Kontron ECX-APL0 Series User manual

1
ECX-APL0 Series
Quick Installation Guide
Thank you for purchasing the Kontron ECX-APL0 Series embedded board. This document provides
information to allow you to quickly install this product.
Packing Checklist
1. Take the ECX-APL0 Series embedded board out of the packing box and check if the unit is properly secure in the
plastic bag.
2. Check the contents of the carton box: ( * : optional )
ECX-APL0 Series embedded board
1x SATA Cable*
Quick Installation Guide
1x SATA Power Cable*

Driver/ Manual CD

1x DC Jack Cable*
Jumper and Connector Locations

2
Jumper Settings
Before applying the power to ECX-APL0 Series embedded board, please make sure all jumper
settings are defaulted as the following table:
Jumper List
Label
Function
JP1
SIM CARD SELECTION
JP2
Backlight Enable Selection
JP3
Panel & Backlight Power Selection
JP4
AT / ATX Power Mode Selection
JP5
M2 KEY B LED Pin Header
JP6
MPCIE Activity LED Pin Header
JP8
RTC Reset Selection
JP9
USB Power Selection
JP10
ME F/W Selection
JP1 SIM CARD SELECTION
1
2
Jumper
Status
1-2 Open
M.2 KEY-B
1-2 Short
MPCIE (Default)
DIP 2P 1R MALE Pitch:2.54mm [Pinrex 210-91-02GB01]
JP2 Backlight Enable Selection
2
1
65
Jumper
Setting
Status
1
1-3
Backlight Enable Level = +3.3V
3-5
Backlight Enable Level = +5V
2
2-4
Backlight Enable High Active
4-6
Backlight Enable Low Active
SMD 6P 2R MALE TYPE 180D P-2.0mm[PINREX 222-97-03GBB1]
JP3 Panel & Backlight Power Selection
21
65
Jumper
Setting
Status
1
1-3
Backlight Power = +12V
3-5
Backlight Power = +5V
2
2-4
Panel Power = +3.3V
4-6
Panel Power = +5V
SMD 6P 2R MALE TYPE 180D P-2.0mm[PINREX 222-97-03GBB1]
JP4 AT / ATX Power Mode Selection
2
3
1
Jumper
Status
1-2 Short
ATX Mode
2-3 Short
AT Mode
DIP 3P 1R MALE STRAIGHT TYPE Pitch:2.54mm [PINREX 210-91-
03GB01]
JP5 M2 KEY B LED Pin Header
1
2
Pin
Descriptiom
1
LED+
2
LED-
DIP 2P 1R MALE Pitch:2.54mm [Pinrex 210-91-02GB01]

3
JP6 MPCIE Activity LED Pin Header
1
2
Pin
Descriptiom
1
LED+
2
LED-
DIP 2P 1R MALE Pitch:2.54mm [Pinrex 210-91-02GB01]
JP8 RTC Reset Selection
1
2
Jumper
Status
1-2 Open
Normal Operation.
1-2 Short
Clear CMOS
DIP 2P 1R MALE Pitch:2.54mm [Pinrex 210-91-02GB01]
JP9 USB Power Selection
1
2
Jumper
Status
1-2 Open USB power will be cut off in S4 & S5 state.
1-2 Short
USB power is always supply.
DIP 2P 1R MALE Pitch:2.54mm [Pinrex 210-91-02GB01]
JP10 ME F/W Selection
1
2
Jumper
Status
1-2 Open
Normal Operation
1-2 Short
ME F/W Disabled
DIP 2P 1R MALE Pitch:2.54mm [Pinrex 210-91-02GB01]
Internal Connector Pin Assignment
Label
Function
BAT1
CR2032 Battery Power Input Wafer
BZ1
Onboard Buzzer
CN1
DC12V Power Input Wafer
CN2
HDD Power Output Wafer
CN3
Micro-SD Card Cage
CN6
USB2.0 Port PORT4,5 Pin Header
CN7
SIM Interface Wafer for MPCIE1 and M2 KEY B
CN8
P80_Header
CN11
Audio Input / Output Pin Header
CN12
Left Channel 3W Audio AMP Output Wafer
CN14
Digital Input / Output Wafer
CN16
Right Channel 3W Audio AMP Output Wafer
CN17
COM1 RS-232/422/485 Port Wafer
CN18
COM2 RS-232/422/485 Port Wafer
CN19
RS-232 Port 5 Wafer
CN20
RS-232 Port 3 Wafer
CN21
RS-232 Port 4 Wafer
CN22
RS-232 Port 6 Wafer
CN23
Backlight Power Output Wafer
LVDS1
18/24-bit, 1/2-channel LVDS Panel Connector
DIMM1
DDR3L Memory SO-DIMM Socket
DIMM2
DDR3L Memory SO-DIMM Socket
FAN1
DC5V FAN Wafer
FP1
Front Panel 1 Pin Header
FP2
Front Panel 2 Pin Header
MPCIE1
Mini-PCI Express v1.2 Socket (Full Size)
CON1
M2 KEY B Socket
SATA1
Serial ATA Port 0 Connector
CN26
USB2.0 Port2 Pin Header (Option)

4
Rear Panel Pin Assignments
Label
Function
CN9
GbE LAN1 RJ-45 Connector
CN10
GbE LAN2 RJ-45 Connector
CN4
USB3.0 Port 1,2 Type-A Connector
CN5
USB3.0 Port 3,4 Type-A Connector
CN13
DP Connector
CN15
HDMI Connector
Customer Service
Kontron Asia Technology Inc.
5F, No. 415, Ti-Ding Blvd. Sec. 2 NeiHu District, Taipei 114, Taiwan
Tel：[phone] Fax：[phone]
ECX-APL0 Quick Installation Guide V2 (for KATW version) - P/N : 0D20ECXAPL020000