Kipor Sinemaster IG200 User manual

SINEMASTER
DIGITAL INVERTER GENERATOR
IG2000
IG2000s
IG2000p
WUXI KIPOR POWER CO., LTD.
R
R

PREFACE
Thank you for purchasing our generators.
This manual covers operation and maintenance of the IG2000, IG2000s, IG2000p
generator.
All information in this publication is based on the latest product information
available at the time of approval for printing.
We reserve the right to make changes at any time without notice and without
incurring any obligation.
No part of this publication may be reproduced without written permission.
This manual should be considered a permanent part of the generator and should
remain with it if it is resold.
Pay special attention to statements preceded by the following words;
Failure to properly follow these precautions can result in
property damage, serious injury or DEATH!
Read all labels and the owner's manual before operating
this generator.
Operate only in well ventilated areas. Exhaust gas
contains poisonous carbon monoxide, and can be deadly.
Always stop engine before refueling. Wait 5 minutes
before restarting.
Check for spilled fuel or leaks. Clean and/or repair before
use.
Keep any sources of ignition away from fuel tank, at all
times.
Indicates a strong possibility of severe personal injury or
death if instructions are not followed.
Indicates a possibility of personal injury or equipment
damage if instructions are not followed.
NOTE: Gives helpful information.
If a problem should arise, or if you have any questions about the generator,
consult an authorized dealer.
The generators are designed to give safe and dependable
service if operated according to instructions. Read and
understand the Owner's Manual before operating the gen-
erator. Failure to do so could result in personal injury or
equipment damage.
The illustration may vary according to the type.
WARNING
CAUTION
WARNING
WARNING

The conditions of generator rated output:
Altitude: 0 m Ambient temperature: 25 Relative humidity: 30%
Ambient modified coefficient: C (Relative humidity 30%)
Note: When the relative humidity is 60%, the modified coefficient is C-0.01
When the relative humidity is 80%, the modified coefficient is C-0.02
When the relative humidity is 90%, the modified coefficient is C-0.03
When the relative humidity is 100%, the modified coefficient is C-0.04
Counting example:
When the rated power of generator is P =5KW, altitude is 1000m, ambient
N
temperature is 35 , relative humidity is 80%, the rated power of generator is:
P=P (C-0.02) = 5 (0.82-0.02) = 4KW
N
Modified coefficient table
of ambient condition power
Ambient temperature ( )
Altitude
(m)
0
500
1000
2000
3000
4000
25
1
0.93
0.87
0.75
0.64
0.54
30
0.98
0.91
0.85
0.73
0.62
0.52
35
0.96
0.89
0.82
0.71
0.6
0.5
40
0.93
0.87
0.80
0.69
0.58
0.48
45
0.90
0.84
0.78
0.66
0.56
0.46
15. APPENDIX
--
1. SAFETY INSTRUCTIONS
2. SAFETY LABEL LOCATIONS
3. COMPONENT IDENTIFICATION
4. PRE-OPERATION CHECK
5. STARTING THE ENGINE
High altitude operation
6. GENERATOR USE
7. STOPPING THE ENGINE
8. DOUBLE GENERATORS PARALLEL
9. MAINTENANCE
10. TRANSPORTING/STORAGE
11. TROUBLESHOOTING
12. SPECIFICATIONS
13. ELECTRICAL WIRING DIAGRAM
14. LIGHT KIT
15. APPENDIX
CONTENTS
1
3
5
9
13
16
17
24
26
30
37
39
41
42
44
45

14. LIGHT KIT
Our IG2000s Light kit is designed specifically for use on IG2000 Generator.
Tools required: Phillips Screwdriver
Fittings supplied:
(1) IG2000 Portable Digital Generator
(2) KGE2000Tsi-05100 Light KitAssembly
(3) KGE1000Tsi-05001a Nut
(4) KGE1000Tsi-05002a Threaded screw
(5) KGE2000Tsi-05003 Left Mount Plate of Light Housing
(6) KGE2000Tsi-05004 Right Mount Plate of Light Housing
(7) Screw M5 65 2PCS
(8) Screw M5 16 1PCS
(9) Nut M5 1PC
This is where the Light Kit will be mounted, see IG2000s Assembly Drawing of the Portable
Digital Generator Light Kit.
(1) Remove the screw from the IG2000 Portable Digital Generator and the screws from the
side of the control plate;
(2) Disperse the mount plate of the Light, use screw M5 65 and screw M5 16, then locate
the mount plate of Light Housing on generator. DO NOT TIGHTEN SCREWS.
(3) Use the threaded screw through the Light, left and right mount plate in turn, then lock the
nut.
(4) After adjusting the turnover angular of Light, tighten the avove mentioned of threaded
screw, screw M5 65 and screw M5 16 in turn.
Before energizing the light, be sure to read the Generator Owner's Manual for best operation
and maintenance information, along with the safety precautions. It is recommended that the
light switch be in the OFF position when starting the generator.
MOUNTING INSTRUCTIONS FOR: IG2000s LIGHT KIT
M5 65
M5 65
M5 16
--
1. SAFETY INSTRUCTIONS
To ensure safe operation
WARNING
The generators are designed to give safe and depend-
Read and understand the Owner's Manual before op-
erating the generator. Failure to do so could result in
WARNING
WARNING
able service if operated according to instructions.
personal injury or equipment damage.
Exhaust gas contains poisonous carbon monoxide.
Never run the generator in an enclosed area.
Be sure to provide adequate ventilation.
The muffler becomes very hot during operation and
remains hot for a while after stopping the engine.
Be careful not to touch the muffler while it is hot.
Let the engine cool before storing the generator indoors.
The engine exhaust system will be heated during
operation and remain hot immediately after stopping
the engine.
To prevent scalding, pay attention to the warning marks
attached to the generator.
M5 Nut

IG2000p
--
WARNING
SAFETY INSTRUCTIONS
To ensure safe operation
Gasoline is extremely flammable and explosive under certain conditions.
Refuel in a well ventilated area with the engine stopped.
Keep away from cigarette, smoke and sparks when refueling the
generator, Always refuel in a well-ventilated location.
Wipe up spilled gasoline at once.
WARNING
Always make a pre-operation inspection (page 9) before you start the
engine. You may prevent an accident or equipment damage.
Place the generator at least 1m(3ft) away from buildings or other
equipment during operation.
Operate the generator on a level surface. if the generator is tiled, fuel
spillage may result.
Know how to stop the generator quickly and understand operation of all
the controls. Never permit anyone to operate the generator without proper
instructions.
Keep children and pets away from the generator when it is in operation.
Keep away from rotating parts while the generator is running.
The generator is a potential source of electrical shocks when misused; do
not operate with wet hands.
Do not operate the generator in rain or snow and do not let it get wet.

13. ELECTRICAL WIRING DIAGRAM
--
IG2000 / IG2000s
2. SAFETY LABEL LOCATIONS
These lables warn you potential hazards that can cause serious injury. Read the
labels and safety notes and precautions described in manual carefully.
If a label comes off or becomes hard to read, contact your dealer for a
replacement.
CHOKE HANDLE
LOW OIL ALARM
ENGINE SWITCH

--
SAFETY CAUTION
MODEL
HOT CAUTION
12. SPECIFICATIONS
DC output
DC voltage
Electric circuit breaker
Phase number
12V-8.3A
Available
Single phase
SPECIFICATIONS
Model IG2000/IG2000s/IG2000p
Rated frequency (Hz)
Rated voltage (V)
Rated current (A)
Rated speed (rpm)
Rated output (kVA)
Max. output (kVA)
50
230
7.0
4500
1.6
2.0
60
240
6.7
Engine
Model Type KG158
Type
Displacement (Bore Stroke)
Compression ratio
Rated power[kVA(Hp)/(r/min)]
Rated rotation speed (rpm)
Ignition system
Spark plug
Starting system
Fuel
.
Fuel consumption (g /kW h)
Lube oil
Single cylinder, 4 stroke, vertical, air-cooled, OHV, gasoline engine
105.6ml (58 40mm)
8.5:1
2.2/4500
4500
T. C. I
BOSCH R6 SUF
Recoil starter
Automotive unleaded gasoline
420
CD grade or SAE 10W-30,15W-40
Fuel tank capacity (L)
Continuous running time (hr) (at rated output)
Noise level(zero load~ full load) [dB(A)/7m]
3.7
3.0
61-73 *
Dry weight [kg(lbs)]
IG2000: 22 (48.4) IG2000s: 23.5 (51.7)
IG2000: 549 291 405(21.61 11.46 15.94)
IG2000s: 660 296 431(25.98 11.65 16.97)
60
120
13.3
Overall dimension (L W H) [mm(in)]
NOTE: IG2000 type is basic type; IG2000s type is with light kit; IG2000p type is double generators
parallel type.
*The declared values shall consider uncertainties due to production variation and measurement
procedures.

No electricity at the DC receptacle:
Appliance does not operate:
Is the output indicator light ON?
Is the overload in-
dicator light ON?
Take the generator to an
authorized dealer.
Check the electrical appli-
ance or equipment for any
defects.
Take the generator to an
authorized dealer.
Replace the electrical
appliance or equipment
Take the electrical appli-
ance or equipment to an
electrical shop for repair
Stop and restart the engine.
Take the generator to an
authorized dealer.
Turn the DC circuit protector on. Is DC circuit protect on? NO
YES
DEFECTS
NO DEFECTS
NO
NO
YES
YES
--
3. COMPONENT IDENTIFICATION
ENGINE SWITCH
FUEL CAP HANDLE
CHOKE HANDLE
FUEL FILLER CAP
MAINTENANCE
COVER
CONTROL PANEL
STARTER GRIP
SPARK PLUG
MAINTENANCE
COVER
MUFFLER
AIR EXHAUAT HOLE
AIR INTAKE HOLE

11. TROUBLESHOOTING
To check:
1) Remove the spark plug cap and clean
any dirt from around the spark plug.
2) Remove the spark plug and install the
spark plug in the plug cap.
3) Set the plug side electrode on the cylinder
head to ground.
4) Pull the recoil starter, sparks should jump
across the gap.
When the engine will not start:
Is there fuel in the tank?
NO
Refuel the fuel tank
YES
Is the engine switch on? Turn the engine switch on.
Is the enough oil in the engine? Add the recommended oil.
Is there a spark from
the spark plug?
Replace the
spark plug.
Take the generator to an
authorized dealer.
Still no
spark
YES
YES
NO
NO
NO
Be sure there is no spilled
fuel around the spark plug.
Spilled fuel may ignite.
WARNING
If the engine still does not
start, take the generator to an
authorized dealer.
--
Control panel
EU type
LOW OIL ALARM
INDICATOR LIGHT
SMART-THROTTLE SWITCH
OUTPUT INDICATOR LIGHT
OVERLOAD INDICATOR LIGHT
DC RECEPTACLE
GROUND TERMINAL
DC CIRCUIT PROTECTOR
AC RECEPTACLE

a. Drain all gasoline from the fuel tank into an approved gasoline container.
b. Turn the engine switch ON, and loosen the carburetor drain screw and drain the
gasoline from the carburetor into a suitable container.
c. With the drain screw loosened remove the spark plug cap, and pull the starter grip 3
to 4 times to drain the gasoline from the fuel pump.
d. Turn the engine switch to the OFF position, and tighten the drain screw securely.
e. Reinstall the spark plug cap on the spark plug securely.
3. Change the engine oil .
4. Remove the spark plug and pour about a tablespoon of clean engine oil into the
cylinder. Crank the engine several revolutions to distribute the oil, then reinstall the
spark plug.
5. Slowly pull the starter grip until resistance is felt. At this point, the piston is coming up
on its compression stroke and both the intake and exhaust valves are closed. Storing
the engine in this position will help to protect it from internal corrosion.
Starter grip
--
A type (120V) Aus type
H type A type (240V)
AC RECEPTACLE AC RECEPTACLE
AC RECEPTACLE
AC RECEPTACLE

10. TRANSPORTING STORAGE
To prevent fuel spillage when transporting or during temporary storage, the generator
should be secured upright in its normal operating position, with the engine switch OFF.
The fuel cap vent lever is turned counterclockwise to the OFF position.
Allow the engine to cool well before turning the fuel cap vent lever to the OFF position.
WARNING
When transporting the generator:
Do not overfill the tank (there should be no fuel in the filler neck).
Do not operate the generator while it is on a vehicle. Take the generator off the
vehicle and use it in a well ventilated place.
Avoid a place exposed to direct sunlight when putting the generator on a
vehicle. If the generator is left in an enclosed vehicle for many hours, high
temperature inside the vehicle could cause fuel to vaporize resulting in a
possible explosion.
Do not drive on a rough road for an extended period with the generator on
board. If you must transport the generator on board. If you must transport the
generator on a rough road, drain the fuel from the generator beforehand.
Before storing the unit for an extended period:
1. Be sure the storage area is free of excessive humidity and dust.
2. Drain the fuel.
WARNING
Gasoline is extremely flammable and explosive under certain conditions.
Do not smoke or allow flames or sparks in the area.
SCREW DRIVER
--
Smart throttle
Engine speed is kept at idle automatically when the electrical appliance is disconnected
and it returns to the proper speed to power of the electrical load when electrical
appliance is connected. This position is recommended to minimize the fuel consumption
while in operation.
WARNING
Smart throttle system does not operate effectively, if the electrical appliance
requires the momentary electric power.
When high electrical loads are connected simultaneously, turn the Smart-
throttle switch to the OFF position to reduce voltage vibration.
In DC operation, turn the Smart-throttle switch to the OFF position.
OFF:
Smart-throttle system does not operate. Engine speed is kept over rated speed.
ON
OFF OFF
ON

3.Use a brush to remove carbon deposits from the spark arrester screen.
Inspect the screen for holes, and replace it if necessary.
4.Check the muffler gasket; replace if damaged. Reinstall the muffler gasket, the
spark arrester, the muffler and the muffler protector in the reverse order of removal.
4. PRE-OPERATION CHECK
WARNING
Loosen the cover screw and remove the left side maintenance cover. Remove the oil
filler cap, and wipe the dipstick with a clean rag. Check the oil level by inserting the
dipstick in the filler hole without screwing it in.
If the oil level is below the end of the dipstick, refill the recommended oil up to the top of
the oil filler neck.
1. Check the engine oil level.
WARNING
Using nondetergent oil or 2-stroke engine oil could shorten the engine's service
life.
Running the engine with insufficient oil can cause serious engine damage.
Be sure to check the generator on a level surface with the engine stopped.
WARNING
Caution!
Store and use the oil carefully in order to prevent dust or dirty flowing into the
oil. If oil is overfilled, wipe it up at once.
Never mix different kinds of oil.
Oil is a major factor affecting performance and service life. Use 4-stroke automotive detergent
oil.
Select the appropriate viscosity of oil according to the ambient temperature. Prefer
to "GB/T 11122-1997 Diesel", as follows:
Ambient temperature
-25 to -30
-15 to -40
Engine oil type
10W-30
15W-40

4.SPARK ARRESTER MAINTENANCE(Equipped type only)
If the generator has been running, the muffler will be
very hot. Allow it to cool before proceeding.
The spark arrester must be serviced every 100 hours
to maintain its efficiency.
1.Remove the four 5 mm screws, and remove the muffler protector.
2.Remove the there 6 mm bolts, and remove the muffler, the spark arrester and the
muffler gasket
WARNING
CAUTION
NOTE: The Low Oil Alarm System will automatically stop the engine before the oil level
falls below the safe limit. However, to avoid the inconvenience of an unexpected
shutdown, it is still advisable to visually inspect the oil level regularly.
OIL FILLER HOLE
WARNING
Gasoline is extremely flammable and is explosive under certain conditions.
Refuel in a well-ventilated area with the engine stopped. Do not smoke or
allow flames or sparks in the area where the engine is refueled or where
gasoline is stored.
Do not overfill the fuel tank (there should be no fuel above the upper limit mark).
After refueling, make sure the tank cap is closed properly and securely.
Be careful not to spill fuel when refueling. Spilled fuel or fuel vapor may ignite,
If any fuel is spilled, make sure the area is dry before starting the engine.
Avoid repeated or prolonged contact with skin or breathing of vapor. KEEP
OUT OF REACH OF CHILDREN.
2. Check the fuel level.
Use automotive gasoline (Unleaded or lowleaded is preferred to minimize combustion
chamber deposits).
If the fuel level is low, refuel the fuel tank until the level increased to the specified mark.
Never use an oil/gasoline mixture or dirty gasoline.
Avoid getting dirt, dust or water in the fuel tank.
After refueling, tighten the fuel filler cap seurely.
UPPER LEVEL
OIL FILLER CAP

5. Visually inspect the spark plug. Discard it if the insulator is cracked or chipped.
Clean the spark plug with a wire brush if it is to be reused.
6. Measure the plug gap with a feeler gauge.
The gap should be 0.6~0.7mm (0.024-0.028in). Correct as necessary by carefully bend-
ing the side electrode.
7. Install the spark plug carefully, by hand, to avoid cross-threading.
8. After a new spark plug has been seated by hand, it should be tightened 1/2 turn with
a wrench to compress its washer.
If a used plug is being reinstalled, it should only require 1/8 to 1/4 turn after being
seated.
9. Reinstall the spark plug cap on the spark plug securely.
10. Reinstall the spark plug maintenance cover.
CAUTION
The spark plug must be securely tightened. An improperly tightened plug can
become very hot and possibly damage the generator.
Never use a spark plug with an improper heat range.
Never use a spark plug without damping resistance, or it will cause no AC
output.
0.6-0.7mm
(0.024-0.028 in)
Gasolines containing alcohol
If you decide to use a gasoline containing alcohol (gasohol), be sure it's octane rating is
at least as high as that recommended by us. There are two types of gasohol : one
containing ethanol, and the other containing methanol. Do not use gasohol that contains
more than 10% ethanol. Do not use gasoline containing methanol (methyl or wood
alcohol) that does not also contain cosolvents and corrosion inhibitors for methanol.
Never use gasoline containing more than 5% methanol, even if it has cosolvents and
corrosion inhibitors.
Fuel tank capacity: 3.7 liter (0.97 US gal, 0.81 lmp gal)
UPPER LIMIT MARK
NOTE
Fuel system damage or engine performance problems resulting from the use of
fuels that contain alcohol is not covered under the warranty. We cannot en-
dorse the use of fuels containing methanol since evidence of their suitability is
as yet incomplete.
Before buying fuel from an unfamiliar station, try to find out if the fuel contains
alcohol, if it does, confirm the type and percentage of alcohol used. If you
notice any undersirable operating symptoms while using a gasoline that
contains alcohol, or one that you think contains alcohol, replace it by a gasoline
that you know does not contain alcohol.
FUEL FILLER CAP
RUN

3. SPARK PLUG SERVICE
RECOMMENTDED SPARK PLUG: BOSCH R6 SUF
To ensure proper engine operation, the spark plug must be properly gapped and free of
deposits.
1. Remove the spark plug maintenance cover
2. Remove the spark plug cap.
3. Clean any dirt from around the spark plug base.
4. Use the wrench to remove the spark plug.
SPARK PLUG MAINTENANCE COVER
SPARK PLUG CAP
HANDLE BAR
PLUG WRENCH
3. Check the air cleaner.
Check the air cleaner element to be sure it is clean and in good condition.
Loosen the cover screw and remove the left side maintenance cover.
Press the latch tab on the top of the air cleaner body, remove the air cleaner cover, check
the element. Clean or replace the element if necessary.
CAUTION
Never run the engine without the air cleaner. Rapid engine wear will result
from contaminants, such as dust and dirt, being drawn through the carburetor,
into the engine.
AIR CLEANER ELEMENTS
AIR CLEANER BODY
AIR CLEANER COVER
AIR CLEANER
COVER SCREW
MAINTENANCE COVER
MAINTENANCE COVER
SCREW

2. AIR CLEANER SERVICE
A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor malfunc-
tion, service the air cleaner regularly. Service more frequently when operating the
generator in extremely dirty areas.
1. Loosen the cover screw and remove the left side maintenance cover.
2. Remove the air cleaner cover.
3. Wash the element in a non-flammable or high flash point solvent and dry it thoroughly.
4. Soak the element in clean engine oil and squeeze out the excess oil.
5. Reinstall the main and outer air cleaner elements and the air cleaner cover. Tighten
the cover screw securely.
6. Reinstall the maintenance cover and tighten the cover screw securely.
WARNING
Do not use gasoline or low flash point solvents for cleaning. They are
flammable and explosive under certain conditions.
CAUTION
Never run the generator without the air cleaner, otherwise rapid engine wear
may result.
ELEMENT
AIR CLEANER
COVER SCREW
AIR CLEANER
COVER
MAINTENANCE
COVER SCREW
MAINTENANCE
COVER
AIR CLEANER
BODY
AIR CLEANER
ELEMENTS
5. STARTING THE ENGINE
Before starting the engine, disconnect any load from the AC receptacle.
1.Turn the fuel cap lever fully clockwise to the ON position.
NOTE: Turn the fuel cap vent lever to the OFF position when transporting the generator.
FUEL CAPHANDLE
ENGINE SWITCH
2.Turn the engine switch to the ON position.
ON
ON
OFF
ON

1. CHANGING OIL
Drain the oil while the engine is still warm to assure rapid and complete draining.
1. Loosen the cover screw and remove the left side maintenance cover.
2. Remove the oil filler cap.
3. Drain dirty oil into a container thoroughly.
4. Refill with the recommended oil, and check the oil level.
5. Reinstall the left side maintenance cover and tighten the cover screw securely.
Engine oil capacity: 0.4L (0.42USQT, 0.35LMQT)
Make sure to turn the engine switch and the fuel cap vent lever OFF before
draining.
CAUTION
Wash your hands with soap and water after handing used oil.
NOTE
Please dispose of used motor oil in a manner that is compatible with the
environment. We suggest you take it in a sealed container to your local service
station for reclamation. Do not throw it in the trash or pour it on the ground.
OIL FILLER CAP
OIL FILLER HOLE
UPPER LEVEL
MAINTENANCE
COVER
MAINTENANCE
COVER SCREW
4. Pull the starter grip until resistance is felt, the pull the starter grip briskly toward the
arrow as shown below.
3. Move the choke handle to the START position.
NOTE:
Do not use the choke when the engine is warm or the air temperature is high.
CAUTION
Do not allow the starter grip to snap back, Return it slowly by hand.
STARTER GRIP
CHOKE HANDLE
START
START

9. MAINTENANCE
The purpose of the maintenance and adjustment schedule is to keep the generator in
the best operating condition.
Inspect or service as scheduled in the table below.
WARNING
Shut off the engine before performing any maintenance. If the engine must be
run, make sure the area is well ventilated. The exhaust contains poisonous
carbon monoxide gas.
CAUTION
Use genuine our parts or their equivalent. The use of replacement parts which
are not of equivalent quality may damage the generator.
NOTE: (1) Service more frequently when used in dusty areas.
(2) These items should be serviced by your servicing dealer, unless you have the proper tools and
are mechanically proficient. Refer to shop manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
ITEM
Perform at every indicated month
or operating hour interval, which-
ever comes first.
REGULAR SERVICE PERIOD(3)
Fuel line Check
Check level
Change
Check
Clean
Check-adjust
Replace
Check-adjust
Clean
Engine oil
Air cleaner
Spark plug
Valve clearance
Fuel tank and filter
EVERY
YEAR
OR
200 HRS
EACH
USE
FIRST
MONTH
OR
20HRS
EVERY 3
MONTHS
OR
50HRS
EVERY 6
MONTHS
OR
100 HRS
(1)
(2)
(2)
Every 2 years (Replace if necessary) (2)
Maintenance Schedule
5.Move the choke handle to the RUN position after the engine warms up.
NOTE
If the engine stops and will not restart, check the engine oil level before
troubelshooting in other areas.
CHOKE HANDLE

WARNING:
The special parallel cable for our IG2000p is only applicable to the parallel operation
of two IG2000p generators. It can not be used for paralleling three or above three
generators.
Be sure only use parallel output cable for parallel running. Other cables are
forbidden.
While connecting the generator and electrical appliance with the parallel output
cable, do carefully and safely insert the plug into the receptacle.
While operating parallel, only output through the receptacle on the parallel cable
wire, don't use the receptacle on the control panel of the generator.
Make sure insert the plugs on the parallel cable wire to the related proper
receptacles.
Make sure the output is directly from the receptacles on the parallel output cable
while parallel running, instead of the receptacles on the generator control panels.
Don't disconnect the PARALLEL I/O special connection cable and parallel output
cable during the parallel running, connect the PARALLEL I/O special connection
cable before start the engine, and then connect the parallel output cable. You can
disconnect the PARALLEL I/O special connection cable and parallel output cable
only after stopping the generator.
If the parallel output cable is still connected, cut off the current output after either
generator was shut off.
Don't use the parallel output cable and parallel connection cable while operating two
generator separately.
Don't connect the parallel cable wire while the two generator running singly.
Read IG2000p operation manual before using the generator.
High altitude operation
At high altitude, the standard carburetor air-fuel mixture will be excessively rich.
Performance will decrease, and fuel consumption will increase.
High altitude performance can be improved by installing a smaller diameter main fuel jet
in the carburetor and readjusting the pilot screws. If you always operate the generator at
altitudes higher than 1,500 m (5,000 feet) above sea level, have your authorized dealer
perform these carburetor modifications.
Even with suitable carburetor jetting, engine horsepower will decrease approximately
3.5% for each 300m (1,000 feet) increase in altitude. The affect of altitude on the
horsepower will be greater than this if no carburetor modification is made.
CAUTION
Operation of the generator at an altitude lower than the carburetor is jetted for
may result in reduced performance, overheating, and serious engine damage
caused by an excessively lean air/fuel mixture.