Kohler ESCALE K-19611T User manual

-1-
ESCALE
INSTALLATION INSTRUCTIONS
VANITY TOP CABINET
K-19611T, K-15455T, K-19612T
BEFORE YOU BEGINBEFORE YOU BEGIN
IMPORTANT !
·Installer: This manual is the property of the customer and
must be retained with the product for maintenance and
operational purposes.
Cabinets are very heavy. Get help lifting and moving the
cabinets.
NOTE
·
·
·
·
·
·
·
Turn off the water supply.
The plumbing installation must comply with all local water
supply and building regulations.
Before installation carefully inspect the new fixture for any
signs of damage.
Ensure all required electrical work has been completed
before installing the furniture.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain import care, cleaning, and
warranty information please leave these instructions for
the consumer.
Escale bathroom cabinet includes a series of washbasin
cabinet with visible surfaces of oak grain. The series
adopt E1 grade wood-based panel of high quality, and
with further processing, its harmful emissions will be less
than 1.5mg/L. Washbasin cabinets with single door and
double doors are available.
·
·
·
·
·
·
·
·
E1
1.5mg/L
ORDERING INFORMATION
Escale Vanity Top Cabinet.........................................K-19611T
Bathroom Furniture Legs ..........................................K-15455T
Escale Vessel Cabinet RH ........................................K-19612T
This installation and user guide covers the installation of the
following for the Escale range:
..............................................K-19611T
................................................................K-15455T
( ) ....................................K-19612T
215500
, 2009
Copyright Kohler China Ltd., 2009
1038407-T01-D

-2-
SAFETY: WARNINGS
Kohler products are precision-engineered and should give
continued superior and safe performance, provided:
1. They are installed, commissioned, operated and
maintained in accordance with the recommendations given
in this Manual.
2. Periodic attention is given, as necessary, to maintain the
product in good functional order. Recommended guidelines
are given in the section.
Carefully inspect the new fixture for any signs of damage.
When installing Kohler Products, manufacturers guidelines for
power tool safety should be followed.
MAINTENANCE
1.
2.
ROUGHING-IN
Unit: mm
K-19611T
1000 355
510
K-19612T
510
500
500
1038407-T01-D

-3-
80
80
225
6
4
225
6
K-15455T
INSTALLATION
SPECIFICATION
Plumbing Connections
Hot (H) and Cold inlets must be connected to the correct
inlet pipes.
(H) (C)
()
C
Install the Plumbing
Install the drain in accordance with the manufacturer,s
instructions.
Make sure a watertight seal exists on all
basin drain connections.
Provide access to the plumbing connections
for future plumbing maintenance.
The hot and cold water supplies must be installed with
isolating valves.
Caution!
Caution!
Note!
1.
()
Install the Vanity Top Cabinet
1. Decide on the location of the cabinet, and mark the
dimensions of the wall hanging brackets to the dimensions
given.
Make sure that you avoid hidden cables and
pipes when you drill holes in the wall.
For the vanity top cabinet, make sure that you mark the
positions on the wall for the attachment bolts. (Refer to
countertop installation instructions for further information).
Caution!
Note!
1038407-T01-D

-4-
2.
2. For installations, you must use suitable
attachment bolts and wall plugs to secure the unit to the wall.
Tighten bolts using an hexagonal wrench.
Solid Wall
360mm 280mm
957mm
20mm
510mm
236mm
661mm
()
(Inner Distance Between
Side Boards)
Vanity Top Cabinet
20mm
781mm
3.
3. Using a suitable drill, drill the holes for the wall hanging
brackets. Secure the brackets to the wall with the
appropriate wall plugs and Screws.
510mm
1000mm
4. Carefully unscrew the doors from the cabinet, and lift the
doors off the hinges. Place the doors carefully to one side.
4.
5. /
5. Fit the cabinet/basin unit in position on the wall, lifting it
over the wall hanging brackets.
2
1
1038407-T01-D

11.11. Adjust the screw at each end of the back panel until it is
upright.
-5-
12.
13.
12. Fit the shelf supports in position in the pre-drilled holes.
13. Fit the shelf.
14. /
14. Refit the cabinet/basin unit doors onto the hinges, and
tighten the screws. Ensure the doors are level, and adjust
the screws in the hinges Accordingly.
2
1
6.
7. /
8.
9. /
10.
6. Level the cabinet by adjusting the adjustment screws. The
top screw will adjust the cabinet vertically, and the bottom
screw will adjust it horizontally.
7. Ensure the vanity top is seated in the correct position and
is secure.
8. Use a spirit level to ensure the cabinet is level.
9. Place the basin in the desired position on the cabinet/basin
unit.
10. Install the back panel
1038407-T01-D

-6-
Install the Undermounted Unit
1. Decide on the location of the unit, and mark the
dimensions of the wall hanging brackets to the dimensions
given.
2. Use a spirit level to ensure the wall hanging brackets are
level.
1.
2.
510mm
236mm
661mm
20mm
457mm
20mm
()
(Inner Distance Between
Side Boards)
Caution!
Solid Wall
Make sure that you avoid hidden cables and
pipes when you drill holes in the wall.
3. For installations, you must use suitable
attachment boltsand wall plugs to secure the unit to the
wall. Tighten bolts using an hexagonal wrench.
4. Using a suitable drill, drill the holes for the wall hanging
brackets. Secure the brackets to the wall with the
appropriate wall plugs and screws.
3.
4.
1038407-T01-D

-7-
5. Carefully unscrew the doors from the undermounted unit,
and lift the doors from the hinges. Place the doors carefully
to one side.
6. Screw the attachment brackets into the required locations
in the undermounted unit. These brackets fit over the wall
hanging brackets to hold the unit in position.
5.
6.
7. Lift the undermounted unit into position on the wall, making
sure the attachment brackets fit into the wall hanging
brackets.
8. Secure the attachment brackets with the screws, and
adjust the screws accordingly until the unit is level. Use a
level to ensure the unit is level.
9. Install the back panel onto the undermounted unit, and
secure in postion with the screws. Adjust the screws to
make sure that the back panel is upright.
7.
8.
9.
10. Apply a bead of silicone sealant aound the opening in the
top of the undermounted unit.
11. Place the washbasin into the opening, and press down
firmly into position.
12. Carefully remove any excess silicone sealant.
13. Refit the undermounted unit doors on the door hinges,
and ensure the doors are fitted scurely and are level.
10.
11.
12.
13.
2
1
1038407-T01-D

-8-
Finish the Installation
1. Fit the handles to vanity top cabinet, vanity basin unit,
undermounted unit and pedestal unit.
2. Place the handle on the front of the unit, and secure in
place using two screws.
1.
2.
3.
4.
5.
6.
7.
3. Fit the tap to the basin in accordance with the
manufacturer,s instructions.
4. Connect the hot and cold water supplies.
5. Attach the waste, and tighten securely.
6. Open the hot and cold water valves, and check the supply
connections for leaks.
7. Run water into the basin, and check the drain connections
for leaks.
HOT COLD
1038407-T01-D

-9-
USER MAINTENANCEUSER MAINTENANCE
1.
2.
3.
4.
5. PU .
6. .
7.
8.
Cleaning
Caution! Risk of product damage. Many cleaners
contain abrasive and chemical substances, and should
not be used for cleaning stainless steel, enamel,
plated or plastic fittings. These finishes should be
cleaned using a mild washing up detergent or soap
solution, rinsed and then wiped dry with a soft clean
cloth.
1.
2.
3.
4.
5. The cabinet door and interior are constructed of mirror and
aluminum. Use only a damp cloth to clean. Spray the cloth,
not the mirror when cleaning. Mirrors are damaged by the
use of ammonia or vinegar based cleaners. Rubbing
alcohol can be used for stubborn stains.
6. Use no abrasive cleansers on any part of the cabinet.
7. The white frame should be cleaned with a damp cloth only.
8. If any fixtures caused by abnormal reasons, Kohler China
can supply paid replacement for service parts caused by
abnormal reasons as shown in the next page in the limited
duration of warranty.
Many cleansers contain abrasive and chemical substance
which is not suitable for cleaning stainless steel, enamel,
plating or plastic products. You may use mild cleansers or
soaps to clean the surfaces. Wipe any splashes of cleaner
solutions from the surface with clean soft cloth.
Maintain ventilation in the bathroom, and separate the dry
area from the damp one if conditions permit. Try to open
the door and windows of the bathroom and maintain good
ventilation.
Kohler bathroom cabinet are dealt with strict procedures
for damp-proof, whose good damp-proof function ensures
good performance even in bathroom of huge humidity. Yet
do not splash and pour water directly on the bathroom
cabinet. Make sure that the bathroom is not over damp
and wipe any splashes from surfaces immediately.
Maintenance of door board: Clean and wipe door board
regularly, and wipe the condensation vapor with dry and
soft cloth.
1038407-T01-D