Koden MDC-5004 Installation manual

MDC-5000 Series Revision History
0093153004-00 i
MDC-5000 Series Operation Manual
Doc No: 0093153004
Document Revision History
No.
Doc. No.- Rev. No.
Date Revised
(Y/M/D)
Revised Content
0
0093153004-00
2017/12/22
First edition
1
2
3
4
5
6
7
8
9
10
Document No. Revised Version Norm
When part of the document needs to be revised, the document has advanced revision number.
The document No. is indicated at the lower right side on the cover and at the left or right side of the
footer region of each page.
© 2017 Koden Electronics Co., Ltd. All rights reserved.
No part of this publication may be reproduced, transmitted, translated in any from by any means without
the written permission of Koden Electronics Co., Ltd. The technical descriptions contained in this
publication are subject to change without notice. Koden assumes no responsibility for any errors,
incidentals or consequential damages caused by misinterpretation of the descriptions contained in this
publication.

Important Notice MDC-5000 Series
ii 0093153004-00
Important Notice
For copy and transcription of this Operation Manual (hereinafter referred to as this manual),
permission from Koden is needed. Koden prohibits the un-authorized copy and transcription of this
manual.
If this manual is lost or damaged, consult a dealer of Koden or Koden.
The specification of the products and the contents in this manual are subject to change without
notice.
The contents displayed on the menu of product may be different from the expression of this
manual. The fonts and shapes of the keys and menus in the illustration may differ from the actual
ones, and some parts may be omitted.
Koden is not liable for damages and troubles arisen from misunderstanding of the contents in this
manual.
Koden is not liable for any damages caused by earthquake, lightning, wind and flood damage and
fire for which Koden is not responsible, and actions by third parties, other accidents, customer’s
unintended error/abuse and the use under other abnormal conditions.
Koden is not liable for damages of accompaniment (change/loss of memorized content, loss of
business profit, stop of business) arisen from use or failure of our products.
If the stored data are changed or lost, irrespective of causes of troubles and damages, Koden is
not liable for them.
Koden is not liable for any damages arisen from malfunction caused by combination of software
and connected equipment in which Koden is not engaged.

MDC-5000 Series For Your Safe Operation
0093153004-00 iii
For Your Safe Operation
Symbols used in this Operation Manual
This manual uses the following symbols. Understand the meaning of each symbol and implement the
maintenance and inspection.
Symbol
Meaning
Warning Symbol
This symbol denotes that there is a risk of death or serious injury when not
dealt with it correctly.
High Voltage Danger Symbol
This symbol denotes that there is a risk of death or serious injury caused by
electric shock when not dealt with it correctly.
Caution Symbol
This symbol denotes that there is a risk of slight injury or damage of device
when not dealt with it correctly.
Prohibition Symbol
This symbol denotes restriction of the specified conduct. Description of the
restriction is displayed near the mark.
IMPORTANT
Important Symbol
This mark indicates important area where attention is needed. This may
include possible data lose or other issues that may interfere with radar
operation.
Reference Symbol
This mark shows the part to be referred to concerning this description.

For Your Safe Operation MDC-5000 Series
iv 0093153004-00
Caution related to Equipment
Caution, high voltage inside.
High voltage that may cause severe injury or death is present. High
voltage remains in circuit even after power is turned off. High voltage
circuit has a protective cover with a warning label. Make sure to turn off
power and discharge capacitors before working on the system. Only
authorized personnel should access this circuit for repair and
maintenance.
Confirm main power is turned off before servicing the
equipment.
If power switch is turned on while working on the system, possible
severe injury or death may occur due to high voltage. Make sure main
power is off and a label “Work In Progress”is attached to the breaker
powering the system.
Caution related to dust
Inhaling dust may cause Arespiratory disease. When cleaning the inside
of equipment, be careful not to inhale dust. Wearing a safety mask is
recommended.
When choosing equipment location
Do not install the equipment where it is excessively damp, humid and
under direct dripping water.
Caution related to static electricity
Static electricity may be generated from floor carpet or synthetic clothes.
Static may destroy some electronics parts of the circuit and therefore
anti-static measures should be done.
Prohibited matter
Any Display and Scanner unit combination other than specified in the
manual is prohibited and will void manufacturer’s warranty.

MDC-5000 Series For Your Safe Operation
0093153004-00 v
Caution rellated to Handling
ENGLISH:
Caution related to rotating aerial
The radar antenna may start rotating to rotate without notice. Please stand
clear from the antenna for your safety.
Caution related to electromagnetic disturbance
The operating Antenna & Scanner unit radiates high-energy
electromagnetic wave. It may cause harmful effect for human body due to
its continuous radiation. As International regulation says, electromagnetic
waves less than 100 watt/m2does not have a harmful effect on human
bodies, but some kind of medical devices such as heart pacemakers are
sensitive even under the low energy electromagnetic wave. Any personnel
with such a device should keep away from the electromagnetic wave
generating position at all times.
Specified power density and distance from the radar (in accordance with the
provision as specified in IEC 60945)
Model name
Transmission power /
Antenna length
100W/m2
50W/m2
10W/m2
MDC-5004
4kW / 3 feet Antenna
0.9 m
1.3 m
2.8 m
4kW / 4 feet Antenna
1.0 m
1.4 m
3.1 m
4kW / 6 feet Antenna
1.2 m
1.7 m
3.7 m
MDC-5006
6kW / 4 feet Antenna
1.5 m
2.1 m
4.5 m
6kW / 6 feet Antenna
1.7 m
2.4 m
5.4 m
MDC-5012
12kW / 4 feet Antenna
2.1 m
2.9 m
6.4 m
12kW / 6 feet Antenna
2.4 m
3.4 m
7.6 m
12kW / 9 feet Antenna
2.9 m
4.1 m
9.0 m
MDC-5025
25kW / 4 feet Antenna
2.9 m
4.1 m
9.2 m
25kW / 6 feet Antenna
3.5 m
4.9 m
10.9 m
25kW / 9 feet Antenna
4.1 m
5.8 m
13.0 m

For Your Safe Operation MDC-5000 Series
vi 0093153004-00
FRENCH:
Mise en garde relative aux perturbations électromagnétiques produites
par les radars de navire
L'antenne & l’émetteur des radars de navire ont un rayonnement d’ondes
électromagnétique de haute intensité. Ceci peut causer des effets nocifs pour le
corps humain en raison de son rayonnement continu. Comme la réglementation
internationale le spécifie, les ondes électromagnétiques à moins de 100 watt/m2
n'ont pas un effet néfaste sur le corps humain, mais certains types d’appareils
médicaux tels que les stimulateurs cardiaques peuvent être affectes même par des
ondes électromagnétiques de faible énergie. Tout membre du personnel avec un tel
dispositif devrait se tenir à l'écart des générateurs d'ondes électromagnétiques en
tout temps.
Spécification de densité de la puissance et de la distance du radar (conformément à
la disposition comme spécifié dans la IEC 60945)
Nom Modèle
Puissance de transmission
/ longueur d’antenne
100W/m2
50W/m2
10W/m2
MDC-5004
4kW / Antenne 3 pieds
0.9 m
1.3 m
2.8 m
4kW / Antenne 4 pieds
1.0 m
1.4 m
3.1 m
4kW / Antenne 6 pieds
1.2 m
1.7 m
3.7 m
MDC-5006
6kW / Antenne 4 pieds
1.5 m
2.1 m
4.5 m
6kW / Antenne 6 pieds
1.7 m
2.4 m
5.4 m
MDC-5012
12kW / Antenne 4 pieds
2.1 m
2.9 m
6.4 m
12kW / Antenne 6 pieds
2.4 m
3.4 m
7.6 m
12kW / Antenne 9 pieds
2.9 m
4.1 m
9.0 m
MDC-5025
25kW / Antenne 4 pieds
2.9 m
4.1 m
9.2 m
25kW / Antenne 6 pieds
3.5 m
4.9 m
10.9 m
25kW / Antenne 9 pieds
4.1 m
5.8 m
13.0 m

MDC-5000 Series For Your Safe Operation
0093153004-00 vii
Warning Statements related to FCC and IC rules
IC RSS-GEN, Sec 8.3 Warning Statement- (Required for Transmitters
w/ detachable antennas)
ENGLISH:
This radio transmitter (identify the device by certification number, or model number if
Category II) has been approved by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and required antenna impedance for
each antenna type indicated.Antenna types not included in this list, having a gain greater
than the maximum gain indicated for that type, are strictly prohibited for use with this
device.
FRENCH:
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son
numéro de modèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie
Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal et l'impédance requise pour chaque type d'antenne. Les types
d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal
indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Antenna type name
Antenna Gain (dBi)
Required Impedance (ohm)
RW701A-03
25.3dBi
50ohm
RW701A-04
27.0dBi
50ohm
RW701A-06
28.5dBi
50ohm
RW701B-09
30.0dBi
50ohm

For Your Safe Operation MDC-5000 Series
viii 0093153004-00
IC RSS-102, Sec 2.6 Warning Statement Requirements
ENGLISH:
The applicant is responsible for providing proper instructions to the user of the radio
device, and any usage restrictions, including limits of exposure durations. The user
manual shall provide installation and operation instructions, as well as any special usage
conditions, to ensure compliance with SAR and/or RF field strength limits. For instance,
compliance distance shall be clearly stated in the user manual.
FRENCH:
Le demandeur est responsable de fournir des instructions appropriées et toute restriction
d'utilisation, y compris les limites des durées d'exposition, à l'utilisateur de l'appareil radio.
Le manuel de l'utilisateur doit fournir des instructions d'installation et d'utilisation, ainsi
que toutes les conditions d'utilisation spéciales, pour assurer la conformité aux limites
SAR et / ou RF. Par exemple, la distance de conformité doit être clairement indiquée
dans le manuel de l'utilisateur.
IC RSS-GEN, Sec 8.4 Warning Statement- (Required for
license-exempt devices)
ENGLISH:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
FRENCH:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.

MDC-5000 Series For Your Safe Operation
0093153004-00 ix
Warning statement regarding RF exposure compliance
ENGLISH:
The user manual of devices intended for controlled use shall also include information
relating to the operating characteristics of the device; the operating instructions to ensure
compliance with SAR and/or RF field strength limits; information on the installation and
operation of accessories to ensure compliance with SAR and/or RF field strength limits;
and contact information where the user can obtain Canadian information on RF exposure
and compliance. Other related information may also be included.
FRENCH:
Le manuel de l'utilisateur des dispositifs destinés à une utilisation contrôlée doit
également comporter des informations relatives aux caractéristiques de fonctionnement
du dispositif; Le mode d'emploi pour assurer la conformité aux limites SAR et / ou RF; Des
informations sur l'installation et le fonctionnement des accessoires afin d'assurer la
conformité aux limites SAR et / ou RF; Et des coordonnées où l'utilisateur peut obtenir des
renseignements canadiens sur l'exposition aux radiofréquences et la conformité. D'autres
renseignements connexes peuvent également être inclus.
FCC Part 15.19 Warning Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
FCC Part 15.21 Warning Statement
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR
MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR
COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
FCC Part 15.105(b) Warning Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a

For Your Safe Operation MDC-5000 Series
x 0093153004-00
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.

MDC-5000 Series For Your Safe Operation
0093153004-00 xi
Do not disassemble or modify. It may lead to trouble, fire, smoking or
electric shock. In case of trouble, contact our dealer or our company.
In case of smoke or fire, switch off the power in the boat and the power of
equipment. It may cause fire, electric shock or damage.
Caution related to remaining high voltage.
A high voltage may remain in the capacitor for several minutes after
system is powered off. Before inspecting inside, wait at least 5 minutes
after powering off or discharging the remaining electricity in an appropriate
manner. Then, start the work.
The information displayed in this unit is not provided directly for your
navigation. For your navigation, be sure to see the specified material.
Use properly rated fuse. If incorrect fuse is used, it may cause fire, smoke
or damage.

Break in procedure of stored radar MDC-5000 Series
xii 0093153004-00
Break in procedure of stored radar
Following procedure is recommended for “Break In” of the stored radar.
Otherwise the radar sometimes exhibits unstable transmitting operation
such as arcing at its initial operation after long period of storage and make
the operation more difficult.
1. Extend preheat time as long as possible (preferably 20 to 30
minutes).
2. Set the pulse width to the shortest one and start the operation.
When the operation in the shortest pulse is stable then go to
operation in longer pulse and repeat the similar step until the
operation reaches to the final pulse condition.

MDC-5000 Series Used battery and radar disposal
0093153004-00 xiii
Used battery and radar disposal
Treatment of the used lithium ion battery
To dispose of built-in lithium ion battery (CR2032) in this radar, insulate each terminal with tape, and
wrap in plastic bag.
The disposal and collection rules may be different depending on each municipal district. Obey the
directions of each district.
Disposal of this radar
This radar shall be disposed according to the municipal regulations or rules.
A high-energy density lithium ion battery is installed in this radar.
Improper disposal of a lithium ion battery is discouraged as the battery
has a possibility of short-circuiting. If it gets wet, the generation of heat,
explosion or ignition may occur resulting in an injury or fire.

In case no Heading and Speed signals MDC-5000 Series
xiv 0093153004-00
In case no Heading and Speed signals are input from navigation
equipment
When no Heading and Speed signals are input from navigation equipment (in case not connected), this
radar gives alarms and warning messages at lower right of the display, if the radar is started up factory
default settings.
These alarms are disengaged by pressing OFF key temporarily, however, the alarms are activated
again next time the radar is start up.
Disengage the alarm detection function on start up by the following. Once set, the alarm is not detected
next time the radar is started up.
Press MENU key to display “Menu”.
Select [ALARM] => [ALARM ON/OFF] => [I/O] => [HDG INPUT] => [OFF], and press ENT key.
Select [ALARM] => [ALARM ON/OFF] => [I/O] => [SPD INPUT] => [OFF], and press ENT key.
Select [ALARM] => [ALARM ON/OFF] => [I/O] => [LAT/LON INPUT] => [OFF], and press ENT key.

MDC-5000 Series Contents
0093153004-00 xv
Contents
Document Revision History .......................................................................................................i
Important Notice........................................................................................................................ii
For Your Safe Operation.......................................................................................................... iii
Break in procedure of stored radar.........................................................................................xii
Used battery and radar disposal............................................................................................ xiii
In case no Heading and Speed signals are input from navigation equipment....................... xiv
Contents .................................................................................................................................xv
Introduction ............................................................................................................................ xxi
Configuration items............................................................................................................... xxii
System configuration................................................................................................ xxii
Option list ................................................................................................................ xxiii
Chapter 1 Display and Operation............................................................................ 1-1
1.1 Radar Display............................................................................................................ 1-1
Upper left corner ......................................................................................................1-1
Upper right corner ....................................................................................................1-2
Lower left corner ......................................................................................................1-2
Lower right corner .................................................................................................... 1-2
INFO DISP ...............................................................................................................1-3
Alarm status .............................................................................................................1-4
MAP INFO................................................................................................................1-4
1.2 Operation Unit........................................................................................................... 1-6
1.3 Menu usage .............................................................................................................. 1-8
Turn MENU on and off .............................................................................................1-8
Select menu item ..................................................................................................... 1-8
1.4 Cursor Access usage................................................................................................ 1-9
Chapter 2 Radar Basic Operation ........................................................................... 2-1
2.1 Power ON/OFF ......................................................................................................... 2-1
Power ON.................................................................................................................2-1
Power OFF............................................................................................................... 2-1
2.2 Change Brilliance...................................................................................................... 2-2
Display Brilliance...................................................................................................... 2-2
Operation unit Brilliance...........................................................................................2-2
2.3 Transmission............................................................................................................. 2-3
Transmission ON...................................................................................................... 2-3
Transmission OFF....................................................................................................2-3
2.4 Tuning method .......................................................................................................... 2-4
Change MAN (manual) and AUTO...........................................................................2-4

Contents MDC-5000 Series
xvi 0093153004-00
Optimized value setup method.................................................................................2-4
2.5 Change range scale..................................................................................................2-5
Change range unit (NM / km / sm)...........................................................................2-5
2.6 Adjust receiver gain (GAIN) ......................................................................................2-6
Selection of MAN GAIN and AUTO GAIN................................................................2-6
AUTO adjustment of GAIN.......................................................................................2-6
MAN adjustment of GAIN.........................................................................................2-7
2.7 Reject sea clutter (anti-SEA).....................................................................................2-8
Selection of MAN SEA and AUTO SEA....................................................................2-8
AUTO adjustment of SEA.........................................................................................2-9
Manual adjustment of SEA.......................................................................................2-9
2.8 Reject rain/snow clutter (anti-RAIN)........................................................................2-10
Changing method of CFAR and MAN ....................................................................2-11
CFAR (Constant False Alarm Rate) adjustment.....................................................2-11
RAIN MAN (manual) adjustment............................................................................2-12
2.9 Change transmission pulse width (SP/LP)..............................................................2-13
2.10 Select Display Mode................................................................................................2-14
For H UP (Head up mode)......................................................................................2-14
For C UP (Course up mode) ..................................................................................2-15
For N UP (North up mode) .....................................................................................2-16
For relative motion (RM) and true motion (TM)......................................................2-17
Reset true motion...................................................................................................2-18
2.11 Ground and Sea stabilization..................................................................................2-19
SEA (Sea stabilization)...........................................................................................2-19
GND (Ground stabilization) ....................................................................................2-19
2.12 Measurement of distance by RR and VRM.............................................................2-20
Display Range Rings (RR) .....................................................................................2-20
Measurement Range (VRM: Variable Range Marker) ...........................................2-21
Measurement Range (Cursor)................................................................................2-21
2.13 Measurement of bearing by EBL.............................................................................2-22
Using the EBL/VRM OFFSET ................................................................................2-23
2.14 Bearing mode set up...............................................................................................2-24
2.15 Measurement of distance/bearing by PI..................................................................2-25
2.16 Change color and brightness (Day/Night)...............................................................2-26
Setup color .............................................................................................................2-26
Setup USER1 and USER2 color ............................................................................2-27
Setup brightness.....................................................................................................2-28
Color and brightness settings reset........................................................................2-28
2.17 Remove the heading line/navigation data...............................................................2-29