KitchenAid KSBC1B2 User manual

KSBC1B2

2
PARTS AND FEATURES
1Ingredient cap with measuring cup
2Lid
3Blender jar
4TalonTM blade
5Power cord socket and removable
power cord (not shown)
6Cord cleat (not shown):
To store the cord.
7Base
8On/off switch (not shown)
9Open handle for easy stackability
10 Removable blender jar pad
11 Control dial
12 Pulse toggle switch
13 Start/Stop toggle switch
14 Status indicator light
15 Tamper
16 Front cover with Handle
17 Back cover
18 Thumb Screw
OUNCES
8oz = 1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
1
2
3
4
6
5
8
7
9
11
12
13
14
15
16
17
18 10

3
ENGLISH
COMMERCIAL BLENDER SAFETY
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always
be followed, including the following:
1. Read all instructions.
2. To protect against risk of electrical shock, do not put Blender in water or other
liquid.
3. This appliance is not intended for use by persons (including children) with
reduced physical, sensory, or mental capabilities, or lack of experience and
knowledge, unless they are closely supervised and instructed concerning use
of the appliance by a person responsible for their safety. Close supervision is
necessary when any appliance is used by or near children. Children should be
supervised to ensure that they do not play with the appliance.
4. Turn the appliance OFF, then unplug from the outlet when not in use, before
assembling or disassembling parts and before cleaning. To unplug, grasp the
plug and pull from the outlet. Never pull from the power cord.
5. Avoid contact with moving parts.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or is dropped or damaged in any manner. Contact the
manufacturer at their customer service telephone number for information on
examination, repair or adjustment.
7. Do not use outdoors.
8. Do not let cord hang over edge of table or counter.
9. Keep hands and utensils, other than the tamper provided, out of the container
while blending to reduce the risk of severe injury to persons or damage to the
blender. The cover must remain in place when using the tamper through the
cover opening. A scraper may be used but must be used only when the blender
is not running.
10. Blades are sharp. Handle carefully.
11. Always operate Blender with cover in place.

4
COMMERCIAL BLENDER SAFETY
12. The use of attachments, including canning blender jars, not recommended
by KitchenAid may cause a risk of injury to persons.
13. Do not use appliance for other than intended use.
14. When blending hot liquids or ingredients, Ingredient Cap should remain in place
over the lid opening. Always start on lowest speed and slowly ramp to desired
speed when blending hot liquids or ingredients.
SAVE THESE INSTRUCTIONS
This product is designed for commercial use.
ELECTRICAL REQUIREMENTS
MOTOR HORSEPOWER
Motor horsepower for the blender motor was measured using a dynamometer, a machine
that laboratories routinely use to measure the mechanical power of motors. Our 3.0 peak
horsepower (HP) motor reference reflects the horsepower output of the motor itself and not
the Blender’s horsepower output in the blender jar. As with any blender, the power output in
the jar is not the same as the horsepower of the motor itself.
Voltage: 120 V
Frequency: 60 HZ
Amps: 15.0 A
NOTE: If the plug does not fit in the
outlet, contact a qualified electrician. Do
not modify the plug in any way. Do not
use an adapter.
Do not use an extension cord. If the
power supply cord is too short, have a
qualified electrician or serviceman install
an outlet near the appliance.

5
ENGLISH
GETTING STARTED
The Blender has a preset recipe program: Icy Drinks, Variable speeds, and Pulse functions.
BLENDER FUNCTION GUIDE
Setting Description Blending
Time
(in min:sec)
Suggested Items to
Blend
Icy
Drinks
Incorporates icy drink ingredients at
low speed, then ramps up to high
speed for a complete blend. 0:22
Ice, whole fruits or
vegetables, or frozen
fruits. Drinks such as
Margaritas, Daiquiris, and
blended ice coffee drinks.
Low The Blender will run on low speed
until the Start/stop is pressed, or
will stop after 6 minutes. N/A
Med The Blender will run on medium
speed until the Start/stop is
pressed, or will stop after 6 minutes. N/A
High The Blender will run on high speed
until the Start/stop is pressed, or
will stop after 6 minutes. N/A
Pulse
H/L Use Pulse during manual operation
to add a boost of power. N/A
Variable
Times
Starts at a slow speed and ramps
up to a high speed for optimal
blending results. 0:05-0:60
PRODUCT ASSEMBLY
Install the back cover by aligning the tab
on the rear side of the base with the slot
on the back cover.
1
Secure both sides over the tabs on the
either side of the blender base.
2
First, clean all parts and accessories (see “Care and Cleaning” section). Place the blender in a
dry and clean area.

6
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or
electrical shock.
Make sure the power switch is OFF.
Securely attach the removable power cord
into the back of blender. Plug the Blender
into a grounded 3 prong outlet.
5
Flip the power switch to ON (I).
The status indicator light will flash,
indicating that the Blender is in Standby
mode and ready to operate.
6
Install and secure the thumb screws on
both sides by hand.
3
Secure the front cover to the back cover.
4
GETTING STARTED

7
ENGLISH
USING THE COMMERCIAL BLENDER
IMPORTANT : When moving your Blender, always close the Front cover and support/lift
from the Blender base. Base will become disengaged from jar if carried by Blender jar
or Blender jar handle only. Do not lift by the cover or cover handle.
O U N C E S
8oz= 1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
OUNCES
8oz= 1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
Add items (max. 60oz). Add liquids first,
then soft foods, then leafy greens, and ice
or frozen items last. Secure the lid.
1
OU N C E S
8oz=1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
OU N C E S
8oz=1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
Open the front cover. Place the blender
jar on the base, aligning with the jar pad.
Close the Front cover.
2
OUNCES
8oz= 1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
OUNCES
8oz= 1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
Turn the control dial to your desired speed,
time, or program.
Flip the START/STOP toggle switch up or
down to start. See the “Blender function
guide” for more details.
3
1
2
OU N C E S
8oz=1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
OU N C E S
8oz=1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
Using the Tamper (optional): Open front
cover. Remove the Ingredient cap only. Stir
or press contents down towards the blade.
When finished, replace the Ingredient cap
before resuming blending.
4
12
8
16
20
24
4
Using the Pulse mode (optional): Press
and hold the PULSE toggle switch up for a
faster pulse, or down for a slower pulse.
NOTE: The Pulse function may also be
used on its own as a separate blending
function while the Blender is in Standby
mode.
5
12
8
16
20
24
4
When finished, flip the START/STOP toggle
switch up or down to stop.
Allow the Blender to completely stop
before removing the lid or pouring out the
blended ingredients.
NOTE: Icy Drink cycle and variable timer
cycles will stop automatically at the
completion of the cycle.
6

8
CARE AND CLEANING
SANITIZING THE BLENDER JAR
1. Remove all contents from the blender jar.
2. Fill ¾ of the jar with a sanitizing solution mix of 1.5 tsp. (7.4 mL) institutional or
household bleach in 60 oz (1.75 L) water. Place the lid, and securely place the blender
jar onto the blender base.
3. Run the blender on the High Speed setting for 35 seconds.
4. Turn off to let the sanitizing mix sit in the blender jar for an additional 2 minutes.
5. Pour out the solution. Do not rinse the blender jar.
6. Place the lid on the blender jar. Make sure the empty blender jar is fully in place on
the blender base. Run the empty Blender for an additional 10 seconds. Do not rinse
the jar after sanitizing.
7. Allow the blender jar to air dry.
Fill half of the jar with warm water and add
1 or 2 drops of dish-washing liquid. Secure
the Lid and Ingredient Cap. Place the jar
on the base. Close the front cover.
1
O U N C E S
8oz= 1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
O U N C E S
8oz= 1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
Rotate the control dial to 50 seconds.
Flip the START/STOP toggle switch up or
down. When the timer finishes, remove
and empty contents and rinse with warm
water and dry thoroughly.
2
NOTE: Do not immerse the Blender base or cord in water. Do not use abrasive
cleansers or scouring pads to avoid scratching.
OUNCES
8oz= 1Cup
60
56
52
48
44
40
36
32
28
12
8
16
20
24
4
Unplug before cleaning. Wipe the base
and the cord with a warm, damp cloth and
dry with a soft cloth.
3
OU N C E S
8oz=1Cup
60
56
52
48
44
40
36
32
28
14
8
16
20
24
4
Wash the blender jar, jar pad, lid, front
cover, back cover, handle, and ingredient
cap by hand with a damp cloth and warm
soapy water; rinse with warm water, and
dry with a soft cloth.
4
NOTE: Handle must be removed from the front cover prior to cleaning by removing the
two screws inside the front cover.

9
ENGLISH
TROUBLESHOOTING GUIDE
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or
electrical shock.
Problem Solution
Status indicator light is off while
unit is plugged in and On/Off
switch is in On position:
After 10 minutes of no activity, the blender will go into
Sleep mode. Flip START/STOP toggle switch up or down
to bring the blender back into Standby mode.
Status indicator light is flashing
orange color:
Indicates error mode. This can be caused by: using
a spatula or any other utensil that could obstruct the
blade to freely spin, or having an ice cube or hard food
in a location that locks up the blade.
Unplug the blender and remove the jar from the base,
and clear the items. Place the jar back on the base, and
then turn on the blender to continue regular use.
Blender stops after continuously
running for 6 minutes: This is normal operation for variable speed functions.
Refer to “Blender function guide” for details.
Blender stops while blending: If blender stops prior to the completion of the selected function, contact an authorized service center for
assistance.
If the ingredients of a recipe
aren’t blending:
An air pocket can be created around the blade causing
the ingredients to miss the blade. Use the tamper to
push ingredients down into the blade. Refer to “Using
the commercial blender” section. For certain recipes,
adding more liquid may also assist in incorporating the
ingredients.
Blender jar overflows:
Unplug and remove the jar pad from the housing to
make sure the base is fully dry. The control dial can be
detached by pulling it off with force. Wipe dry, and then
replace it back.
Troubleshooting does not solve
the problem:
See the “Warranty and service” section. Contact an
Authorized Service Center for assistance.
Do not return the Blender to the retailer – retailers do
not provide service.

10
WARRANTY AND SERVICE
KITCHENAID®COMMERCIAL BLENDER WARRANTY FOR THE 50
UNITED STATES, THE DISTRICT OF COLUMBIA, AND CANADA
This warranty extends to the purchaser and any succeeding owner for Commercial Blenders
operated in the 50 United States, the District of Columbia, and Canada.
Length of Warranty: Two Year Full Warranty for Blender Base, Front cover,
and Back cover and One Year Full Warranty for Blender
Jar from date of purchase.
KitchenAid Will Pay
for Your Choice of: Hassle-Free Replacement of your Commercial Blender. See the next page for details on how to
arrange for service, or call the Customer eXperience
Center toll-free at 1-855-845-9684.
OR
The replacement parts and repair labor costs to correct
defects in materials and workmanship. Service must be
provided by an Authorized KitchenAid Service Center.
See the KitchenAid®Commercial Blender Warranty for
Puerto Rico for details on how to arrange for service.
KitchenAid Will
Not Pay for: A. Damage resulting from accident, alteration, misuse or abuse.
B. Replacement parts or repair labor costs for
Blender operated outside the 50 United States
and District of Columbia.
C. Replacement of the jar or base unit due to
cosmetic issues.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED
TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY
BE IMPOSED BY LAW ARE LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD
ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS
OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY
TO YOU.
IF THIS PRODUCT FAILS TO WORK AS WARRANTED, CUSTOMER’S SOLE AND
EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT ACCORDING TO THE
TERMS OF THIS LIMITED WARRANTY. KITCHENAID AND KITCHENAID CANADA
DO NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state or province to province.