Konica Minolta ViZion DR + User manual

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
1
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
ViZion DR +
Wireless Install Guide
1. Open the DR panel box.
2. Put aside the three cables from the top layer of Styrofoam for storage. These cables are only required
for potential troubleshooting scenarios.
3. The panel is shipped in an antistatic bag. Remove the bag from the box.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
2
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
4. Remove the panel from the antistatic bag.
5. Remove the battery charger from the box. Under the battery charger are two (2) external power
supplies. One (1) is to be used for the battery charger, and the other can be stored.
6. Remove the two (2) batteries from the box and place both in the charger. Batteries should be
charged prior to use.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
3
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
7. After batteries are charged, insert battery into panel. Turn panel over with battery compartment facingup.
a. Slide battery into the Panel at a slight angle mating the charging connector with the battery
connector. While sliding the battery, check alignment of the charging connector with the
battery connector.
b. Let battery fall into place, then slide the two (2) locking latches to secure the battery in thepanel.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
4
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
9. Locate the power buttons on the edge of the panel.
a. Press and hold the power button for up to 10 seconds or until the lights turn on.
A. Battery status (green - battery is charged, orange – replace battery soon)
B. Link status (green connected via Ethernet blue – connected via wifi)
C. Communication (solid green / flashing green is communication between software andpanel.)
D. Power button
E. Infrared port for future expansion.
A B C D E

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
5
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
AP Setup
1. Unbox Asus Access point (model may vary based on availability).
1A 1B ------------- 2 ------------- 1C 3 4 5 1D
1A-1D: Wifi Antennas
2: Gigabit Lan Ports
3: Reset Button (Restores Access Point to Factory
Defaults) 4: Power Button
5: AC adapter Plug
2. Attach antennas to Access point.
3. Place Access point in X-ray room close to area where exams are completed and close to a power source.
4. Plug Access point into power source and power on Access point.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
6
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
6. Access point is configured from the factory with the following settings:
a. 2.4ghz radio – Disabled
b. 5 GHz radio - Enabled
c. IP address 192.168.8.50 for the router
d. username: admin (default username: admin)
e. password: 12345678 (default password: admin)
f. SSID : ViZionDREXAP password : 12345678
Note: DHCP is disabled and the AP will not assign addresses to network devices.
Monitor Setup
1. Unbox Monitor (Note: For ELO touch screen Monitors base comes mounted onto LCD screen).

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
7
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
2. Attach platform to base.
3. Attach Base to Monitor.
4. Cover wall mount screws with provided cover.
5. Insert power cable into monitor and plug power cable into wall outlet.
6. Insert blue VGA cable into monitor VGA port. (May arriveconnected)
NOTE:
For ELO touch screen monitors a USB cable and Serial cable will be included in the box. Attach the USB cable to
the monitor.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
8
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
Back of ELO Monitor
1 2 3
1: AC Power cable
2: USB cable (A to B standard)
3: VGA Cable

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
9
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
PC Setup
1. Open PC Box.
2. Remove Key Board and Accessories box.
3. Remove PC and place PC in X-ray work area.
4. Plug Keyboard into PC USB port.
5. Plug Mouse into PC USB port.
6. Connect On Board Lan port to
site Local Area internet network
(wall network port).
7. Connect riser network card to
LAN port on wireless access
point (yellow ports on ASUS
wireless AP).
8. Connect monitor to VGA port on PC.
9. Plug power cable into PC and plug
power cable into wall outlet.
10. Power on Monitor.
11. Power on PC.
Reference Quick
wiring guide on next
page.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
10
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
PC Wiring guide made simple
Connect the onboard
network card to the office’s
local area network.
Connect the mouse and
Keyboard
to any available USB port.
Connect the
monitor to
the PC VGA
port
Note for ELO Monitors attach
the USB cable to an open
USB port on the PC
Connect a network cable from port
label 1 to the add-on network
card on the PC.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
11
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
ELO Touchscreen software install andCalibration
1. Click the desktop icon.
2. At the first prompt, click OK.
3. At the next prompt, click Unzip.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
12
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
4. At the next prompt, cick OK.
5. At the Touch Screen setup, click Next.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
13
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
6. Check the box next to “Install USB Touchscreen Drivers.”
7. At the next prompt, click Yes.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
14
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
8. When prompted, click Finish.
9. Plug the USB cable into the back of the pc.
Wait for one minute for windows to complete driverinstallation.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
15
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
10. Click the ELO icon in the system tray.
11. Click the Align option.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
16
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
12. Touch the bull’s eye symbol on thescreen.
13. Touch each bull’s eye as they display on thescreen.

ViZion DR + Install Guide v2.6
Opal UAI 2.3.x.x
17
Customer Support 1.800.366.5343 – [e-mail]
VZ0001HTG201507-2.6
14. Touch different areas on the screen. If the mouse follows the spots you touch, then touch the green
check symbol on the screen.
Installation of the ELO touch screen monitor iscomplete.