Klipspringer LAZATHERM 300 User manual

ATLC300
LAZATHERM 300
Product Code: ATLC300
t/ [phone]
e/
[e-mail]
www.klipspringer.com
Klipspringer Ltd
Rynor House, Farthing Road,
IPSWICH, UK, IP1 5AP

2
TABLE OF CONTENTS
1. INTRODUCTION .................................................................................... 3
2. CAUTION ............................................................................................... 3
3. OPERATION ............................................................................................ 3
4. TEMPERATURE MEASUREMENT ............................................................. 4
5. MALFUNCTION INDICATORS ................................................................. 4
6. BATTERY ................................................................................................ 4
7. TECHNICAL DATA .................................................................................. 5
8. FUNCTION MENU ................................................................................... 5
9. SERVICE ................................................................................................. 5
10. CLEANING .............................................................................................. 5
11. CALIBRATION ........................................................................................ 6
12. ASSURANCE ............................................................................................ 6

3
1.0 INTRODUCTION
1.1 Congratulations on your purchase of your ATLC300 thermometer from
Klipspringer. With considerate operation it should provide accurate and
stable measurements for a long time to come.
1.2 All temperature readings, fault detections, functions etc will display
clearly on the LCD screen.
1.3 A replaceable lithium battery provides approximately five years of
reliable operation.
2.0 CAUTION
The thermometer must be protected from:
2.1 Electrostatic discharge
2.2 Thermal shock caused through sudden extreme ambient temperature
changes. Allow instrument to stabalise for up to 30 seconds when
affected or when moving into extreme changes in ambient
temperatures.
2.3 Contact or close proximity to high heat sources.
3.0 OPERATION
3.1 The default unit of measurement is degrees Celcius (ºC). [Can be
changed to Farenheit – please contact the Klipspringer support team.]
3.2 To switch ON swing the foldable probe out greater than 20ºC.
3.3 Power off, the thermocouple probe swings back to switch off.
4.4
Magnetic, attach to metal surface for easy storage.

4
4.0 TEMPERATURE MEASUREMENT
4.1 Ensure that the thermometer probe is inserted to a preferred depth of
25mm into the medium and that contact is maintained until readings
become stable.
5.0 MALFUNCTION INDICATORS
5.1 ‘HI’ display: temperature measured is above range.
5.2 ‘Lo’ display: temperature measured is below range.
5.3 ‘Er2’ display: The thermometer is exposed to rapid
changes in the ambient temperature.
5.4 ‘Er3’ display: when the ambient temperature exceeds
0 ºC (32ºF) or + 50ºC (122ºF). The thermometer
should be allowed plenty of time (minimum 30 minutes)
to stabalise to the working temperature.
5.5 ‘Er’ for all other error messages it is necessary to reset
the thermometer. To reset, turn the instrument off,
remove the battery and wait for a minimum of one minute,
reinsert the battery and turn on.
5.6Contact our technical helpline if diagnosis is not clear.
6.0 BATTERIES
6.1 The lithium battery has an expected lifespan of up to five years
allowing for two hours continuous use each day.
6.2 The battery symbols indicate power status.
Battery
operational
Battery
operational
Battery needs
to be replaced
6.3 For best results, return instrument to Klipspringer Service Centre for
battery replacement and service check. NB Battery is welded into
thermometer circuitry and is not suitable for ‘diy’ replacement.

5
7.0 TECHNICAL DATA
Measuring range
-50...+350°C
Accuracy
±0.5°C
Resolution
0.1°C
Operating range
0...+50°C
Battery
Lithium type CR2032
Battery life
100 hours of continuous use
Sensor type
Pt1000
Auto power-off
Swing back probe for power off
Dimensions
150x54x18mm
Weight
Approx. 76grams
8.0 FUNCTION MENU
8.1 To change any of the below please contact our technical team on +44
(0)1473 461 800 or [e-mail].
ºC / ºF
9.0 SERVICE
9.1 For service and repairs please send the unit to the address below in the
box provided for your use. DO NOT attempt to open the case. The
instrument contains delicate electronic components and opening the
case may invalidate your warranty.
10.0 CLEANING
10.1 Cleaning is best performed by wiping with a soft cloth and mild soap
solution. Do not use solvents.

6
11.0 CALIBRATION
11.1 In order to guarantee optimum precision, we recommend that this
instrument should be calibrated each year.
11.2 Klipspringer will automatically notify you of the due date for calibration.
11.3 The thermometer will be returned within one week accompanied by a
certificate of calibration.
11.4 Klipspringer is a UKAS accredited laboratory for temperature calibration
(0764) in accordance with BS EN ISO/IEC 17025. This service is
provided to cover almost any probe hand-held thermometer currently in
use.
12.0 ASSURANCE
12.1 With considerate use and Klipspringer’s support, this unit will give years
of accurate service.
© Copyright 2022. Klipspringer Ltd.