Kohler K-5401KR User manual

Installation Guide
설치 지침서
VEIL INTELLIGENT TOILET
베일 일체형 스마트 좌변기
K-5401KR
English page 2-16
한글 페이지 17-31
1243902-KR01-D
KOHKOHLER CHINA INVESTMENT CO., LTD.
NO.158, JIANG CHANG SAN ROAD, JING'AN DISTRICT,
SHANGHAI, PRC POST CODE: 200436
MAMANUFACTURER: SHANGHAI KOHLER ELECTRONICS., LTD.
NO. 1955, FENGXIANG ROAD, BAOSHAN AREA, SHANGHAI, PRC
POST CODE : 20044

面遇到任何問題，務必請您與我們聯繫。
1
2
Product inlet hose
Product tee valve
Assorted screwdrivers
Screw（match with 10mm anchors）
Expansion Bolt Kits
These instructions contain important care, cleaning, and warranty information - please leave instructions for the
consumer.
We appreciate your commitment to Kohler quality. Pleas
e take a few minutes to review this manual before
installation. If you encounter any installation or performan ce problems, please don't hesitate to contact us.Thanks
again for choosing Kohler Company.
Pre-arrange enough space for toilet installation. Make su
re it will not affect the opening and closing of the door.
Confirm the rough in 305mm，
it need reach to 292~350mm，otherwise it may affect installation.
Confirm the distance the water outlet connector away from the finished wall: upper the surface of finished wall by
3mm and lower the surface of finished wall by 5mm otherwise it may affect installation.
Recommend using the main inlet hose at least DN15mm to make sure the following request of water supply conditions.
Measure water conditions before buying the product, there are two measure ways as following.
Note If combined with other faucets in the bathroom, make sure the water condition meets minimum requirement.
Use the hose and Tee valve of this toilet.
3Make sure meet the following water supply condition request before installation.
Simple way to measure water volume:
Prepare a bucket. Fully turn on the tee valve. Firstly flush three times andtest. Fill the bucket with water into
the bucket for 10 seconds. The mininum water volume is advised to be above 5.7L.
Fig.#1
TOOLS AND MATERIALS REQUIRED (Not supplied)
254mm adjustable wrench
Tape measure
Masking tape
Knife
VEIL
K-5401KR
BEFORE YOU BEGIN
Please read the following instructions carefully and familiarize yourself with the required tools, materials, and
installation sequences. Follow the section that pertain to your particular installation. This will help you avoid costly
mistakes. In addition to proper installation, please also read all operating and safety instructions.
All information in the instructions is based upon the latest product information available at the time of publication.
Kohler China reserves the right to make changes in product characteristics, packaging, or availability atany time
without notice.
INSTALLATION INSTRUCTIONS
INTELLIGENT TOILET
1243902-KR01-D
2
Kohler Co.

WARNING: Must use 10A receptacle.
Simple way to measure water volume 2:
Fig.#2
...............................................................................................................K-5401T
..........................................................................................1106433
There is a wiring schematic on the inside of the of the junction box cover.
Observe all local plumbing and building codes.
Carefully inspect the new toilet for damage.
Water and electrical supplies may be wall mounted.
WARNING: Risk of electric shock for hardwire install ations/through-floor electrical sup,ply:
Connect only to properly-grounded, dedicated 220V-240V~, 10A, 50/60Hz circuit protected
by a Class A Ground-Fault Circuit-Interrupter (GFCI) or Earth- Leakage Circuit-Breaker
(ELCB).
ORDERING INFORMATION
VEIL Intelligent Toilet
Includes Remote Controller Assy
NOTES
DANGER: Risk of electric shock. Disconnect power before using.
WARNING: Risk of electric shock. Connect only to circuits protected by Ground-Fault
Circuit-Interrupters (GFCI's) or Earth-Leakage Circuit-Breakers (ELCB's).
a rag in the floor flange opening.
NOTICE: Follow all local plumbing and electrical codes.
NOTICE: Receptacles installed in bathrooms to be located at least 1 meter from a bathtub or shower if
practical.
CAUTION: Risk of hazardous gases. If a new toilet is not installed immediately, temporarily place
yltsrif,deneposievlavllabehtretfA.ecivedgni
tsetyticapacylppusretawdetacidedesutsum:noitnettA
flush three times and test.
The minimum dynamic pressure for the testing device is advised to be above 0.046Mpa(6.7 psi).
Pressure gau
Ball valve
Ho
Product inlet Hose se
Product tee valve
ge
Kohler Co.
3
1243902-KR01-D

Water
Measurements
Remote control Unit: mm
Waterproof socket (grounding type)
Inlet hose
Fig.#3
Kohler reserves the right to change marked dimensions without prior notice.
SPECIFICATIONS
NOTE: See "Homeowner's Guide" for detailed specifications of the bidet seat.
*Power value testing condition: dynamic pressure 0.2Mpa, inlet water temp 15°C.
1243902-KR01-D
4
Kohler Co.
Average 3.6L, Full flush 4.8L, Flush ECO 3.0L
305mm
Min water pressure 0.1Mpa (dynamic pressure)
Max water pressure 0.74Mpa
220V-240V~, 50/60Hz
1000W
About 1.3m
About 670mm x 438mm x 533mm
About 46kg
35
40
Water supply volume
Pit distance
Water pressure
Rated voltage
Rated power*
Length of power line
Product outline dimension
Weight of product
Inlet water temp
Operation Environment

Fig.#4
Press the button for Flushing
× 4
세정 건조 전원
비데 물내림 조명
Fig.#5
Toilet
A. Hold the rim of the vitreous shell and take out the toilet.
WARNING: Risk of personal injury and product damage!Please do not hold the rim of the bidet seat when lifting the
the toilet. As the toilet is heavy, please seek help if necessary.
Overall Sketch
Crash pad
Seat (anti-microbial)
Seating sensing area
Nozzle
Press it again to turn it off.
Press Warm Wind button to start the warm wind function.
Press the button to enter Rear Wash mode.
Light sensing area
Press the button to enter Front Wash mode.
Press it again to turn it off.
Press the button to turn off the night light function (long tone hint)
Press the button to turn off the power (long tone hint)
Press it again to turn it off.
Press it again to turn on (short tone hint)
PREPARATIONS BEFORE INSTALLATION
Kohler Co.
5
1243902-KR01-D

Fig.#6
B. Roughing-In
DANGER: Risk of electric shock. Disconnect power before servicing.
NOTE: This product is designed to work with wall mounted electrical and water supplies as shown in the
mounting dimensions.
WARNING: Risk of electric shock. Connect only to circuits protected by Ground-Fault Circuit-Interrupters
(GFCI's) or Earth-Leakage Circuit-Breakers (ELCB's).
Keep bath and shower away from electrical parts (such as remote controller, receptacle,etc).
When the electrical supply is mounted on the wall, a GFCI or ELCB protected and water proof receptacle
is required.
Fig.#7
A.
INSTALLATION
To Remove Existing Toilet
Turn off the water supply. Flush the toilet, and use a sponge to remove the remaining water from the tank and
bowl. Disconnect the supply shut-off valve (if present), and remove the old tank and bowl.
B. Place an 800mmX800mm cushion on the floor, take out the toilet from the carton then put the
toilet on it.
Remove old gasket from the floor and closet flange with a putty knife. Remove old T-bolts and discard them.
NOTICE: if a new toilet is not installed immediately, temporarily stuff a rag in the closet floor flange.
Closet Floor Flange
1243902-KR01-D
6
Kohler Co.

Unit: mm
Fig.#8
250 10 250 10
200 5
85 5
305
01051
01051
Fig.#10
Bolt
C. 1.Confirm the drain hole center and mark down the“+”centerline
perpendicular to the finished wall.
2.Confirm the toilet drain hole center and mark down the centerline on
Front , back , left and right outside of toilet.
3.
Make sure the toilet side mark symbol is align to the drain hole
centerline on the finished floor.Mark down the left and right holes.
Fig.#9
Hole(two sides)
Mark symbol
305mm
3/8
10mm
D. Drill two holes and insert two anches and bolts.
Kohler Co.
7
1243902-KR01-D

E.
Silica gel
Fig.#1
Coated Silica gel on the opposite
side of floor flange
Position the floor flange align the
drain hole, and press it onto the
finished floor .
Install the Electrical Service and Water Supply.
DANGER: Risk of electric shock. Disconnect power before servicing.
DANGER: Risk of electrical shock. For plug-in installations/wall-mounted electrical supply: connect only to a
properly-grounded, grounding-type receptacle protected by a Ground-Fault Circuit-Interrupter
(GFCI). Do not remove the grounding pin or use a grounding adapter.
DANGER: Risk of electrical shock. For hardwire installations/through-floor electrical supply:
Connect only to a properly-grounded, dedicated 220V-240V~, 10A, 50Hz/60Hz circuit protected by a Class
A Ground-Fault Circuit-Interrupter (GFCI) or Earth-eakage Circuit-Breaker (ELCB).
NOTE: This product is designed for installation with the electrical supply attached to the wall. Both types
are illustrated. Refer to the dimensional information for your chosen installation.
Follow the dimensional information exactly when installing the hardwire electrical supply.
Side Plate Nut cap
Fig.#1
F. Install the Floor Flange
G. Remove side plates
Unscrew the nut cap on the tee joint.
1243902-KR01-D
8
Kohler Co.

Nut
Fig.#14
WARNING: Risk of personal injury. The vitreous shell weighs 35 kg. Use proper lifting technique when
handling the vitreous shell.
CAUTION: Risk of product damage. Do not set the shell down hard. Gently lift and move the shell if it is not
placed correctly. If handled harshly, the shell may chip or break.
Carefully pick up the vitreous shell.
Make sure the trap way sits fully in the outlet gasket. If the vitreous shell does not sit evenly on the floor, then the
trap way will not be properly aligned.
Make all adjustments gently reference the toilet side mark symbol and the drain hole centerline on the finished
floor until the trapway is properly seated.
Use nut and washer to fasten the bolts and fix up the toilet.
CAUTION: Risk of product damage . Do not move the toilet after the trap way is properly seated to
avoid the wax seal invalidated, Change the wax ring if it is needed to move.
WARNING: Risk of personal injury or product damage. Overtightening may cause breakage or chipping.
Fig.#1
H. Fix Wax Ring
Place the wax ring on the waste outlet.
I. Install the Vitreous Shell
Kohler Co.
9
1243902-KR01-D

Fig.#16
Fig.#15
150 10
250 10
Close by rotating the handle clockwise and
open counterclockwise
Handle of tee valve
Tee valve
Decorative cover
J.
2.
Install Tee Valve.
IMPORTANT!
1. Dimensions in the pictures are for reference only.
Install Deco Cover.
Unit: mm
1. Connect the water outlet.
2. Open the shut-off valve.
NOTE: Please do not reuse the old hose.
K. Connect the Water
IMPORTANT!The supplied hose must be used for this installation.
1243902-KR01-D
10
Kohler Co.