Kohler STANCE User manual

13-1 528437
INSTALLATION INSTRUCTIONS
8mm
PIVOT DOOR, SCREEN, 1 D2P, 8mm
K-37468T
STANCE
-1-
, 2010
Copyright Kohler China Ltd., 2010
BEFORE YOU BEGINBEFORE YOU BEGIN
·
·
·
·
·
·
3
(
) 50~80mm
3mm/m
·
·
·
·
·
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 3 for reference.
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
Tempered glass cannot be cut, drilled or
knocked by hard object. Make sure corner area
of the glass refraining from knocking so as to
cause personal injury due to broken glass.
Please install this door on Kohler
receptors or curbs. (Not included). If the curb is not
Kohler-branded, please note its top width should fall
within the range of 50~80mm.
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won t take responsibility of the installation
quality.
please leave these
instructions for the consumer.
CAUTION: Risk of injury or product damage.
ATTENTION:
IMPORTANT:
1160469-T01-A

-2-
ROUGHING-IN
Unit: mm
BH
SKU
K-37468T 1200-2000 1850-2000
H
B
800-820-2628
IMPORTANT
800-820-2628
The wall channel for the side panel is delivered to the
door assembly. Remove the panel wall channel before
installing the door, but do not remove the transit blocks.
Before installation check that all components are
correctly supplied.
If any parts are missing please ring the helpline.
PARTS IDENTIFICATIONPARTS IDENTIFICATION
1160469-T01-A

-3-
Cover Cap
Frame Cap, Bottom
X2
Frame Cap, Top
X4
Pivot Caver, Bottom
Pivot Caver, Top
Glass Shelf
X2
Handle Assy.
Pivot Pin
X2
Wall Frame
Wall Jamb
Side Panel
Magnetic Seal
Bottom Frame
Side Seal
Top Frame
Door Glass
Insert Edg
·
·
·
·
·
·
·
·
·
·
·
·
·
Phillips Screwdriver
Pencil
Caulk Gun
Measuring Tape
Safety Glasses
Center Punch
Hammer
Knife
Masonry Drill & 6mm Drilll Bit
Level
Drop Cloth
Materials Required
Tape
Silicone Sealant
Tools Required
·
·
·
·
·
·
·
·
·
·
·
·
·
6mm
INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS
4mm Allen Key
4mm
X6
X10
X6X4
Cover
X6
1160469-T01-A

-4-
INSTALLATION
STEP
1
Fix one side of the wall jamb.
The wall jamb
be kept
vertical.
must
0mm
6mm
STEP
2
Line on the other side. Drill a pivot hole, then insert
wall anchor.
The wall jamb
be kept
vertical.
must
6mm
0mm
STEP
4
STEP
3
Fix both top and bottom frame to the side wall frame. Insert another wall jamb into the side wall frame.
Frames raised
shall face outside.
Note:
The side
of the wall
frame with hole
shall face
inside.
Note:
1160469-T01-A

-5-
Insert the whole set of the frame into the wall jamb. Across through the frame with screw, then fix the wall
jamb.
STEP
6
STEP
5
STEP
7
Please first insert the glass into the top frame and then into the bottom frame.
Please insert the glass in the correct direction: the
end with the hole shall be close to the top frame
and the labeled side with arrows on the label shall
be against the wall.
1160469-T01-A