Kogan SMARTERHOME KA52CWCLRWA User manual

KOGAN SMARTERHOME™ 40W
90+ CRI NATURAL COOL &
WARM WHITE CEILING LIGHT
(520MM ROUND)
KA52CWCLRWA

•WARNING: The ceiling light must be installed by a licensed electrician.
•The ceiling light is rated 220-240V. Ensure to the voltage supply at your home
corresponds to this.
•The LEDs of the ceiling light cannot be replaced. Do not disassemble the product.
•The ceiling light generates heat during operation. Keep the surrounding air
convection for heat dissipation.
SAFETY & WARNINGS

Ceiling Light (x1)
Metal Chassis (x1)
Remote Control (x1)
Expansion Tubes (x2)
Self-tapping Screws (x4)
COMPONENTS

Ceiling Light
1
Power Pin
2
Snap Slider
Metal Chassis
1
Threading Hole
2
Screw Fixing Hole
OVERVIEW

Remote Control

1 Indicator Light Emits red light when you press any key.
2 Power On Button
•Short press to turn on the ceiling light. The ceiling
light will automatically return the status before it
was turned off.
•Additionally, this button can be used to
pair/unpair the remote control with the ceiling
light. For instructions, see the Remote Control
section of this user guide.
3 Increase Brightness
•Short press to increase the brightness step by
step.
•Long press to increase brightness gradually.
4 Warm Light
(3000K)
•Short press to increase the colour warmth step by
step.
•Long press to increase the colour warmth
gradually.
5 Night Status
•Set the night light status to Warm Light (3000K)
with 10% brightness.
•Press any key to release from this function.
6 Cyclic Conversion Set the light setting to cyclic conversion:
Cool Light – Medium Warm Light – Warm Light
7 Automatic Turn Off
•Short press this key to set the ceiling light to turn
off automatically after 30 minutes.
•Press any other key to release from this function.
8 Decrease Brightness
•Short press to decrease the brightness step by
step.
•Long press to decrease brightness gradually.
9 Cool Light
(6500K)
•Short press to decrease the colour warmth step
by step.
•Long press to decrease the colour warmth
gradually.
10 Medium Warm Light
(4000K)
Press this key to set the ceiling light to medium
warm light of 4000K with lower brightness.
11 Power Off Short press this key to turn off the ceiling light.

Step 1:
•Open the package and remove the ceiling lamp. Pull the metal chassis outward
and remove it.
•Turn off the power supply to avoid electric hazards.
Step 2A:
To install the light directly into the ceiling:
•Pass the power cable through the threading hole of the metal chassis.
•Fix the metal chassis to the ceiling with expansion screws and self-tapping screws.
•Ensure the metal chassis is fixed firmly.
INSTALLATION
Note: The ceiling light must be installed by a licensed electrician.

Step 2B:
To install the light into an installation point mounted on the ceiling:
•Ensure the installation point is mounted firmly.
•Pass the power cable through the threading hole of the metal chassis.
•Fix the metal chassis to the mount using the self-tapping screws.
•Ensure the metal chassis is fixed firmly.
Step 3:
•Strip 8-10mm of the power cable as shown in the image.
•Insert the stripped end of the power cable into the metal chassis interface.
•Check that the cable is secure and is aligned.
•To remove the power cable, press the red button the metal chassis and remove the
power cable.
Step 4:
•Align the side of the ceiling light so that the opening of the groove is towards the
metal chassis. Slide the ceiling light into the metal chassis completely.
•Push it gently against the ceiling level and you will hear a click sound.
•Ensure the ceiling light is fully seated.
10mm

Install App
Download the “Kogan SmarterHome” app from the Play Store (Android) or App Store (iOS).
Register
If you do not have a Kogan SmarterHome™ account, register or sign in with a verification
code sent by SMS.
To register:
1. Ta p to enter registration page.
2. The system automatically recognises your country/area. You can also select your
country code manually. Enter your email address and tap ‘Next.’
3. Alternatively, you can select ‘Register by mobile number’ and enter the verification
code sent to you by SMS.
4. Create a profile on the next page to define your location and room.
CONNECT TO SMARTERHOME™ APP

Set device in pairing mode
When the device is first turned on, it may automatically enter pairing mode which indicated
by ceiling light flashing rapidly.
If not automatically in pairing mode when powered on, you can manually set the device in
pairing mode by turning on and turning off the wall switch for 3 times until the ceiling light
starts flashing rapidly.
Add device through network
5. Once registered, tap “+” in the upper right corner of the app’s home page to add a
new device through the network.
6. Select the product type from the list of options in the app (Lighting > Indoor Bulb).
7. Ensure that the device is in pairing mode, with the ceiling light flashing rapidly, and
tap “Confirm light is rapidly flashing”.

8. Upon successfully confirming pairing mode, enter your Wi-Fi details. It is important
that your SmarterHome™ device and the app are connected to the same Wi-Fi
network during setup.
9. The device will commence the pairing process and connect to the app. Ensure your
Wi-Fi router, mobile phone, and the SmarterHome™ device are kept close until
connection is complete.
10. After successfully being added, you will have the option to rename the device and
assign it to a location. It will now be listed on the app’s home page. Tap the device
listing to enter its control page.
Notes:
•The device and the app have to use the same Wi-Fi network.
•The device is only compatible with 2.4Ghz networks.

By default, the remote control will be paired with the ceiling light when taken out of the
package. You can also pair and unpair using the Power On button on the remote control.
Pairing with the Ceiling Light
1. Turn off the ceiling light at the wall switch for 10 seconds.
2. Turn on the ceiling light at the wall switch.
3. Within 30 seconds after turning on the light, press and hold the Power On button
on the remote until the light flashes 3 times. Your remote is now successfully paired
with the ceiling light.
Unpairing the Remote with the Ceiling Light
1. Turn off the ceiling light at the wall switch for 10 seconds.
2. Turn on the ceiling light at the wall switch.
3. Within 30 seconds after turning on the light, press and hold the Power On button
on the remote until the light flashes 6 times. Your remote is now unpaired with the
ceiling light.
Group Control using the Remote
You may connect multiple ceiling lights to the same wall switch and pair them to the same
remote control. There is no limit on the quantity of ceiling lights that can be controlled by the
same remote at the same time.
For group control by the same remote, ensure that all ceiling lights are connected to the
same wall switch.
To control/pair the remote with a group of lights:
1. Unpair the remote with each individual ceiling lights as instructed in the Unpairing
the Remote with the Ceiling Light section.
2. Turn off the group of ceiling lights at the wall switch for 10 seconds.
3. Turn on the ceiling lights at the wall switch.
4. Within 30 seconds after turning on the ceiling lights, press and hold the Power On
button on the remote until the lights flash 3 times. Your remote is now successfully
paired with all ceiling lights.
REMOTE CONTROL

Adding “SmarterHome” to the Google Home app
1. From the home page of the Google Home app, select the “+” icon to access the
‘Add and manage’ page.
2. Select ‘Set up device’, then under the Works with Google banner, select ‘Have
something already set up?’
3. Select the search bar and type ‘Smarter Home’ to locate the Kogan
SmarterHome™ service.
GOOGLE HOME CONTROL
Note:
You will need to have set up a Google Home account prior to linking your
Kogan SmarterHome™ device.

4. Tap ‘Authorise’ to grant Google permission to access the SmarterHome™ app and
your devices.
5. From here, you will be prompted to sign into your SmarterHome™ account using
either your email or mobile phone number, depending on which method you used
to register your account.

6. Once connected, the app will display any compatible devices linked to your
SmarterHome™ account. From here you can assign them to rooms and set up any
routines.
7. Tap on any of the devices to view a list of available commands.
Note:
Please note that Google Home can only control the base/core functions of any
compatible SmarterHome™ devices. To make full use of this product’s smart
functionality, please use the Kogan SmarterHome™ app.

Adding “SmarterHome” to the Alexa app
1. From the home page of the Alexa app, select the “ ” icon in the top-right and
select Skills & Games from the sidebar.
2. Select the search bar and type ‘Smarter Home’ to locate the Kogan
SmarterHome™ skill.
AMAZON ALEXA CONTROL
Note:
You will need to have set up an Alexa account prior to linking your Kogan
SmarterHome™ device.

3. Tap ‘Enable to Use’ to add the Kogan SmarterHome™ skill to Alexa.
4. From here, you will be prompted to sign into your SmarterHome™ account using
either your email or mobile phone number, depending on which method you used
to register your account.
5. Tap ‘Authorise’ to grant Alexa permission to access the SmarterHome™ app and
your devices.

6. Once connected, the app will perform a search and display the devices linked to
your SmarterHome™ account.
7. When your devices have successfully connected to the Alexa app, you will be able
to control your Kogan SmarterHome™ devices via Alexa’s voice commands.
Note:
Please note that Alexa can only control the base/core functions of any compatible
SmarterHome™ devices. To make full use of this product’s smart functionality,
please use the Kogan SmarterHome™ app.

Input Voltage 220-240V
Input Power 40 W
Dimensions 520mm
Shape Round
Colour White
SPECIFICATIONS