Kogan SMARTERHOME KATVLTHDMIA User manual

KOGAN SMARTERHOME™
TV LED BACK LIGHT
(WITH HDMI SYNC BOX)
KATVLTHDMIA

Read this user guide and follow all the safety instructions before installation and first use.
• The product is not waterproof.
• Use the product with the provided power adapters only.
• Be cautious of static electricity during installation and usage.
• Keep this product away from sharp objects or strong corrosives.
• When bending the light strip during installation, avoid folding the LED components as
it may affect the life span of the product.
• Remove any nails, metal, or other electro conductive objects from the installation
surface before attaching the strip light. Failure to do so may result in short-circuiting.
• Do not install the strip light near any heat sources.
• Do not allow children to install the strip light without adult supervision.
• Completely unroll the light strip before powering them on.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with minimum distance 20cm between
the product and your body.
Non-replaceable light source.
Not intended for illumination. Only used for creating ambiance.
• Do not connect the light strip to the power supply while it is wound onto a reel.
• Do not cover the light strip.
• Do not open or cut the strip light.
SAFETY & WARNINGS

HDMI sync box
HDMI 2.0 cable
USB cable
LED light strip
Controller
Clip (x10)
Power adapter (x2)
User guide
COMPONENTS

Note: This kit includes 1 HDMI cable. Additional HDMI cables will need to be purchased
separately.
OVERVIEW
Video source
Set-top box
Streaming device
Media player
Gaming console
Controller
HDMI Sync
Box
Power adapter
Power adapter

HDMI Sync Box
HDMI IN
Connect to media source (streaming device, gaming console etc.)
HDMI OUT
Connect to TV
DATA OUT
Connect to controller.
POWER
HDMI IN
HDMI OUT
DATA OUT
Set-top box
Streaming device
Media player
Gaming console
TV
Controller
Video source

Controller
Power Button
• Press to turn the system On/Off
• Press and hold the Power button for 5 seconds until the green
indicator is off. After approximately 1-2 seconds, the green
indicator will begin flashing. The system is now in Wi-Fi pairing
mode.
Sync Button
Press to sync the lights to the input source. Press again to stop
syncing.
Light
Connect to LED light strip.
DATA
• Connect to HDMI sync box “DATA OUT” port.
• The second USB port is used to connect to an additional device
(light bars, floor lamps etc.) Note: Additional devices purchased
separately.
Power
Connect to Power adapter.
HDMI Sync Box
Power Adapter
Sync Button
Power Button
LED Light Strip

Step 1.
• Unbox the product checking all items listed in the components list are present.
• Unroll and power on the LED light strip to ensure it lights up.
Step 2.
Wipe the installation surface to ensure it is clean and dry.
INSTALLATION
Rear of TV/Monitor

Step 3.
Starting from the bottom left corner, attach the LED light strip to the rear of the TV. Press
the strip firmly and then secure it in place using the supplied clips.
Step 4.
• Insert the LED light strip connector into the “LIGHT” port on the controller.
• Connect the Power Adapter and USB cable to the controller.
• Using 3M tape attach the controller to a wall or rear of the TV.
Left
Right
Rear of TV/Monitor
Notes: The LED light strip must be installed starting from the bottom left corner of the
rear of the TV, in clockwise direction.
LED light
strip
Power adapter
USB Cable

Step 5.
• Connect the USB cable from the controller into the “DATA OUT” port on the HDMI
sync box.
• Connect the HDMI sync box to the TV using the supplied HDMI cable.
• Connect the media source (gaming console, streaming device etc.) to the “HDMI IN”
port on the sync box using an HDMI cable (not supplied).
• Connect the Power Adapter to the HDMI sync box.
• Power on both the controller and HDMI sync box.
POWER
HDMI IN
HDMI OUT
DATA OUT

Install App
Download the “Kogan SmarterHome” app from the Play Store (Android) or App Store (iOS).
Play Store (Android)
App Store (iOS)
To register:
1. If you already have a SmarterHome account, select ‘Log In’. To register a new
account, select ‘Sign Up’.
2. The system will automatically recognise your country. If needed, you can manually
select your country from the drop-down box. Enter your email address and tap
‘Get Verification Code’ to continue.
3. A 6-digit code will be sent to the submitted email address. Enter this code before
the one-minute timer expires.
4. Continue to the next page and complete your SmarterHome profile.
CONNECT TO SMARTERHOME™ APP

Set device in pairing mode
When the device is first turned on, it may automatically enter pairing mode (indicator is
flashing green).
If not automatically in pairing mode when powered on, you can manually set the device in
pairing mode by pressing and holding the Power button for 5 seconds until the green
indicator is off. After approximately 1-2 seconds, the green indicator will begin flashing.
Add device through network
1. Once registered, tap “Add Device” on the app’s home page, or the “+” in the upper
right corner, to add a new device through the network.
2. Select the product type from the list of options in the app (Lighting > HDMI TV
Light).
3. Enter your Wi-Fi details. It is important that your SmarterHome™ device and the
app are connected to the same Wi-Fi network during setup.
Notes:
• The device and the app have to use the same Wi-Fi network.
• The device is only compatible with 2.4Ghz networks.
• Depending on the product, Steps 3 and 4 may be in opposite order.

4. Ensure that the device is in pairing mode, with the indicator flashing green, and
tap “Confirm light is rapidly flashing”.
5. The device will commence the pairing process and connect to the app. Ensure
your Wi-Fi router, mobile phone, and the SmarterHome™ device are kept close
until connection is complete.
6. After successfully being added, you will have the option to rename the device and
assign it to a location. It will now be listed on the app’s home page. Tap the device
listing to enter its control page.
Note:
Once connected, you can select Create Scene from the “+” in the upper right
corner (or from the Scene tab) to group connected SmarterHome™ products
and automate their functions.

HDMI sync box power supply
DC5V=1.5A
Controller power supply
DC12V=1.5A
Suitable TV size
55-65 inches
LED light strip length
3.8m
Light strip water resistance
IP44
Wi-Fi
IEEE 802.11 b/g/n
Bluetooth
4.0
Operating frequency
2.412~2.484GHz
Support system
Android 5.0 or iOS 9.0 and above
1. The adhesive tape is not holding.
• Ensure the installation surface is clean and dry.
• Firmly press over the strip after sticking.
• Reinforce the installation using more clips and 3M tape.
2. Cannot connect to Wi-Fi.
Ensure that your phone has both Wi-Fi and Bluetooth turned on before attempting to pair.
Only 2.4 GHz Wi-Fi signals are supported. 5.0 GHz networks will not work.
3. Lights are not syncing with the TV.
• Ensure you have installed the LED light strip in the clockwise directions starting
from the bottom left corner of the rear of the TV.
• Ensure you have connected the HDMI box and it is powered on.
SPECIFICATIONS
TROUBLESHOOTING

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com