Kontron 3.5-SBC-KBL User manual

Kontron 3.5"-SBC-KBL/SKL - Quick Installation Guide - Version 2 - P/N: 0D20ECXSLU020100 // 1

3.5"
-SBC-KBL/SKL - QUICK INSTALLATION GUIDE
Thank you for purchasing the Kontron 3.5"-SBC-KBL/SKL embedded board. This document provides information to allow
you to quickly install this product.
Packing Checklist
1. Take the 3.5"-SBC-KBL/SKL out of the packing box and check if the unit is properly secure in the plastic bag.
2. Check the contents of the carton box: (*: optional)
3.5"-SBC-KBL/SKL embedded board
Quick Installation Guide
1x DC Jack Cable
1x SATA Cable*
1x SATA Power Cable*
COM Port Cable*
DIO Cable*
2-Port USB Cable*
Audio Cable*
Mini SIM Card Holder Kit*
Heatsink* (for 15 W TDP CPU)

Kontron 3.5"-SBC-KBL/SKL - Quick Installation Guide - Version 2 - P/N: 0D20ECXSLU020100 // 2
Top Side Jumper and Internal Connector Locations
Jumper List
Item Designation Description
1 JP1 MPCIE1 Activity LED Pin Header
2 JP2 Panel & Backlight Power Selection for LVDS1
3 JP3 NGFF M.2 Activity LED Pin Header
4 JP4 Backlight Power Enable Selection for LVDS1
5 JP6 AT / ATX Power Mode and NGFF mSATA/mPCIe Selection
6 JP7 SIM Card and USB Power Selection
7 JP8 Flash Descriptor Security Override Selection
8 JP9 RTC Reset Selection
9 JP10 Clear ME Register
Internal Connector List
Item Designation Description
10 BAT1 RTC Power Input Wafer
11 FAN1 +12VDC CPU FAN Wafer
12 DIMM1 Primary DDR4 Memory SO-DIMM Socket
1
3
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

Kontron 3.5"-SBC-KBL/SKL - Quick Installation Guide - Version 2 - P/N: 0D20ECXSLU020100 // 3
Item Designation Description
13 DIMM2 Secondary DDR4 Memory SO-DIMM Socket
14 MPCIE1 Full Size Mini-PCI Express v1.2 Socket
15 CON1 NGFF M.2 Key-B Socket
16 SATA1 Serial ATA Port-0 SATA Socket
17 SATA2 Serial ATA Port-0 SATA Socket
18 CN1 HDD Power Output Wafer
19 CN2 DC12V Power Input Wafer
20 CN3 P80 Header
21 CN4 SIM Interface Wafer for MPCIE1/NGFF M.2
22 CN5 Digital Input / Output Wafer
23 CN6 Serial Port 1 Wafer
24 CN7 Serial Port 2 Wafer
25 CN8 USB 2.0 Port DN5,6 Pin Header
26 CN9 Audio Input / Output Pin Header
27 CN10 Left Channel 3W Audio AMP Output Wafer
28 CN15 Right Channel 3W Audio AMP Output Wafer
29 FP1 Front Panel 1 Pin Header
30 FP2 Front Panel 2 Pin Header
Jumper Settings
MPCIE1 Activity LED Pin Header (JP1)
Jumper Position Description
1 LED+
2 LED-
1
2

Kontron 3.5"-SBC-KBL/SKL - Quick Installation Guide - Version 2 - P/N: 0D20ECXSLU020100 // 4
Panel & Backlight Power Selection for LVDS1 (JP2)
Jumper 1 Position Description
Pin 1-3 Pin 3-5
X - Backlight Power = +12V
- X Backlight Power = +5V
Jumper 2 Position Description
Pin 2-4 Pin 4-6
X - Panel Power = +3,3V
- X Panel Power = +5V
“X” = Jumper set (short) and “-” = jumper not set (open)
NGFF M.2 Activity LED Pin Header (JP3)
Jumper Position Description
1 LED+
2 LED-
Backlight Power Enable Selection for LVDS1 (JP4)
Jumper 1 Position Description
Pin 1-3 Pin 3-5
X - Backlight Enable Voltage = +3.3V
- X Backlight Enable Voltage = +5V
Jumper 2 Position Description
Pin 2-4 Pin 4-6
X - Active High
- X Active Low
“X” = Jumper set (short) and “-” = jumper not set (open)
2
1
65
1
2
21
65

Kontron 3.5"-SBC-KBL/SKL - Quick Installation Guide - Version 2 - P/N: 0D20ECXSLU020100 // 5
AT / ATX Power Mode & NGFF mSATA / mPCIe Selection (JP6)
Jumper 1 Position Description
Pin 1-3 Pin 3-5
X - ATX Mode
- X AT Mode
Jumper 2 Position Description
Pin 2-4 Pin 4-6
X - NGFF Select mSATA
- X NGFF Select mPCIe
“X” = Jumper set (short) and “-” = jumper not set (open)
SIM Card and USB Power Selection (JP7)
Jumper 1 Position Description
Pin 1-3 Pin 3-5
X - SIM Card to NGFF
- X SIM Card to mPCIe
Jumper 2 Position Description
Pin 2-4 Pin 4-6
X - S5 USB Power Support
- X S3 USB Power Support
“X” = Jumper set (short) and “-” = jumper not set (open)
Flash Descriptor Security Override Selection (JP8)
21
65
21
65

Kontron 3.5"-SBC-KBL/SKL - Quick Installation Guide - Version 2 - P/N: 0D20ECXSLU020100 // 6
Jumper Position Description
Pin 1-2
X Enable
- Disabled
“X” = Jumper set (short) and “-” = jumper not set (open)
RTC Reset Selection (JP9)
Jumper Position Description
Pin 1-2
X Enable Clear CMOS RTC content
(board does not boot with the jumper in this position)
- Disabled (default position)
“X” = Jumper set (short) and “-” = jumper not set (open)
Clear ME Register (JP10)
Jumper Position Description
Pin 1-2
X Enable Clear ME
- Disabled
“X” = Jumper set (short) and “-” = jumper not set (open)

Kontron 3.5"-SBC-KBL/SKL - Quick Installation Guide - Version 2 - P/N: 0D20ECXSLU020100 // 7
Bottom Side Internal Connector Locations
Item Designation Description
1 CN16 LCD Panel Power Connector
2 LVDS1 LVDS Panel Connector
Real I/O Panel Connector Locations
Item Designation Description
1 HDMI1 HDMI Port-1 Connector
2 DP1 DisplayPort Port-1 Connector
3 CN12 GbE LAN1 RJ-45 Connector
4 CN11 GbE LAN2 RJ-45 Connector
5 CN13 USB3.0 Port-1,2 Type-A Connector
6 CN14 USB3.0 Port-3,4 Type-A Connector
1
2
1
2
3
4
5
6