Kohler OVE K-19950W User manual

OVE
INSTALLATION INSTRUCTIONS
VITREOUS CHINA WALL-HUNG LAVATORY
K-19950W/K-19951W
-1-
1062888-T01-A
106 2 324 200131
, 2006
Copyright Kohler China Ltd., 2006
·
·
·
Observe all local plumbing and building codes.
Prior to installation, unpack the new lavatory and inspect it
for damage. Return the lavatory to its protective carton
until you are ready to install it.
All information in these instructions are based the latest
product information available at the time of publication.
Kohler China reserves the right to make changes in
product characteristics, packaging, or availability at any
time without notice.
Make sure that the wall and floor are square
and plumb to ensure proper installation.
IMPORTANT:
·
·
·
ORDERING INFORMATION
OVE Vanity Top.................................................K-19950W
Includes Mounting Kits .....................................1034692
OVE Vanity Top.................................................K-19951W
Includes Mounting Kits .....................................1034692
........................................................K-19950W
........................................................1034692
........................................................K-19951W
........................................................1034692
REQUIRED MATERIALS/
(NOT SUPPLIED)
TOOLS
·
·
·
·
·
Level
Drill with bit6mm
14mm wrench
Framing square
Channel lock pliers
Tape measure
·
·
·
·
·
·
·
6mm
14mm

ROUGHING-IN DIMENSIONS
ROUGHING-IN DIMENSIONS
UNIT: mm
:
Fig.#1
1
K-19951W
140
855
670
865
820
220
70
35
470
45
950
605
130
515
350
45
440
1205
440
150
K-19950W
150 140
855
670
860
815
220
280
35
130
515
350
440
905
45
70
470
Install the Basin
Note! The vanity tops can be installed on a cabinet or
matching metal stand (refer to Installation and User Guide
packed with the cabinet or stand for installation details).
Recommend Kohler metal square leg or Kohler bathroom
furniture for support or decoration.
!
!(
)
!
1.
2.
3.
4.
5.
1. Install the services.
2. Make sure that the hot and cold water supply pipes and the
waste are installed correctly.
3. Mark the position on the wall for the attachment bolts.
Make sure that you avoid hidden cables and
pipes when drilling holes in the wall.
4. Drill the fixing holes.
5. Fit the wall plugs and attachment bolts.
Caution!
-2-
1062888-T01-A

Fig.#2
2
-3-
280mm
Attachment
Bolt (x2)
Wall Plug
550mm
Waste
Outlet Waste
630mm
815mm
80mm
Single Vanity Top
Fig.#3
3
Double Vanity Top
950mm
Attachment
Bolt (x2)
Wall Plug
550mm
Waste
Outlet Waste
630mm
820mm
80mm
6.
Note! The hot and cold water supplies must terminate with a
supply shut off valve.
6. Fit the tap to the basin in accordance with the
manufacturer s instructions.
,
1062888-T01-A

7. Apply silicone sealant to the back of
the basin.
8. Fit the basin in position over the
attachment bolts.
9. Adjust the offset nut until the basin
is level.
10. When the basin is level, fit the
washers and the nuts to secure in
place.
11. Remove any excess silicone
sealant.
7.
8.
9.
10.
11.
Apply Silicone sealant
along this face
Washer Nut
Offset Nut
Fig.#4
4
-4-
Overflow
Cover
12.12. Place the overflow cover over the overflow hole in the
basin, making sure it is orientated correctly.
Fig.#5
5
1.
2.
3.
4.
Install the Plumbing
1. Install the drain in accordance with the manufacturer s
instructions.
Make sure a watertight seal exists on all
basin drain connections.
Provide access to the plumbing connections
for future plumbing maintenance.
2. Connect the hot and cold water supplies.
3. Open the hot and cold water valves, and check the supply
connections for leaks.
4. Run water into the basin, and check the drain connections
for leaks.
Caution!
Caution!
,
Fig.#7
7
1062888-T01-A

IMPORTANT CONSUMER INFORMATION
IMPORTANT CONSUMER INFORMATION
CARE AND CLEANING
To keep your lavatory looking new, make sure you rinse it out
thoroughly after each use. on this
product, as they will scratch and ruin the surface. Stubborn
stains, paint, or tar can be removed with turpentine or paint
thinner.
DO NOT USE ABRASIVES
Caution! Risk of product damage.
Many cleaners contain abrasive and chemical substances,
and should not be used for cleaning stainless steel, enamel,
plated or plastic fittings.
These finishes should be cleaned using a mild washing up
detergent or soap solution, rinsed and then wiped dry with a
soft clean cloth.
-5-
LIMITED ONE-YEAR WARRANTY
LIMITED ONE-YEAR WARRANTY
()
()
138
19
200021
Plumbing Fixtures and Fittings Limited
One-year Warranty
Kohler plumbing fixtures and fittings are warranted to be free
of manufacturing defects.
This product is warranted for one year from date of purchase.
Kohler China will be responsible for any problems caused by
manufacturing defects provided with the invoice. Kohler
China will, at its election, repair, replace or make appropriate
adjustment where Kohler China inspection discloses any
such defects occurring in normal usage within one year after
purchase.
Implied warranties including that of merchantability and
fitness for a particular purpose are expressly limited in
duration to the duration of this warranty, Kohler China
disclaims any liability for special, incidental or consequential
damages. Damages to the product caused by misuse, abuse
and installation that is not in accordance with the owner's
manual are not covered by this warranty.
To obtain quick warranty service, please contact your dealer,
or write to Kohler China. (Original sales receipt must be
provided as the proof of purchase.)
Kohler China Investment Company Ltd.
Central Customer Service Center
19/F, Shanghai Square, 138 Huai Hai Road,
Luwan District, Shanghai, PRC
Zip Code: 200021
This is our exclusive written warranty.
1062888-T01-A