Kohler WELLCOMME K-4349T User manual

ORDERING INFORMATION
Wellcomme Rear Spud Toilet ......................................K-4349T
Includes Seat.........................................................K-4670T
Includes Bowl ........................................................K-4349T
Wellcomme Top Spud Toilet ........................................K-4350T
Includes Seat.........................................................K-4670T
Includes Bowl ........................................................K-4350T
Highcliff Rear Spud Toilet ............................................K-4367T
Includes Seat.........................................................K-4670T
Includes Bowl ........................................................K-4367T
Highcliff Top Spud Toilet ..............................................K-4368T
Includes Seat.........................................................K-4670T
Includes Bowl ........................................................K-4368T
Service Parts
38mm closet spud assy.............................................18357
Bolt Cap Accessory Pack ...................................1013092-0
Please read these instructions carefully to familiarize yourself
with the required tools, materials, and installation sequences.
Follow the sections that pertain to your particular installation .
This will help you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.
All information in these instructions is based upon the latest
product information available at the time of publication. Kohler
China reserves the right to make changes in product
characteristics, packaging, or availability at any time without
notice.
These instructions contain important care, cleaning, and
warranty information-please leave instructions for the
consumer.
........................................................K-4349T
................................................................K-4670T
................................................................K-4349T
........................................................K-4350T
................................................................K-4670T
................................................................K-4350T
................................................K-4367T
................................................................K-4670T
................................................................K-4367T
................................................K-4368T
................................................................K-4670T
................................................................K-4368T
38mm ..........................................................18357
......................................................1013092-0
-
NOTES
·
·
·
·
·
·
·
Observe all local plumbing and building codes.
Shut off the water supply.
57mm (2") passageway.
Ensure that the new drain has the correct roughing-in
dimension. This toilet has a 305mm (12") roughing-in
dimension.
Be very careful while working with vitreous china products.
Vitreous china can break or chip if the bolts and nuts are
overtightened, or if carelessly handled.
Carefully inspect the new fixture for any sign of damage.
For new construction, refer to the dimensions in
and for locating the shut-off valve.
Fixture dimensions are nominal and conform to tolerances
established by ANSI Standards (A112.19.2M).
The fill valve
nut has been factory-tightened to design specifications.
If re-tightening is required, wrench tighten 1/4 turn past
finger tight.
See Fig. #1.
Fig. #1
Fig. #4
WARNING: Risk of external leakage.
·
·
·
·
·
·
·
·
·
57mm
254mm 305mm 279mm( 1)
(ANSI)
A112.19.2M
1007282-2-A -1-
HIGHCLIFF
WELLCOMME
TM
TM
INSTALLATION INSTRUCTINS
VITREOUS CHINA COMMERCIAL TOILETS
S-EB 305mm K-4349T/K-4350T S-EB 305mm K-4367T/K-4368T

TOOLS AND MATERIALS REQUIRED
(Not supplied)
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
254mm (10") adjustable wrench
305mm (12") pipe wrench
Metal file (file cut)
Tape measure
Tubing cutter
Level
Hacksaw
Putty knife
Screwdriver
Sponge
Safety Glasses
Toilet gasket (wax seal)
Toilet installation flange
Toilet T-bolts (2), 8mm (5/16") diameter
Toilet supply shut-off valve, 10mm (3/8") recommended
If the existing toilet does not have a supply shut-off
valve below the tank, install one before installing the new
toilet.
* Flexible hose are recommended to connect the supply line
to the fill valve. If you use a rigid connection, take care not to
apply side forces to the bottom of the fill valve.
NOTICE:
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
254mm
305mm
()
8mm T (2 )
10mm
*
-2-
Unit: mm
Fig.#1
1
INSTALLATION
TO REMOVE EXISTING TOILET
Turn off the water supply. Flush the toilet, and use a sponge
to remove the remaining water from the tank and bowl.
Disconnect the supply shut-off valve (if present), and remove
the old tank and bowl.
()
1007282-2-A
K-4349T
K-4350T
K-4368T
38 SPUD 368
241
375
727
330 67
279 MIN.
143
MIN.
MIN.
OF OUTLET
C
L
375
K-4367T
38 SPUD
368
445
727
279 MIN.
MIN.
OF OUTLET
C
L
400
OF OUTLET
C
L
57
51
162
375
375
143 241
368
38 SPUD
MIN.
702 752
254 305
57
70 38 SPUD 368
445
171
143 375 241
MIN.
702 752
OF OUTLET
C
L
254 305
67
MIN.

Remove the old gasket from the floor
and closet flange with a putty knife.
Remove the old T-bolts and discard
them.
If the new toilet is not
installed immediately, temporarily stuff
a rag into the closet flange.
NOTICE:
T
Closet Flange Fig.#2
2
-3-
1007282-2-A
Assemble the bolt cap bases, washer,
and nuts on exposed T-bolts. Hand
tighten the nuts, then tighten them an
additional 1/2-turn.
Overtightening may cause
breakage or chipping of the
vitreous china.
If the T-bolts extend more than 6mm
(1/4") over the top of the nuts, cut off
the excess and file the end. Wipe
away any residue. Install the bolt cap.
CAUTION: Risk of personal
injury or product damage:
T
T 6mm
Fig.#6
6
8mm TInstall two new 8mm (5/16") diameter
T-bolts into the closet flange.
Do not use white cement or
high lime content cements to install
this toilet. The expansion of cement
due to a rise in temperature may make
the toilet crack or cause damage.
Kohler is not responsible for any
damage caused by installation with the
use of cement.
NOTICE:
TO INSTALL TOILET
K-4349 toilet shown throughout the
instructions.
Set the toilet upside down on some
padding. Firmly press the toilet gasket
onto the toilet outlet.
Wax ring type toilet gasket
should not be installed at temperatures
less than 21 .
If you are using a toilet
gasket with an integral plastic sleeve,
make sure the gasket is positioned
with the sleeve facing away from the
toilet.
If you temporarily plugged the closet
flange with a rag, remove the rag at
this time and ensure that the drain pipe
is clear and free of debris.
Carefully align and lower the toilet over
the closet flange and T-bolts. Apply full
body weight to the toilet rim to set the
seal.
Do not lift or rock the
toilet after placement-anew
toilet gasket must be installed if
you break the watertight seal.
NOTE 1:
NOTE 2:
CAUTION: Risk of external
leakage:
K-4349
1
21
2
Fig.#3
3
T-Bolts
TCloset Flange
Fig.#5
5
Bottom of Bowl
Toilet Gasket
Closet Flange
T-Bolt
T
Bolt Cap
Nut
Washer
Bolt Cap Base
T-Bolt
T

1007282-2-A -4-
INSTALL FLUSH VALVE
Refer to flush valve manufacturer's installation instructions for
rear spud or top spud connection.
START-UP
·
·
Turn on the water supply.
Flush and check bowl and flush valve connections for
leaks.
·
·
INSTALL SEAT
For bowls with seats, use seat attachment hardware and
instructions packed with toilet seat.
138 19
200021
Http://www.kohler.com.cn
LIMITED ONE-YEAR WARRANTY
Kohler plumbing fixtures are warranted free of manufacturing
defects.
Kohler will at its election, repair, replace, or make appropriate
adjustment where Kohler inspection discloses any such
defects occurring in normal usage within one year after
installation. Kohler is not responsible for installation costs.
To obtain warranty service, contact Kohler either through your
Dealer or Plumbing Contractor or by writing:
Central Customer Service Centre, Kohler China Ltd.,
19/F ShangHai Square, 138 Huai Hai Road,
LuWan District, ShangHai, China
200021, PRC
Http://www.kohler.com.cn
CONSUMER RESPONSIBILITIES
When cleaning up after installation, do not use abrasive
cleansers, as they may scratch and dull the toilet surface.
Use warm water and a liquid detergent to clean the surface.
Remove stubborn stains, paint, or tar with turpentine or paint
thinner. Do not allow cleaners containing petroleum distillates
to to remain in contact with any toilet surface for long periods
of time.
Remove plaster by carefully scraping with a wood edge. Do
not use metal scrapers, wire brushes, or other metal tools.
Use a powder type detergent on a damp cloth to provide mild
abrasive action to any residual plaster.
Clean the outside surface of your vitreous china product with
mild soap and warm water. Wipe the entire surface
completely dry with a clean, soft cloth.
Most toilet bowl cleaners are not harmful to the vitreous china
surface of the toilet bowl. Please follow the bowl cleaner
manufacturer is instructions carefully.
Do not use abrasive cleaners or solvents.
ã, 2002
Copyright Kohler China Ltd., 2002
C