Kohler K-6330 User manual

Installation Guide
Kitchen Sink Faucet
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page“ Français-1”
Español, página“ Español-1”
K-6330
1025493-2-B

Tools and Materials
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and web site are listed on
the back cover. Thanks again for choosing Kohler Company.
Before You Begin
Do not attach a dishwasher to the faucet spray outlet.
Observe all local plumbing and building codes.
Shut off the water supplies.
Carefully inspect waste and supply tubing for any sign of
damage and replace if necessary.
For new installations, assemble the faucet on the sink before
installing the sink.
Before installation, unpack the new faucet and inspect it for
damage. Return the faucet to the carton until you are ready to
install it.
Do not remove the faucet ground joints, as they contain
important back-siphonage protection.
Kohler Co. reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
Pencil Level
Assorted
Screwdrivers
Adjustable
Wrench
Tape
Measure
1025493-2-B 2 Kohler Co.

1. Supply Installation
NOTE: This spout and valve can be installed from 4″(10.2 cm) to 8″
(20.3 cm) between center-to-center.
NOTE: The water supply lines must be offset to the right or left as
shown to avoid interference with the pulley cover.
Install the water supplies and drain line according to the
illustration.
Flush the water supplies and stops.
2. Faucet Installation
Install the rubber gasket to the underside of the valve.
Fit the valve through the desired sink hole.
Position the valve so the handle faces forward.
Thread two screws into the threaded ring until they barely
protrude from the top of the threaded ring.
Fit the fiber washer and metal washer to the valve shank.
Install the threaded ring to the valve shank until the threaded
ring is just touching the sink.
Turn the threaded ring so the screws are to the front and back of
the faucet.
Securely tighten the screws.
Install valve to
right or left of
spout.
Pulley Cover Drain Line
Water
Supplies
Valve
Inlet
Sink
Screw
Valve
Shank
Rubber
Gasket
Fiber Washer
Threaded Ring
Metal Washer
Kohler Co. 3 1025493-2-B

3. Complete the Faucet Installation
Thread the two screws into the threaded ring until they barely
protrude from the top of the threaded ring.
Install the rubber gasket to the underside of the spout.
Fit the spout through the sink hole.
Position the spout so that it faces forward. The Kohler logo
should be facing the user.
Fit the fiber washer and metal washer on the spout shank.
Install the threaded ring to the spout shank until the threaded
ring is just touching the sink.
Turn the threaded ring so that the screws are to the front and
back of the spout.
Position the spout to obtain the desired range of rotation.
Securely tighten the screws.
Spout
Sink
Screw
Threaded
Ring
Fiber Washer
Rubber Gasket Spout Shank
Kohler Logo
Metal Washer
1025493-2-B 4 Kohler Co.

4. Position Channel
NOTE: Metal and plastic components may have sharp edges and
corners. Handle these parts carefully.
Fit the channel over the spout shank with the open end facing the
valve.
Insert two square-head bolts through the top holes in the channel.
Install the washers and hex nuts over the two square-head bolts.
Position the top of the channel so that it is even with the bottom
of the spout shank threads.
Securely tighten the hex nuts with a wrench.
Channel
Washer
Spout Shank
Hex Nut
Square-Head Bolt
Kohler Co. 5 1025493-2-B

5. Angle Bracket Installation
Install the angle bracket to the bottom of the channel with the
square-head bolt, washer and hex nut.
Hand tighten the hex nut. Do not tighten with a wrench at this
time.
When installing faucet with a stainless steel sink:
Use a level to make sure that the spout is plumb.
Position the channel as needed.
When installing faucet to any other sink:
Adjust the height of the angle bracket so that it rests on the
cabinet floor.
Secure the angle bracket to the cabinet floor with two screws
suitable for the material.
Securely tighten the angle bracket hex nut with a wrench.
Angle
Bracket
Square-Head
Bolt
Channel
Washer
Hex Nut Hex Nut
Screws
Channel Cabinet
Floor
1025493-2-B 6 Kohler Co.

6. Handspray Installation
Cover the sprayhead with clean packing wrap to protect it from
damage during installation.
Insert the spray hose into the spout.
Fit the gasket into the valve outlet.
Hold the valve outlet in place with a wrench.
Thread the spray hose to the valve outlet. Hand tighten only.
Remove the packing wrap from the sprayhead.
Open the valve. Water will flow from the sprayhead.
Check for leaks. Adjust as needed.
Test the water flow of the spray control. Water flow will increase
when the handle is pushed lightly inward. Water flow will stop
when the handle is pushed fully inward.
Close the valve.
Gasket
Spray
Hose Channel
Valve Outlet Spout
Sprayhead
Kohler Co. 7 1025493-2-B

7. Checkout Installation
Position a large plastic washer on each side of the pulley.
Fit the pulley over the spray hose, then inside the channel.
Install a plastic cover to each side of the channel.
Secure the plastic covers together with a bolt, washer, and wing
nut.
Hand tighten the wing nut onto the bolt. Do not overtighten.
Pull the sprayhead out of the spout several times to verify
smooth, unrestricted spray hose movement.
Channel
Spray Hose
Pulley
Wing Nut
Washer
Bolt
Large Washer
Large Washer
Cover
1025493-2-B 8 Kohler Co.

8. Water Temperature Adjustment
NOTE: Before adjusting the water temperature, ensure that the
handle is turned all the way to the left. This is the maximum hot
position.
Loosen the setscrew.
Remove the handle and bonnet.
Turn on the water to the maximum temperature by pushing the
valve stem up and turning it clockwise.
Mark the current position of the temperature stop tab (top edge)
on the mounting nut with a marker or pencil.
Lift the indexer and top disc just enough to clear the valve
splines and to allow rotation.
NOTE: Each spline notch is an average 9.5° F (5.3° C) change in
temperature.
Turn the indexer, top disc, and valve stem counterclockwise until
the desired temperature is achieved.
Reinstall the indexer and top disc to the valve, making sure the
top disc is snapped fully into the indexer.
Turn off the water by pulling the valve stem down.
Reinstall the bonnet and handle.
Tighten the setscrew.
Top Disc
Indexer
Handle
Setscrew
Bonnet
Mounting Nut
Splines
Valve Stem
Stop Tab
Kohler Co. 9 1025493-2-B

Guide d’installation
Robinet d’évier de cuisine
Outils et matériels
Merci d’avoir choisi la compagnie Kohler
Nous apprécions votre engagement envers la qualité Kohler. Veuillez
prendre s’il vous plaît quelques minutes pour lire ce manuel avant de
commencer l’installation. Ne pas hésiter à nous contacter en cas de
problème d’installation ou de fonctionnement. Nos numéros de
téléphone et adresse internet sont au verso. Merci encore d’avoir choisi
la compagnie Kohler.
Avant de commencer
Ne pas connecter un lave vaisselle à la sortie du vaporisateur du
robinet.
Respecter tous les codes de plomberie et de bâtiment locaux.
Couper les alimentations d’eau.
Vérifier avec soin si l’évacuation ou les tubes d’alimentation pour
déceler tout signe d’endommagement et remplacer si nécessaire.
Pour de nouvelles installations, installer le robinet sur l’évier
avant d’installer ce dernier.
Avant l’installation, déballer le nouveau robinet et l’examiner
pour en déceler tout dommage. Remettre le robinet dans son
emballage de protection jusqu’à être prêt à l’installation.
Tournevis
assortis Mètre ruban
Crayon à
papier Niveau à
bulle
Cléà
molette
Kohler Co. Français-1 1025493-2-B