Klutch 24V Cordless 1/2in. Impact Wrench User manual

0110
24V Cordless
1/2in. Impact Wrench

Thank you very much for choosing a Klutch product!
For future reference, please complete the owner's record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is important that you read the entire
manual to become familiar with this product before you begin using it.
This machine is designed for certain applications only. The distributor cannot be responsible
for issues arising from We strongly recommend this machine is not
and/or used for any application other than that for which it was designed. If you
have any questions relative to a particular application, DO NOT use the machine until you
have contacted the distributor to determine if it can or should be performed on
the product.
For technical questions please call 1-800-222-5381.
1
TM

GENERAL SAFETY RULES

17. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces: pipes, radiators, ranges, and refrigerator enclosures. When drilling
or cutting into walls, floors, or wherever “live” electrical wires may be encoun-
tered, try to ascertain whether there is a danger of shock. Even so, DO NOT
TOUCH METAL PARTS OF THE TOOL. Hold the tool only by the plastic
handle or the side grip to prevent electric shock if you hit a live wire.
18. REPLACEMENT PARTS. When servicing, use only identical replacement
parts.
PRECAUTIONS FOR BATTERY AND CHARGER
1. CHARGE BATTERIES FULLY before initial use.CHARGE BATTERIES FULLYCHARGE BATTERIES FULLY
2. CHARGE AT ROOM TEMPERATURE. Temperature must be higher than
32°F (0°C) and lower than 122°F (50°C).
3. DO NOT CHARGE IF CHARGER’S CORD OR PLUG IS DAMAGED. Charg-
Charg-
ing with damaged cord may result in fire or electrical shock. If charger is
damaged in any way, have it repaired by a qualified serviceman.
4. DO NOT SHORT ACROSS TERMINALS OF BATTERY. Take care that
metal such as paper clips, nails, the sides of a metal toolbox do not cause a
short in your battery. Extremely high temperatures and fire can result.
5. DO NOT INCINERATE BATTERY
Voltage: 24V
No Load Speed: 0 - 2300 RPM
Kit Includes: 24V Cordless Impact Wrench, 2 - 24V Battery Packs,1 Charger,
11/16in. Socket, 3/4in. Socket, 13/16in. Socket, 15/16in. Socket and Blow-Molded Case
WARNING:
For your own safety do not attempt to use your electrical tool until
the battery is fully charged and you have read all the instructions.
REMEMBER:
This cordless tool is always in an operating condition and does
not need to be connected to a power supply.
CAU
TION:
•
Do Not expose either the electical tool or charger to rain or water.
•
Do not overcharge the battery as this could damage the battery cells.
•
Do not force the tool. If the tool is laboring, it is possible that the battery
power is low. If so, stop working and recharge the battery pack.
•
To prolong the life of the tool, do not continually work more than 20 minutes
at a time.
SPECIFIC SAFETY RULES
SPECIFICATIONS
!
!
!
!
Power Pack Capacity: 1.3Ah (Ni-Cd)
3
OPERATING PROCEDURES
GENERAL SAFETY RULES

GETTING TO KNOW YOUR CORDLESS TOOL/CHARGER
24V CORDLESS 1/2in. IMPACT WRENCH:
1. 1/2in. Square Socket Drive
2. Metal Gear Housing
3. Ventilation Slots
4.
Forward / Reverse / Neutral Lock Switch
5.
Variable Speed Trigger Switch
6. Padded Hand Grip
7. Battery Release Button
8. B
attery Pack
GENERAL
•
This tool is intended for use with 1/2in. drive impact sockets for loosening ond
tightening nuts and bolts. Its impacts help to turn stiff fasteners.
•
To prolong the life of the tool, do not use it continuously for more than 20
minutes at a time.
•
If the tool shows signs of diminishing power, stop and recharge the battery.
Using it to do heavy work when the battery is weak drains the battery very
quickly and can damage the battery.
•
To use the tool, first start the fastener on the thread by hand, being sure it is
not cross-threaded.
•
Choose a 1/2in. drive socket of the correct size and mount it on the drive shaft.
•
Place the socket over the fastener.
•
Use the variable speed only for starting.
•
Allow the tool to come up to full speed.
•
When you hear the sound of the impacts, stop after three or four. The fas-
tener is tight.
VARIABLE SPEED
You can vary the spindle rotation speed by modulating finger pressure on the trigger.
OPERATING PROCEDURES
1
4
2
3
5
6
7
8

ROTATION DIRECTION
Your tool is equipped with a 3-position Forward / Reverse / Neutral Lock Switch
through the housing above the trigger. When knob is pushed toward the right,
rotation is forward (clockwise). When pushed in from the right to the left side,
rotation is reversed (counter-clockwise), and when in center position, it is locked
in neutral and the trigger is blocked. Do not push the rotation direction knob until
the drive stops turning.
BATTERY PACK
1.
Battery must be charged before using tool for the first time. Batteries will
reach full performance after about five charge/discharge cycles.
2.
Always have 3-position Forward / Reverse / Neutral Lock Switch in the center
position when removing or inserting battery to avoid unintentional starting.
3.
Remove the battery from the tool. Press the Battery Release Button and
remove battery.
4
. Place battery on the charger.
5.
To charge, plug the charger’s AC input plug into a 110/120V household current.
6.
light comes on.
7.
IMPORTANT: Ensure that charging takes place in a safe, secure location away
from liquids.
8.
Normal charging time is approximately 1 hour.
9.
lock spring clicks.
10.
11.
recharging before you use the tool.
12.
charge. They should then be replaced. Dispose of batteries at an appropriate waste
trash receptacles.
•
Keep the tool clean using a soft damp (not wet) cloth. Do not use solvents
on the plastic parts.
•
Lubrication is not necessary. After long use, have an authorized service
center maintain and lubricate the tool.
OPERATING PROCEDURES
MAINTENANCE
5
When charging more than one pack in succession, allow 15 minutes between charges.
To insert the battery into the tool, simply slide the pack in until Battery Release Button
The battery discharges slowly over time, even when not used, and may require
After many charge/discharge cycles, your batteries will lose their ability to hold a
disposal facility. They contain cadmium, so do not throw batteries away in common
When battery is charging, red light is on. When battery is finished charging, a green

PART No. DESCRIPTION
01 Gear Cover
02 Hermetic Ring
03 Drive Shaft Sheath
04 Shaft Washer
05 Square Drive Shaft
06 Housing (right)
07 Clutch
08 Washer
09 Spring
10 Planetary Gear
11 Core Shaft
PART No. DESCRIPTION
12 Column Pin
13 Shaft Bushing
14 Inside Gear
15 Gear Box
16 Connection Clip
17 D.C. Motor
18 Forward/Reverse/Neutral Lock Button
19 Battery Pack
20 Trigger Switch
21 Housing (left)
PARTS LIST
6