Kohler 10868T-B4 User manual

1338602-2A-A 1
BEFORE YOU BEGIN
INSTALLATION INSTRUCTIONS
10868T-B4 Deck-Mount Bath & Shower Faucet10868T-B4 Deck-Mount Bath & Shower Faucet
SINGULIER
HANDLE OPERATION
Lift the handle gently. Turn clockwise for hot water, Turn counter-clockwise for cold water. Water flows out from
spout when faucet diverter is in the normal position and it’s diverted to handshower when the diverter is lifted.
ROUGH-IN DIMENSIONS
Special model meets or exceeds the following at date of manufacture: TIS
STANDARD APPLICABLE
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1.Flush the water supply pipes thoroughly to remove debris.
2.The minimum inlet water pressure for the diverter is 0.05MPa(0.5bar).
3. The highest working pressure for handshower & showerhead is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar),
a pressure reducer is needed. The highest water and environment temperature is 60ºC. Please keep handshower,
showerhead and shower arm away from heater, or it may become damaged and cause injury to the user.
1338602-2A-A 4
SINGULIER
SERVICE PARTS
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
G1/2˝
G1/2˝
1500
40°
58
40
22.5
50
150
G1/2˝
185
137
9º
69
Max.27
59
1059041**
831727**
880010
1295534**
3006116
1072544**
1285497**
3025890
880002**
CP:3005771**
AF/BN:1207769**
1287332
3015522
880086
871568
3015536
834793
870760
871363
1294005
870495
3006142**
3006338
834404
870393
831366
860091
834638
1297467**
1030624
1240266
77420
Ø28
240
250
G1/2˝

1338602-2A-A 2 1338602-2A-A 3
INSTALLATION
How to Install the Handshower
Remove the guard on the outlet connector firstly.
Put the washer(9-1) into end A of the hose(10), and then connect to the
faucet outlet(11). Put the washer(9-2) into end B of the hose, and install
the restrictor(12) into the handshower(13) inlet if needed, then connect
end B of the hose to the handshower inlet.
How to Install the Faucet
Install the deck-mount connection(1) onto the connector(3) and adjust the
position as shown. Put the fixing screw(2) into the hole of the connection
and tighten with the wrench(4).
Put the washer(5) into the groove of the deck-mount connection, and
then install the connections into the hole of the bath tub. Thread the
washer(6)(7), nut(8) onto the shank of the connection from the underside
of the bath tub. Tighten the nut(8).
12
5
3
4
6
7
8
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
Ensure that all coupling nuts are tightened. Ensure that the handle is in the off position. Turn on the drain and main
water supply, and check for leaks. Repair as needed.
Remove the handshower. Remove the aerator by coin. Run hot and cold water through the faucet for about one
minute to remove any debris. Check for leaks. Remove any debris from the aerator assembly. Shut the faucet off,
and reinstall the aerator assembly and handshower.
How to Install the Bracket
Determine a suitable location on the finished wall to install the bracket.
Mark bracket base mounting hole locations on the wall according to the
dimension. Drill two holes on the finished wall, the holes should match
the anchors(17). Install the anchors. Tighten screws(16) to secure
bracket base(14) to the finished wall. Put the bracket(15) onto the bracket
base and lock by stopper. Hang the handshower on the shower bracket.
22.5mm
17
16
15
14
10
9-2
11
9-1
12
A
B
13
Katalyst Air
Intense Massage
How to Operate the Handshower
Press the buttons of the handshower to change the water flow.
How to Maintain the Handshower
Any debris or mineral build-up may cause the flow stream to become
distorted or reduce the flow rate. To remove the debris or mineral build-up,
run water through the handshower, firmly press or rub your finger back
and forth across the rubber nozzles.
Remove and clean the screen washer.