Kontron 3.5"-SBC-WLU User manual

Kontron 3.5"-SBC-WLU - Quick Installation Guide - Version 2 - P/N: 0D20ECXWLU020000 // 1

3.5"
-SBC-WLU - QUICK INSTALLATION GUIDE
Thank you for purchasing the Kontron 3.5"-SBC-WLU embedded board. This document provides information to allow you
to quickly install this product.
Packing Checklist
1. Take the 3.5"-SBC-WLU out of the packing box and check if the unit is properly secure in the plastic bag.
2. Check the contents of the carton box: (*: optional)
3.5"-SBC-WLU main board
Quick Installation Guide
DC IN Cable
COM Port Cable *
DIO Cable *
USB Cable (2 Port) *
SATA Cable *
SATA Power Cable *
Audio Cable *
Cooler *

Kontron 3.5"-SBC-WLU - Quick Installation Guide - Version 2 - P/N: 0D20ECXWLU020000 // 2
Top Side Jumper and Internal Connector Locations
Jumper List
Item Designation Description
1 JP1 LVDS Panel Power Selection
2 JP2 LVDS Backlight Control Selection
3 JP3 LVDS Backlight Enable Selection
4 JP4 Integrated CNVi Selection for M2E1
5 JP5 Flash Descriptor Security Override Selection
6 JP6 AT / ATX Power Mode Selection
7 JP7 Clear CMOS Selection
8 JP9 USB Power Selection
9 JP10 MFG Mode Selection
20
19
22
23
24
1
2
3
4
14
15
16
5
30
18
21
8
9
10
11
12
13
25
26
27
28
29
17
7
6

Kontron 3.5"-SBC-WLU - Quick Installation Guide - Version 2 - P/N: 0D20ECXWLU020000 // 3
Internal Connector List
Item Designation Description
10 BAT1 RTC Power Input Wafer
11 CN1 Activity Indicator Header for M2B1
12 CN2 SDXC / DIO Header
13 CN3 FAN Wafer
14 CN4 Activity Indicator Header for M2E1
15 CN5 +12 V DC Power Input Wafer
16 CN8 +5 V DC HDD / SSD Power Output Wafer
17 CN9 Micro SIM Card Holder for M2B1
18 CN10 Audio Input / Output Header
19 CN11 Right Channel Audio AMP Output Wafer
20 CN16 USB 2.0 Port 6, 7 Header
21 CN17 USB 2.0 Port 8, 9 Header
22 CN20 Left Channel Audio AMP Output Wafer
23 DIMM1 DDR4 Channel 0 SO-DIMM Slot
24 DIMM2 DDR4 Channel 1 SO-DIMM Slot
25 FP1 Front Panel Header 1
26 FP2 Front Panel Header 2
27 M2B1 M.2 Key B 3042 Slot
28 M2E1 M.2 Key E 2230 Slot
29 M2M1 M.2 Key M 2242 / 2280 Slot
30 SATA1 SATA Port 0 Connector
Jumper Setting
LVDS Panel Power Selection (JP1)
Jumper 1 Position Description
Pin 1-3 Pin 3-5
X - Backlight Power = +12 V
- X Backlight Power = +5 V
Jumper 2 Position Description
Pin 2-4 Pin 4-6
X - Panel Power = +3.3 V
- X Panel Power = +5 V
“X” = Jumper set (short) and “-” = jumper not set (open)
21
65

Kontron 3.5"-SBC-WLU - Quick Installation Guide - Version 2 - P/N: 0D20ECXWLU020000 // 4
LVDS Backlight Control Selection (JP2)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - PWM Control Mode
- X Voltage Control Mode
“X” = Jumper set (short) and “-” = jumper not set (open)
LVDS Backlight Enable Selection (JP3)
Jumper 1 Position Description
Pin 1-3 Pin 3-5
X - Backlight Enable Level = +3.3 V
- X Backlight Enable Level = +5 V
Jumper 2 Position Description
Pin 2-4 Pin 4-6
X - Backlight Enable High Active
- X Backlight Enable Low Active
“X” = Jumper set (short) and “-” = jumper not set (open)
Integrated CNVi Selection for M2E1 (JP4)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - Integrated CNVi Disabled
- X Integrated CNVi Enabled
“X” = Jumper set (short) and “-” = jumper not set (open)
2
3
1
21
65
2
3
1

Kontron 3.5"-SBC-WLU - Quick Installation Guide - Version 2 - P/N: 0D20ECXWLU020000 // 5
Flash Descriptor Security Override Selection (JP5)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - Normal Operation
- X Flash Security Override
“X” = Jumper set (short) and “-” = jumper not set (open)
AT / ATX Power Mode Selection (JP6)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - ATX Mode
- X AT Mode
“X” = Jumper set (short) and “-” = jumper not set (open)
Clear CMOS Selection (JP7)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - Normal Operation (default position)
- X Clear CMOS (board does not boot with the jumper in this position)
“X” = Jumper set (short) and “-” = jumper not set (open)
2
3
1
2
3
1
2
3
1

Kontron 3.5"-SBC-WLU - Quick Installation Guide - Version 2 - P/N: 0D20ECXWLU020000 // 6
USB Power Selection (JP9)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - +5 V
- X +5 VSB
“X” = Jumper set (short) and “-” = jumper not set (open)
MFG Mode Selection (JP10)
Jumper 1 Position Description
Pin 1-2 Pin 2-3
X - Normal Operation
- X Enable MFG Mode
“X” = Jumper set (short) and “-” = jumper not set (open)
2
3
1
2
3
1

Kontron 3.5"-SBC-WLU - Quick Installation Guide - Version 2 - P/N: 0D20ECXWLU020000 // 7
Bottom Side Internal Connector Locations
Item Designation Description
1 CN21 LVDS Backlight Power Wafer
2 CN22 RS232/422/485 COM2 Wafer
3 CN23 RS232/422/485 COM1 Wafer
4 CN24 24-bit / 2-ch LVDS Connector
1
4
2
3

Kontron 3.5"-SBC-WLU - Quick Installation Guide - Version 2 - P/N: 0D20ECXWLU020000 // 8
Rear I/O Panel Connector Locations
Item Designation Description
1 CN12 GbE LAN1 RJ45 Connector
2 CN13 GbE LAN2 RJ45 Connector
3 CN14 USB 3.1 Port 1, 2 Type A Connector
4 CN15 USB 3.1 Port 3, 4 Type A Connector
5 CN18 DP++ Port 2 Connector
6 CN19 DP++ Port 1 Connector
1
2
3
4
5
6