KNOVA KN M-2502N User manual
KN M-2502N
Metal and wood slide
compound miter saw
10
”
Sierra angular compuesta deslizable para metal y madera
(254 mm)
DANGER
PRODUCT SPECIFICATIONS
MOTOR
Power Source:
120V AC, 60Hz, 15 Amp
Arbor Shaft Size:
5/8 in.
Speed (no load):
2400 RPM (No load)
Electric Brake: Yes
Double Insulated:
Yes
TABLE OF CONTENTS
1
WARNINGS
Your risk
WARNING
SYMBOLS
WARNING ICONS
-
PROHIBITION
BLADE
Diameter: 10 in.
Arbor: 5/8 in.
Dust port. (o.d.):
1-1/4 in.
Net weight: 23.18 kg
MITER SAW
Rotating Table:
Miter Detent Stops:
0, 15, 22.5, 31.6, 45º R & L
Bevel Positive Stops:
0, 33.9, 45º R & L
WARNING
WARNING
CAUTION
CAUTION
CUTTING CAPACITY
Crosscut: 3-3/8 in. x 11-23/32 in.
Miter 45° R & L: 3-3/8 in. × 7-25/32 in.
Bevel 45º R & L: 1-5/8 in. x 11-23/32 in.
Compound 45°: 1-5/8 in. x 7-25/32 in.
Steel Plate: 7/32 in. thickness
Square Steel Box:
2 in. (1/8 in. thickness)
Round Steel Tube:
2 in. (1/8 in. thickness)
WARNING
2
POWER TOOL SAFETY
WARNING
3
SLIDE COMPOUND MITER SAW SAFETY
NOT
ARE
THIS SAW IS RECOMMENDED
Never
ELECTRICAL REQUIREMENTS AND SAFETY
POWER
WARNING
-
The power-
Replacement parts
Polarized plugs
WARNING
To avoid electrocution:
4
ELECTRICAL REQUIREMENTS AND SAFETY
PRE-ASSEMBLY
ACCESSORIES AND ATTACHMENTS
RECOMMENDED ACCESSORIES
MINIMUM GAUGE FOR EXTENSION CORDS (AWG)
(When using 120 volts only)
Ampere Rating Total length of Cord
More than
Not more than
25ft. 50ft. 100ft. 150ft.
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12
Not Recommended
WARNING
ACCESSORIES
WARNING
SUPPLIED NOT SUPPLIED
MOTOR SAFETY PROTECTION IMPORTANT
-
Use a proper extension cord.
-
Be sure your extension cord is properly-
Use a separate electrical circuit for your tools. This circuit
-
5
CARTON CONTENTS
WARNING
WARNING
miter
Dust Collector
KNOW YOUR SLIDE COMPOUND MITER SAW
6
Dust Collector
Holes
Switch
Switch
Motor
Dust Port
7
GLOSSARY OF TERMS
ARBOR
BASE
CARBIDE
EYE
-
FACE
FENCE
MITER
MITER
SWITCH
WARNING
WOODWORKING TERMS
ARBOR
CROSS
FREEHAND
KERF
KICKBACK
MITER
SAW
SET
THIN-KERF
WORKPIECE
8
ASSEMBLY
The
WARNING
-
WARNING
Raising the cutting head:
Locking the cutting head:
9
ASSEMBLY
WARNING
NOTE-
-
WARNING
Removing Blade (Fig. H, I, J, K)
the
to the up
ASSEMBLY
10
Installing Blade (Fig. H, I, J, K)
WARNING
WARNING
To avoid injury from unexpected saw
movement:
Mounting instructions:
9
ADJUSTMENTS
11
WARNING
WARNING
90¡ (0¡ ) bevel stop adjustment (FIG. O)
90¡ bevel pointer adjustment (FIG. P)
45¡ bevel adjustment (FIG. Q)
33.9¡ bevel adjustment (FIG. Q)
The
lock the miter
ADJUSTMENTS
12
WARNING
The depth
The
-
ADJUSTMENTS
13
The
WARNING
rocker switch
rocker
NOT
A. Checking Laser Beam Alignment (Fig. Y)
B. Adjusting the translation position of the Laser Beam
(Fig. Y, Z)
WARNING
WARNING
C. Aligning the Laser Beam (Fig. Y, Z, AA, BB)
the two screws
clockwise
Side
Side
OPERATION
14
Cluttered
WARNING
• Use the right tool. DonÕ t force a tool or attachment to
do a job it was not designed to do. Use a different tool
for any workpiece that canÕ t be held in a solidly braced,
xed position.
CAUTION
DRESS FOR SAFETY
power
BEFORE
WARNING
Disconnect the miter saw.
• Compare the direction of rotation arrow
• Tighten the arbor bolt.
• Tighten the cover plate screw.
• Check for damaged parts.
Check
electric cords
holes
15
OPERATION
WARNING
WARNING
-
Starting a cut:
Finishing a cut:
Before freeing jammed
material:
BASIC SAW OPERATIONS
WARNING
-
The
-
DO
Keep
Never cut freehand:
WORKPIECES
16
OPERATION
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
17
OPERATION
To avoid injury:
To Slide Cut Wide Boards (Fig. KK)
the
Cut these
out the middle
WARNING
WARNING
OPERATION
18
Holes
Check
-
F
e
c
e
Workpiece
F
e
c
e
Workpiece
Your-
when added together, equal exactly 90¡ .
Most
90¡ inside or
outside corner,
A bowed workpiece must be
workpiece
try to cut the
workpiece
without the
stop
19
OPERATION
F
e
c
e
Workpiece
F
e
c
e
Workpiece
KEY
MITER SETTING
Inside corner - Left side
IR
Inside corner - Right side
Outside corner - Left side
OR
Outside corner - Right side
CROWN MOLDING CHART
Compound Miter saw
Miter and bevel Angle settings
Wall to Crown Molding Angle
Miter
Miter
Miter
Miter
Bevel/Miter Settings
Table of contents
Languages:
Other KNOVA Saw manuals
KNOVA
KNOVA KN SCM-09 User manual
KNOVA
KNOVA KN SS-18VVS User manual
KNOVA
KNOVA KN BTS-10W User manual
KNOVA
KNOVA KN M-2504RC User manual
KNOVA
KNOVA KN M-2500N User manual
KNOVA
KNOVA KN SCM-05P User manual
KNOVA
KNOVA KN M-2500W User manual
KNOVA
KNOVA KN M-2509RC User manual
KNOVA
KNOVA KN M-3057R User manual
KNOVA
KNOVA KN SS-16LV User manual
Popular Saw manuals by other brands
Bridge City
Bridge City Signature Series manual
Jet
Jet HVS-8-DMW Operating instructions and parts manual
Kity
Kity KS216S Translation from the original instruction manual
Craftsman
Craftsman 103.24280 Operating and parts manual
Metabo HPT
Metabo HPT C 12RSH3 Safety instructions and instruction manual
Ryobi
Ryobi R18JS7 Original instructions
