
Is there fuel in the tank?
Is the engine switch on?
YES
YES
YES
Is there enough oil in the engine?
Is there a spark from
the spark plug?
NO
NO
NO
NO Refill the fuel tank.
Turn the engine switch on.
Add the recommended oil.
Still no
spark
Replace the
spark plug.
Take the generator to an
authorized dealer.
WARNING
Be sure there is no spilled
fuel around the spark pulg.
Spilled fuel may ignite.
To check:
1)Remove the spark plug cap and clean
any dirt from around the spark plug.
2)Remove the spark plug and install the
spark plug in the plug cap.
3)Set the plug side electrode on the cylin-
der head to ground.
4)Pull the recoil starter, sparks should jump
across the gap.
If the engine still does not
start, take the generator to
an authorized dealer.
Is the fuel reaching the
carburetor.

4. PRE-OPERATION CHECK
WARNING
Loosen the cover screw and remove the left side maintenance cover. Remove the
oil filler cap, and wipe the dipstick with a clean rag. Check the oil level by inserting
the dipstick in the filler hole without screwing it in.
If the oil level is below the end of the dipstick, refill the recommended oil up to the
top of the oil filler neck.
1. Check the engine oil level.
WARNING
Using nondetergent oil or 2-stroke engine oil could shorten the engine's
service life.
Use a high-detergent, premium quality 4-stroke engine oil, certified to meet
or exceed U.S. automobile manufacturer's requirements for API Service
Classification SG/SF.
Select the appropriate viscosity for the average temperature in your area.
Be sure to check the generator on a level surface with the engine stopped.
CAUTION
Ambient temperature
-25 to -30
-15 to -40
Engine oil type
10W-30
15W-40
SAE Viscosity Grades
Starter Grip
a. Drain all gasoline from the fuel tank into an approved gasoline container.
b. Turn the engine switch ON, and loosen the carburetor drain screw and drain the
gasoline from the carburetor into a suitable container.
c. With the drain screw loosened remove the spark plug cap, and pull the starter grip
3 to 4 times to drain the gasoline from the fuel pump.
d. Turn the engine switch to the OFF position, and tighten the drain screw securely.
3. Change the engine oil.
4. Remove the spark plug and pour about a tablespoon of clean engine oil into the
Cylinder. Crank the engine several revolutions to distribute the oil, then reinstall
the spark plug.
5.Slowly pull the starter grip until resistance is felt. At this point, the piston is
coming up on its compression stroke and both the intake and exhaust valves are
closed. Storing the engine in this position will help to protect it from internal
corrosion.
e.Reinstall the spark plug cap on the spark plug.
Store and use the oil carefully in order to prevent dust or dirty flowing into the
oil. If oil is overfilled, wipe it up at once.
Never mix different kinds of oil.

Oil rule
Upper Lever
Oil Filler Hole
2.Check the fuel level
WARNING
Gasoline is extremely flammable and is explosive under certain conditions.
Refuel in a well-ventilated area with the engine stopped. Do not smoke or
allow flames or sparks in the area where the engine is refueled or where
gasoline is stored.
Do not overfill the fuel tank (there should be no fuel above the upper limit
mark). After refueling, make sure the tank cap is closed properly and
securely.
Be careful not to spill fuel when refueling. Spilled fuel or fuel vapor may ignite,
If any fuel is spilled, make sure the area is dry before starting the engine.
Avoid repeated or prolonged contact with skin or breathing of vapor. KEEP
OUT OF REACH OF CHILDREN.
Upper Limit
Lower Limit
Use automotive gasoline (Unleaded or lowleaded is preferred to minimize combus
tion chamber deposits).
If the fuel level is low, refuel the fuel tank until the level as specified.
Never use an oil/gasoline mixture or dirty gasoline. Avoid getting dirt, dust or water
in the fuel tank. After refueling, tighten the fuel filler cap securely.
9.TRANSPORTING/STORAGE
To prevent fuel spillage when transporting or during temporary storage, the generator
should be secured upright in its normal operating position, with the engine swith OFF. Turn
the cap lever fully counterclockwise to the "OFF" position.
Gasoline is extremely flammable and explosive undercertain conditions.
Do not smoke or allow flames or sparks in the area.
When transporting the generator:
Do not overfill the tank (there should be no fuel in the filler neck).
Do not operate the generator while it is on a vehicle. Take the generator off the
vehicle and use it in a well ventilated place.
Avoid a place exposed to direct sunlight when putting the generator on a
vehicle. if the generator is left in an enclosed vehicle for many hours, high
temperature in-side the vehicle could cause fuel to vaporize resulting in a
possible explosion. Do not drive on a rough road for an extended period with
the generator on board, if you must transport the generator on a rough road,
drain the fuel from the generator beforehand.
Before storing the unit for an extended period:
1. Be sure the storage area is free of excessive humidity and dust.
2.Drain out the fuel completely.
WARNING
WARNING
Drain Screw
WARNING
Running the engine with insufficient oil can cause serious engine damage.
The Low Oil Alarm System will automatically stop the engine before the oil
level falls below the safe limit. However, to avoid the inconvenience of an
unexpected shutdown, it is still advisable to visually inspect the oil level
regularly.

3.Check the air cleaner.
Check the air cleaner element to be sure it is clean and in good condition.
Loosen the cover screw and remove the left side maintenance cover. Press the
latch tab on the top of the air cleaner body, remove the air cleaner cover, check
the element. Clean or replace the element if necessary.
Fuel Filler Cap
OPEN
Upper Limit Mark
Gasoline containing alcohol
If you decide to use a generator containing alcohol (gasohol), be sure it's octane
rating is at least as high as that recommended by us. There are two types of
gasohol: one containing ethanol, and the other containing methanol. Do not use
gasohol that contains more than 10% ethanol. Do not use gasoline containing
methanol (methyl or wood alcohol) that does not also contain cosolvents and
corrosion inhibitors for methanol. Never use gasoline containing more than 5%
methanol, even if it has cosolvents and corrosion inhibitors.
NOTE
nFuel system damage or engine performance problems resulting from the use
of fuel that contain alcohol is not covered under the warranty. We cannot
endorse the use of fuels containing methanol since evidence of their
suitability is as yet incomplete.
nBefore buying fuel from an unfamiliar station, try to find out if the fuel contains
alcohol. If it does, confirm the type and percentage of alcohol used. If you
notice any undesirable operating symptoms while using a gasoline that
contains alcohol, or one that you think contains alcohol, replace it by a
gasoline that you know does not contain alcohol.
1.Remove the four M5 screws, and remove the muffler protector.
2.Remove the muffler, the spark arrester and the muffler gasket
Spark arrester
Muffler Muffler gasket
Rear cover
Seal strip of rear cover
3.Use a brush to remove carbon deposits from the spark arrester screen.
4.Check the muffler gasket; replace if damaged. Reinstall the muffler gasket, the
spark arrester, the muffler and the muffler protector in the reverse order of removal.

CAUTION
Never run the engine without the air cleaner. Rapid en-gine wear will
result from contaminants, such as dust and dirt, being drawn through the
carburetor, into the engine.
Left Side
Maintenance
Cover
Cover
Screw
Air Cleaner Element
Air Cleaner Cover
The spark plug must be securely tightened.An improperly tightened plug can
become very hot and possibly damage the generator.
Never use a spark plug with an improper heat range.
4.SPARK ARRESTER MAINTENANCE(Equipped type only)
The spark arrester must be serviced every 100 hours to maintain its efficiency.
CAUTION
5.Visually inspect the spark plug. Discard it if the insulator is cracked or chipped.
Clean the spark plug with a wire brush if it is to be reused.
6.Measure the plug gap with a feeler gauge.
The gap should be 0.6-0.7 mm (0.024-0.028in). Correct as necessary by carefully
bending the side electrode.
7.Install the spark plug carefully, by hand, to avoid cross-threading.
8.After a new spark plug has been seated by hand, it should be tightened 1/2 turn
with a wrench to compress its washer.
If a used plug is being reinstalled, it should only require 1 / 8 to 1/4 turn after being
seated.
9.Reinstall the spark plug cap on the spark plug securely.
10.Reinstall the spark plug maintenance cover.
CAUTION
WARNING
If the generator has been running, the muffler will be very hot. Allow it to cool
before proceeding.
Tighten Bolt
Coarse Element
Plug Gap 0.6-0.7mm

Fuel Cap Lever ON
ON
Engine Switch
ON
OFF
5.STARTING THE ENGINE
NOTE
Turn the fuel cap vent lever to the OFF position when transporting generator.
When starting the generator after adding fuel for the first time or after long term
storage, or after running out of fuel, turn the fuel valve lever to the ''ON''
position, then wait for 10 to 20 seconds before starting the engine.
Before starting the engine, disconnect the load from the DC terminals.
NOTE
1.Turn the fuel cap lever fully clockwise to the ON position.
2.Turn the engine switch to the ON position.
Spark Plug Maintenance Cover
Handle Bar
Plug Wrench
Spark Plug Cap
RECOMMENTED SPARK PLUG: WR7DC
3.SPARK PLUG SERVICE
To ensure proper engine operation, the spark plug must be properly gapped and
free of deposits.
1.Remove the spark plug maintenance cover.
2.Remove the spark plug cap.
3.Clean any dirt from around the spark plug base.
4.Use the wrench to remove the spark plug.

Starter Grip
4.Pull the starter grip until resistance is felt, then pull the starter grip briskly toward
the arrow as shown below.
Do not allow the starter grip to snap back, Return it slowly by hand.
Fuse
3.Move the choke lever to the START position.
Chock Lever
START
START
Do not use the choke when the engine is warm or the air temperature is high.
NOTE
CAUTION
Left Side
Maintenance
Cover
Cover
Screw
Element
Air Cleaner Element
Air Cleaner
Cover
Coarse Element
2.AIR CLEANER SERVICE
Do not use gasoline or low flash point solvents for cleaning. They are
flammable and explosive under certain conditions.
A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor
malfunction, service the air cleaner regularly. Service more frequently when
operating the generator in extremely dusty areas.
Fuse
Fuse
WARNING
Do not run generator without air cleaner for causing engine accelerated wear.
CAUTION
1.Loosen the cover screw and remove the left side maintenance cover.
2.Loosen the screw of the air cleaner, and remove the air cleaner cover.
3.Wash the element in a non-flammable or high flash point solvent and dry it
thoroughly.
4.Soak the element in clean engine oil and squeeze out the excess oil.
5.Reinstall the air cleaner element and the cover.
6.Reinstall the left side maintenance cover and tighten the cover screw securely.
Tighten bolt

High altitude operation
At high altitude, the standard carburetor air-fuel mixture will be excessively rich.
Performance will decrease, and fuel consumption will increase.
High altitude performance can be improved by installing a smaller diameter main
fuel jet in the carburetor and readjusting the pilot screws. lf you always operate
the generator at altitudes higher than 1,500 m(5,000 feet) above sea level, have
your authorized dealer perform these carburetor modifications.
Even with suitable carburetor jetting, engine horsepower will decrease
approximately 3.5% for each 305m (1,000 feet) increase in altitude. The affect of
altitude on the horsepower will be greater than this if no carburetor modification
is made.
Operation of the generator at an altitude lower than the carburetor is jetted
for may result in reduced performance,overheating,and serious engine
damage caused by an excessively lean air/fuel mixture.
5. Move the choke lever to the RUN position after the engine warms up.
If the engine stops and will not restart, check the engine oil level before
troubleshooting in other areas.
CAUTION
CAUTION
Left Side
Maintenance
Cover
Cover
Screw
Oil Filler Cap
Upper Level
Oil Filler Cap
1.CHANGING OIL
Drain the oil while the engine is still warm to assure rapid and complete draining.
Engine oil capacity: 0.6L
1.Loosen the cover screw and remove the left side maintenance cover.
2.Remove the oil filler cap.
3.Drain dirty oil into a container thoroughly.
4.Refill with the recommended oil, and check the oil level.
5.Reinstall the left side maintenance cover and tighten the cover screw securely.
Make sure to turn the engine switch and the fuel cap
lever OFF before draining.
CAUTION
Wash your hands with soap and water after handling used oil.
Please dispose of used motor oil in a manner that is compatible with the
environment. We suggest you take it in a sealed container to your local
service station for reclamation. Do not throw it in the trash or pour it on the
ground.
NOTE
Chock Lever
RUN
RUN

,
6.GENERATOR USE
(IEC245DV equivalent)
2
2.
Maximum power is available in the first 30 minutes. For continuousoperation,
do not exceed the rated power. In either case, the total wattage of all
appliances con-nected must be considered.
Do not exceed the current limit specified for any one receptacle.
Do not connect the generator to a household circuit. This could cause the
damage to the generator or to electrical appliances in the house.
Do not modify or use the generator for other purposes than it is intended for.
Also observe the following when using the generator.
Do not connect an extension to the exhaust pipe.
When an extension cable is required, be sure to use a tough rubber
sheathed flexible cable.
Limit length of extension cables; less than 60 m for cables if 2.5mm
and less than 100m for cabes of 4.0 mm
Keep the generator away from other electric cables or wires such as
commercial power supply lines.
Electrical equipment(including lines and plug connections) should not be
defective.
CAUTION
WARNING
To prevent electrical shock from faulty appliances, the generator should be
grounded. Connect a length of heavy wire between the generator's ground
terminal and an external ground source.
Connections for standby power to a building's electrical system must be made by
a qualified electrician and must comply with all applicable laws and electrical
codes. improper connections can allow electrical current from the generator to
backfeed into the utility lines. Such backfeed may electrocute utility company
workers or others who contact the lines during a power outage, and when utility
power is restored, the generator may explode, burn, or cause fires in the building's
electrical system.
8.MAINTENANCE
The purpose of the maintenance and adjustment schedule is to keep the generator
in the best operating condition.
Maintenance Schedule
EACH
USE
FIRST
MONTH
OR
10HRS
EVERY 6
MONTHS
OR
100 HRS
EVERY 3
MONTHS
OR
50HRS
EVERY
YEAR
OR
300 HRS
REGULAR SERVICE PE-
RIOD(1) Perform at every
indicated month or operating
hour interval, whichever occurs
first.
ITEM
Engine oil
Air cleaner
Spark plug
Spark arrester
Fuel sediment cup
Valve clearance
Fuel tank and strainer
Fuel line
Check
Change
Check
Clean
Clean-adjust
Clean
Check-adjust
Clean
Check
(2)
(3)
(3)
Every 2 years (Replace if necessary)(3)
(1) Log hours of operation to determine proper maintenance.
(2) Service more frequently when used in dusty areas.
(3) These items should be serviced by an authorized dealer, unless the owner has the
proper tools and is mechanically proficient. See the Shop Manual.
NOTE:
Shut off the engine before performing any maintenance.
If the engine must be run, make sure the area is well ventilated. The exhaust
contains poisonous carbon monoxide gas.
Use genuine parts or their equivalent. The use of replacement parts which are
not of equivalent quality may damage the generator.
WARNING
CAUTION

AC applications
1.Start the engine and make sure the output indicator light(green)comes on.
2.Confirm that the appliance to be used is switched off, and plug in the appliance.
Electrical equipment (including electrical lines and plugs connection) could not
be defective.
The DC receptacle can be used while the AC power is in use. if you use both
at the same time, be sure not to exceed the total power for AC and DC.
NOTE
Overload Indicator
Light (Red)
Output Indicator
Light (Green)
Plug
CAUTION
Be sure that all appliances are in good working order before connecting them
to the generator. If an appliance begins to operate abnormally, becomes
sluggish, or stops suddenly, turn off the generator engine switch immediately.
Then disconnect the appliance, and examine it for signs of malfunction.
3. In order to acquire both the best effect and the maximum service life of the
generator. Usually, the new generator should run 20 hours under 50% load, the
generator may reach the best performance.
Fuel Cap Lever
OFF
3.Turn the cap lever fully counterclockwise to the "OFF" position
Be sure the fuel cap lever, choke and the engine switch are "OFF" when
stopping, transporting and/or storing the generator.
CAUTION

Overload Indicator Light (Red)
Output Indicator Light (Green)
Output and Overload Indicators
The output indicator light(green) will remain ON during normal operating
conditions.
If the generator is overloaded(in excess of 2.6kVA), or if there is a short in the
connected appliance, the output indicator light(greer) will go OFF, the overload
indicator light(red) will go ON and current to the connected appliance will be shut
off.
Stop the engine if the overload indicator light (red) comes ON and investigate the
overload source.
If the oil level indicator light comes on, please check it.
Before connecting an appliance to the generator, check that it is in good order,
and that its electrical rating doe not exceed that of the generator. Then connect
the power cord of the appliance, and start the engine.
When an electric motor is started, both the overload indicator light(red) and the
output indicator light (green) may go on simultaneously. This is normal if the
over-load indicator light(red) goes off after about four (4) seconds. If the overload
indicator light (red) stays on, consult our generator dealer.
NOTE
NOTE
Plug
ON
Engine Switch
ON
OFF
7.STOPPING THE ENGINE
2.Turn the engine switch to the OFF position.
To stop the engine in an emergency, turn the engine switch to the OFF position.
IN NORMAL USE:
1.Switch off the connected equipment and pull the inserted plug.