Kohler VOLUTE K-18669T User manual

-1-
VOLUTE
INSTALLATION INSTRUCTIONS
FILLER DRAIN
K-18669T/K-20609T
!
!
Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
!
!
BEFORE YOU BEGINBEFORE YOU BEGIN
NOTES
!
!
!
!
!
Observe all local plumbing and plumbing codes.
Inspect waste and supply tubing; replace if
necessary.
The drain has removable parts.
Drain T is reversible for vertical or horizontal
drainage.
Do not use sharp and hard objects when taking out
the drain plug to avoid scratching it.
""
!
!
!
!
!
T
Tools Required
!
!
!
!
!
!
Assorted screwdrivers
Adjustable or open end wrench
Pipe wrenches
Pliers
Manual hacksaw
Long flat nose pliers
!
!
!
!
!
!
SHANGHAI KOHLER LTD., NO.368, MIN LE ROAD,
FENG XIAN DISTRICT, SHANGHAI, CHINA POST CODE 201419
368 201419
©
©
Copyright Kohler China Investment Co., Ltd. 2017
2017
1260255-T01-D

ROUGHING-IN
Fig.#1
1
-2-
INSTALLATION PREPARATIONSINSTALLATION PREPARATIONS
Fasten the hose to the water inlet of the overflow base.
Fig.#2a
2a
Fig.#2b
2b
Fig.#3
3
Un-Assemble the spout from the overflow base.
Important: The spout is fit tightly with the overflow
base. Use the straight screw driver to pry the spout
out slightly.
Kohler reserves the right to change marked dimensions without prior notice.
Reference Value UNIT: mm
294 For K-18669T/ K-18669T
263 For K-20609T/ K-20609T 55
X
Y
103
247
OD38
600
OD41.5
X+Y=718 For K-18669T/ K-18669T
X+Y=778 For K-20609T/ K-20609T
Plastic Barcket
Metal Barcket
Spout Kit
Clamp Kit
Screw
18.4
91 For
71
K-18669T/ K-18669T
For K-20609T/ K-20609T
56
1260255-T01-D

-3-
Fig.#5
5
Attach the gasket to the overflow ell, as shown. Apply
silicon sealant.
INSTALLATION
Gasket
Drain Ell
Bath
Wrap the plier head with adhesive tape and then insert
it into the top of the strainer to tighten the drain ell
securely, as shown. Make sure the drain ell tube is
facing the front of the bath. Then apply silicone sealant
around the strainer.
Fig.#6
6
Fig.#8
8
Insert strainer into the gasket, position plain gasket
between the drain ell and the bottom of the bath. Turn
the strainer into the drain ell. Strainer Gasket
Fig.#7
7
Long Flat Nose Pliers
Strainer
Assemble the overflow pipe, drain body and drain pipe
together.
For vertical drainage installations: Assemble parts as
shown. Align the parts with the drain base. Align and
tighten the nuts.
For horizontal drainage installations: Assemble parts as
shown. Align the parts with the drain base. Align and
tighten the nus.
Fig.#4
4
Apply Silicon Sealant
Gasket
Overflow Base
Overflow Pipe
1260255-T01-D

-4-
Insert the spout into the overflow body, fasten the
clamp with screw as shown.
Fig.#10
10
Fig.#11
11
Fig.#12
12
Fig.#13
13
Fasten all the screws.
Fasten the control wire kit to the overflow cover kit, by a
nut.
Assemble the plastic/metal bracket back to the overflow
base from the inside of bath tub as shown.
Important: The arc edge of the plastic bracket
should not lower than the lower edge of overflow
hole, otherwise the button could not function well.
Fig.#9
9
Insert the control wire into the overflow hole.
Plastic Barcket
Metal Barcket
Screw
Insert Screw Here
Clamp Kit
Spout Kit
Lower Edge of
Overflow Hole
Arc Edge of
Plastic Bracket
Nut
Overflow Cover Kit
Control Wire Kit
Screw
1260255-T01-D

Fasten the trigger kit on the strainer.
Push the button on overflow, so the ejector pin of the
trigger kit on high position, then push the plug on the
trigger kit until a "click".
Fig.#17
17
Fig.#18
18
Cross Wrench
Fasten Clockwise
Trigger Kit
Strainer
Plug
Push Down
Trigger Kit Ejector
Remove the rubber cover from the wire as shown, then
fasten the control wire with the trigger kit.
Fig.#16
16
Fasten As Shown
-5-
After insert all the control wire, push the push-botton
base in to the base until a "Click”.
Fig.#14
14
Please align the snap-fit.
Pull the tail of control wire from the drain hole.
Fig.#15
15
Pull Out
1260255-T01-D

Fig.#19
19
Fig.#20
20
Fig.#21
21
Fig.#22
22
Apply Silicon Glue
Pipe on Floor
Seal
-6-
Fasten the hose to the water outlet of the faucet
Option1 Fasten the hose to the water outlet of the
faucet 72681T-ZX-CP
1 72681T-ZX-CP
Option2 Fasten the hose to the water outlet of the
faucet 72681T-ZY-CP
2 72681T-ZY-CP
Option3 Fasten the hose to the water outlet of the
faucet 14675T-ZS-CP
3 14675T-ZS-CP
Option4: Fasten the hose to the water outlet of the
faucet according to the user guide of the faucet.
4
Cold
Cold
Hot
Hot
1260255-T01-D

Attention:
After install, push the button repeatedly, make sure the
plug could open and close normally. Run water into the
bath, check the drain connections for leaks.
MAINTENANCE
Fig.#23
23
!
!
Pull off the plug, unscrew the trigger kit, pull the
control wire out to clean the hair on the wire.
The accessories should be washed with warm water
and a soft cloth or sponge. Do not use abrasive
cleaners or cleaners containing bleach.
!
!
Pull Out
Plug
Strainer
Cross Wrench
Unscrew Counterclockwise
Trigger Kit
Strainer
-7-
1260255-T01-D