Kontron COMe Ref. Carrier-i T10 TNI Series User manual

The pulse of innovation
» User Guide «
COMe Ref. Carrier-i T10 TNIx
Doc. ID: 1060-3229, Rev. 1.2
Date: April 19, 2017

2
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNIx
Revision History
Imprint
Kontron Europe GmbH may be contacted via the following:
MAILING ADDRESS TELEPHONE AND E-MAIL
Kontron Europe GmbH +49 (0) 800-SALESKONTRON
Lise-Meitner-Str. 3-5 [email protected]
86156 Augsburg, Germany
For further information concerning other Kontron products, please visit our Internet website:
www.kontron.com.
Disclaimer
Copyright © 2016 Kontron AG. All rights reserved. All data is for information purposes only and not
guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate;
however, no responsibility is assumed for inaccuracies. Kontron and the Kontron logo and all other
trademarks or registered trademarks are the property of their respective owners and are recognized.
Specifications are subject to change without notice.
Revision Brief Description of Changes Date of Issue
1.0 Initial issue 01-Aug-2016
1.1 2.1.1 SPI Flash update
2.3.13 DIP Switch, update of table 15, position 7
23-Aug-2016
1.2 2.3.14 Power Supply and Management 19-Apr-2017

3
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNIx
Contents
Revision History ..........................................................................................................2
Imprint .....................................................................................................................2
Disclaimer ..................................................................................................................2
Contents ....................................................................................................................3
Tables .......................................................................................................................5
Figures ......................................................................................................................6
Warranty ....................................................................................................................7
Proprietary Note ..........................................................................................................7
Trademarks ................................................................................................................7
Environmental Protection Statement ................................................................................7
1 Introduction ....................................................................................... 8
1.1 Carrier Overview .......................................................................................... 8
1.2 Board Diagrams........................................................................................... 9
1.2.1 Functional Block Diagram .............................................................................. 9
1.2.2 Rear Panel ................................................................................................ 10
1.2.3 Board Layout ............................................................................................. 10
1.2.3.1 Component Overview ................................................................................... 12
1.3 Technical Specification ................................................................................ 13
1.4 Accessories ............................................................................................... 15
1.5 Standards ................................................................................................. 16
1.6 Related Publications.................................................................................... 17
2 Functional Description ......................................................................... 18
2.1 Memory .................................................................................................... 18
2.1.1 SPI Flash .................................................................................................. 18
2.1.2 Carrier EEPROM .......................................................................................... 18
2.2 Graphics Interfaces ..................................................................................... 18
2.2.1 Digital Display Interfaces ............................................................................. 18
2.2.2 LVDS/eDP Interface ..................................................................................... 19
2.3 System Interfaces ....................................................................................... 20
2.3.1 PCI Express Interfaces.................................................................................. 20
2.3.2 SATA Interfaces .......................................................................................... 20
2.3.3 Gigabit Ethernet Interfaces ........................................................................... 20
2.3.4 USB 2.0 Interfaces ...................................................................................... 21
2.3.5 USB 3.0 Interfaces ...................................................................................... 21
2.3.6 HD Audio Interfaces .................................................................................... 21
2.3.7 UART Interfaces.......................................................................................... 22
2.3.8 GPIO/SDIO Interfaces .................................................................................. 22
2.3.9 microSD/SIM Interface................................................................................. 23

4
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNIx
2.3.10 SYS_Signals / Embedded Interfaces ................................................................ 23
2.3.11 CPU Fan Interface ....................................................................................... 24
2.3.12 Front Panel Interface................................................................................... 24
2.3.13 DIP Switch ................................................................................................ 25
2.3.14 Power Supply and Management ...................................................................... 26
2.3.15 RTC.......................................................................................................... 26

5
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNIx
Tables
1 COMe Ref. Carrier-i T10 TNI Variants .........................................................................8
2 Component Overview .......................................................................................... 12
3 COMe Ref. Carrier-i T10 TNI Main Specifications ......................................................... 13
4 COMe Ref. Carrier-i T10 TNI Accessories ................................................................... 15
5 Standards ........................................................................................................ 16
6 Related Publications ........................................................................................... 17
7 LVDS/JILI Connector J15 Pinout ............................................................................ 19
8 Pinout of USB 2.0 Pin Header J10 .......................................................................... 21
9 S/PDIF Header J24 Pinout .................................................................................... 22
10 Pinout of Pin Header J8 ....................................................................................... 22
11 GPIO Pin Header J11 ........................................................................................... 22
12 Pin Header J6 ................................................................................................... 23
13 PWM Fan Connector J2 ........................................................................................ 24
14 Front Panel Connector J5 Pinout ............................................................................ 24
15 DIP Switch SW1 Functionality ................................................................................ 25
16 Power Connector J19 Pinout ................................................................................. 26
17 Smart Battery Connector J3 Pinout ........................................................................ 26

6
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNIx
Figures
1 COMe Ref. Carrier-i T10 TNI Functional Block Diagram ................................................. 9
2 COMe Ref. Carrier-i T10 TNI Rear Panel ................................................................... 10
3 COMe Ref. Carrier-i T10 TNI Layout - Top View .......................................................... 10
4 COMe Ref. Carrier-i T10 TNI Layout - Bottom View ..................................................... 11
5 LVDS/JILI Connector J15 .................................................................................... 19
6 USB 2.0 Pin Header J10 ...................................................................................... 21
7 S/PDIF Header J24 ............................................................................................ 22
8 Pin Header J8 .................................................................................................. 22
9 GPIO Pin Header J11 .......................................................................................... 22
10 Pin Header J6 .................................................................................................. 23
11 PWM Fan Connector J2 ....................................................................................... 24
12 Front Panel Connector J5 .................................................................................... 24
13 DIP Switch SW1 ................................................................................................ 25
14 Power Connector J19 ......................................................................................... 26
15 Smart Battery Connector J3 ................................................................................. 26

7
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNIx
Warranty
This Kontron product is warranted against defects in material and workmanship for the warranty period
from the date of shipment. During the warranty period, Kontron will at its discretion decide to repair
or replace defective products.
Within the warranty period, the repair of products is free of charge as long as warranty conditions are
observed.
The warranty does not apply to defects resulting from improper or inadequate maintenance or handling
by the buyer, unauthorized modification or misuse, operation outside of the product’s environmental
specifications or improper installation or maintenance.
Kontron will not be responsible for any defects or damages to other products not supplied by Kontron
that are caused by a faulty Kontron product.
Proprietary Note
This document contains information proprietary to Kontron. It may not be copied or transmitted by any
means, disclosed to others, or stored in any retrieval system or media without the prior written consent
of Kontron or one of its authorized agents.
The information contained in this document is, to the best of our knowledge, entirely correct. Howev-
er, Kontron cannot accept liability for any inaccuracies or the consequences thereof, or for any liability
arising from the use or application of any circuit, product, or example shown in this document.
Kontron reserves the right to change, modify, or improve this document or the product described here-
in, as seen fit by Kontron without further notice.
Trademarks
This document may include names, company logos and trademarks, which are registered trademarks
and, therefore, proprietary to their respective owners.
Environmental Protection Statement
This product has been manufactured to satisfy environmental protection requirements where possible.
Many of the components used (structural parts, printed circuit boards, connectors, batteries, etc.) are
capable of being recycled.
Final disposition of this product after its service life must be accomplished in accordance with appli-
cable country, state, or local laws or regulations.

8
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
1 Introduction
1.1 Carrier Overview
The COMe Reference Carrier-i Type 10 Thin-NanoITX (hereinafter referred to as COMe Ref. Carrier-i T10
TNI) is a COM Express® pinout Type 10, Thin-nITX form factor-compliant reference carrier designed to
accommodate a mini Type 10 COM Express® Computer-on-Module compliant with the PICMG COM.0
specification Rev 2.1.
The COMe Ref. Carrier-i T10 TNI comes in three variants:
» COMe Reference Carrier-i Type 10 Thin-NanoITX Professional (COMe Ref. Carrier-i T10 TNIP),
» COMe Reference Carrier-i Type 10 Thin-NanoITX Value (COMe Ref. Carrier-i T10 TNIV), and
» COMe Reference Carrier-i Type 10 Thin-NanoITX Entry (COMe Ref. Carrier-i T10 TNIE).
The following table provides information about the features implemented on the COMe Ref. Carrier-i
T10 TNI variants.
Table 1: COMe Ref. Carrier-i T10 TNI Variants
COMe Ref. Carrier-i T10 TNIP
(P/N 34105-0000-00-0)
COMe Ref. Carrier-i T10 TNIV
(P/N 34105-0000-00-1)
COMe Ref. Carrier-i T10 TNIE
(P/N 34105-0000-00-2)
SPI BIOS Socket xxx
Carrier EEPROM xxx
DDI0 - DP++ xxx
LVDS xxx
mDP++ (eDP) -- -- --
mPCIe0 xx--
mPCIe1 / mSATA xxx
GBLan0 (Module) xxx
GBLan1 (Carrier) xx--
SATA0 xxx
USB 2.0 / 3.0 I/O xxx
USB 2.0 Header xx--
HDA Codec xx--
Line-In/Out xx--
S/PDIF xx--
SER0 xxx
GPIO xxx
microSD/SIM xx--
Sys Signals xxx
Sys Panel xxx
CPU Fan xxx
RTC connector xxx
Goldcap 1.5F xx--
SMART Battery x----
12V Input xxx
6.5 - 30V Input x----
Rubber Feet x----

9
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
1.2 Board Diagrams
The following diagrams provide additional information concerning board functionality and component
layout.
1.2.1 Functional Block Diagram
Figure 1: COMe Ref. Carrier-i T10 TNI Functional Block Diagram
SDIO
GBE#0
PCIe #1
USB 2.0 #5
PCIe #0
USB 2.0 #4
LVDS/eDP
EXT_FAN
PWRBTN# / SYS_RESET / HDD_ACT / SYS_LED
GPIO
I2C / SMB / WDT / LID / Sleep
SER0
DDI
C
O
N
N
E
C
T
O
R
A
BµSD Card
Switch
GPIO/SDIO
HDA
HD Audio
SPKR
SYS_Panel
S/PDIF In/Out
USB 2.0 USB #6/7
DP
JILI/LVDS
mDP
COM1
Battery Connector
Goldcap
GPIO Header
SYS Signals
Front Panel
CPU_FAN
Line In/Out
USB 2.0 #0/1
USB 2.0 #2/3
USB 2.0
USB 3.0
DS
USB-PWR
USB 3.0 #0/1
Mini PCIe
Mini PCIe
mSATA
SIM Card
Switch
DS
SATA
Ethernet
Ethernet GBE
GBE#1
DS
5V_SB DS
12V
6.5-30V
I/O Power to
Peripherals
Power
7.2V SMART Battery
Internal connector
or pin header
IO Shield
Configuration
jumper
Component
DS EEPROM
SPI Flash
PCIe #2
SATA #1
SATA #0
optional
RTC

10
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
1.2.2 Rear Panel
Figure 2: COMe Ref. Carrier-i T10 TNI Rear Panel
1.2.3 Board Layout
Figure 3: COMe Ref. Carrier-i T10 TNI Layout - Top View
DisplayPort
miniDP
LAN LAN USB
2.0
USB
3.0/2.0
J6
J10
U22
J2
J5
J7
J11
J12
J13
J14
J15
C181
J16 J17
J18
J19
J20
J1
J22
J23
J3
SW1
J24
J21
A1
B1 B110
A110
J8
J4
J9
D3
D2
1
1
4
12
14
10
11
1
14
10
11
1
14
4
18
11
1
1
S1
S7
P1
P15
1
1
S4
S1
T8
T1
1
10
1
2
12
11
1
1
1

11
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
Figure 4: COMe Ref. Carrier-i T10 TNI Layout - Bottom View
J25
J26
J27 J28
U23
U29
U27
51
1
52
2
51
1
52
2

12
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
1.2.3.1 Component Overview
Table 2: Component Overview
COMPONENT DESCRIPTION
C181 Goldcap
D2 Status LED: V12_S0
D3 Status LED: V5.0_S5
J1 SATA plug connector (with power connector)
J2 PWM fan connector
J3 Smart Battery Input
J4 RJ45 Ethernet connector
J5 Front panel connector
J6 SYS_Signals / embedded interfaces pin header
J7 RJ45 Ethernet connector
J8 COM port pin header (COM1/SER0)
J9 USB 3.0/2.0 double-stack connector
J10 USB 2.0 header
J11 GPIO pin header
J12 COMe connector (Row A and B)
J13 USB 2.0 double-stack connector
J14 CMOS battery connector
J15 LVDS / JILI connector
J16 Mini DisplayPort++ connector (eDP option)
J17 DisplayPort++ connector (DDI0)
J18 SPI BIOS socket
J19 Power connector (6.5V – 30V input voltage)
J20 microSD/SIM combo connector
J21 DC jack (12V only)
J22 Rear panel line-in connector
J23 Rear panel SPK / line-out connector
J24 S/PDIF Header
J25 Mini PCIe card latch (full-size) / mSATA socket
J26 Mini PCIe card slot (full-size) / mSATA socket
J27 Mini PCIe card latch (half-size)
J28 Mini PCIe card slot (half-size)
SW1 DIP switch
U22 Carrier EEPROM (FRUPROM)
U23 Intel® Ethernet Controller I210-IT
U27 Smart Battery Controller TI BQ24725A
U29 HD Audio Codec IDT / Tempo Semi 92HD73C

13
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
1.3 Technical Specification
Table 3: COMe Ref. Carrier-i T10 TNI Main Specifications
FEATURES SPECIFICATIONS
CPU
Processor & Chipset Via COMe mini Type 10 module
Memory
System Memory Via COMe mini Type 10 module
Flash Memory One SPI BIOS socket for an SPI flash IC with up to 8 MB flash memory
EEPROM EEPROM with 32 kbit on the carrier (FRUPROM)
Graphics Interfaces
Digital Display Interface One digital display interface (DDI0):
» DDI0: DisplayPort++ connector from COMe DDI0, J17
LVDS LVDS / JILI connector (24-bit, single-channel LVDS), J15
Embedded DisplayPort Mini DisplayPort++ connector via eDP (optional, instead of LVDS), J16
System Interfaces
PCI Express Three PCIe interfaces:
» PCIe#0 for Mini PCIe 2.0 half-size card slot connected to the microSD/SIM
combo socket, J28
» PCIe#1 for Mini PCIe 2.0 full-size card slot muxed with SATA#1 (mSATA) and
connected to the microSD/SIM combo socket, J26
» PCIe#2 for the onboard Gigabit Ethernet controller
SATA Two SATA 3 Gb/s interfaces:
» SATA#0 via the 22-pin SATA plug connector, J1
» SATA#1 for the mSATA socket / Mini PCIe full-size card slot, J26
Ethernet Two Gigabit Ethernet interfaces:
» GbE#0 on RJ45 connector, J4, via COMe mini Type 10 module
» GbE#1 on RJ45 connector, J7, via the onboard GbE controller (Intel® Ether-
net Controller I210-IT)
USB 2.0 Eight USB 2.0 interfaces:
» Two USB 2.0 interfaces (USB#[0;1]) for USB 3.0/2.0 double-stack connector,
J9
» Two USB 2.0 interfaces (USB#[2;3]) for USB 2.0 double-stack connector, J13
» One USB 2.0 interface (USB#4) for PCIe#0 (Mini PCIe half-size interface)
» One USB 2.0 interface (USB#5) for PCIe#1 (Mini PCIe full-size/mSATA inter-
face)
» Two USB 2.0 interfaces (USB#[6;7]) for USB 2.0 pin header, J10
USB 3.0 Two USB 3.0 interfaces:
» Two USB 3.0 interfaces (USB_SS#[0;1]) for USB 3.0/2.0 double-stack con-
nector, J9
HD Audio Three HD Audio interfaces:
» Rear panel line-in connector, J22
» Rear panel SPK/line-out connector, J23
» S/PDIF header, J24
UART One RS-232 COM port (RX/TX only) via pin header, J8 (COM1/SER0)
GPIO/SDIO Either four GPIs and four GPOs via the 10-pin GPIO pin header, J11, or
alternatively SDIO usage via microSD/SIM combo socket

14
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
System Interfaces
SIM microSD/SIM combo socket, J20, connected to both Mini PCIe interfaces
I2CI
2C interface via 15-pin SYS_Signals / embedded interfaces pin header, J6
SMBus SMBus interface via 15-pin SYS_Signals / embedded interfaces pin header, J6
LID/SLEEP LID/SLEEP signals via 15-pin SYS_Signals / embedded interfaces pin header, J6
CPU Fan One 4-pin PWM fan connector, J2
LEDs Two status LEDs available via the front panel connector, J5:
»PowerLED
» HDD Activity LED
Switch
DIP Switch One 8-position DIP switch, SW1, for board configuration
Power Supply and
Management
Power Supply Power input 1: 12V only
Power input 2: 6.5V - 30V wide input range
SMART battery: 7.2V - 8.4V
Power / Reset Button Available via the front panel connector, J5
RTC 2-pin connector for external CMOS battery, J14
Goldcap for RTC backup, C181
General
BIOS Via COMe mini Type 10 module
Temperature Range Operational: -40°C to +85°C
Storage: -40°C to +85°C
Note: When additional components are installed, refer to their operational
specifications as this will influence the operational and storage
temperature of the COMe Ref. Carrier-i T10 TNI.
Climatic Humidity 93% RH at 40 °C, non-condensing (acc. to IEC 60068-2-78)
Form Factor COM Express® carrier, pinout Type 10, Thin-nITX form factor
Dimensions 120 mm x 120 mm (nITX)
Max. component height:
Top side: 16.5 mm
Bottom side: 4.0 mm
Table 3: COMe Ref. Carrier-i T10 TNI Main Specifications (Continued)
FEATURES SPECIFICATIONS

15
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
1.4 Accessories
The following accesssories are available for the COMe Ref. carrier-i T10 TNI.
Table 4: COMe Ref. Carrier-i T10 TNI Accessories
Part Number Part Name Description
96006-0000-00-1 COMe Post T10 NFCB POST Code / Debug card
38019-0000-00-1 ADA-COMe-Height-single EERC Height Adapter
34017-0000-00-0 COMe mMount Kit 5/8 mm 1 set Mountig Kit for 1 Module including screws for
5 mm and 8 mm connectors
9-5000-0352 ADA-LVDS_DVI 18 bit 18 bit LVDS to DVI converter
9-5000-0353 ADA-LVDS_DVI 24 bit 24 bit LVDS to DVI converter
96006-0000-00-8 ADA-DP-LVDS DP to LVDS adapter
96082-0000-00-0 KAB-ADAPT-DP-DVI DP to DVI adapter cable
96083-0000-00-0 KAB-ADAPT-DP-VGA DP to VGA adapter cable
96084-0000-00-0 KAB-ADAPT-DP-HDMI DP to HDMI adapter cable

16
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
1.5 Standards
This product complies with the requirements of the following standards.
Note: Customers desiring to perform further environmental testing of the COMe Ref. Carrier-i T10
TNI must contact Kontron for assistance prior to performing any such testing.
Boards without conformal coating must not be exposed to a change of temperature which
can lead to condensation, as it may cause irreversible damage especially when the board
is powered up again.
Kontron does not accept any responsibility for damage to products resulting from destruc-
tive environmental testing.
Table 5: Standards
TYPE ASPECT STANDARD REMARKS
CE Emission EN61000-6-3, EN55022 --
Electrical Safety Directive 2014/35/EU Low Voltage Directive (LVD)
EN60950-1 --
Product Safety Directive 2001/95/EC General Product Safety Directive
EMC Directive 2014/30/EU Electromagnetic Compatibility
Environmental Climatic Humidity IEC60068-2-78 (see note below) --
WEEE Directive 2002/96/EC Waste electrical and electronic
equipment
RoHS 2 Directive 2011/65/EU Restriction of the use of certain
hazardous substances in electri-
cal and electronic equipment
Environmental Vibration
(Sinusoidal)
IEC60068-2-6 Test parameters:
9-150 (Hz) frequency range
1 (g) acceleration
1 (oct/min) sweep rate
10 cycles/axis
3 axes
Single Shock IEC60068-2-27 Test parameters:
15 (g) acceleration
11 (ms) shock duration half sine
3 number of shocks per direction
(total: 18)
6 directions
5 (s) recovery time

17
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
1.6 Related Publications
The following publications contain information relating to this product.
Table 6: Related Publications
PRODUCT PUBLICATION
COM Express® COM Express® Carrier Design Guide Rev 2.0
COM Express® Module Base Specification Rev 2.1
SATA Serial ATA Specification Revision 3.0
PCI Express PCI Express Base Specification Rev 2.0
PCI Express M.2 Specification Rev 1.0
DisplayPort Display Port 1.1a Standard
Display Port 1.2 Standard
USB Universal Serial Bus (USB) 2.0 Specification Rev 2.0
Universal Serial Bus (USB) 3.0 Specification Rev 1.0
SD SD Spec. Part A2 SD Host Controller Standard Spec. Version 2.00
SD Spec. Part E1 SDIO Spec. Version 2.00
SD Spec. Part 2 File System Spec. Version 3.00
SD Spec. Part 1 Physical Layer Spec. Version 3.00
I2CI2C Bus Specification Version 4.0
SMBus SMBus Specification Version 2.0
ACPI ACPI spec Rev 5.0

18
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
2 Functional Description
2.1 Memory
2.1.1 SPI Flash
The COMe Ref. Carrier-i T10 TNI provides one SPI BIOS socket, J18, for SPI flash ICs with up to 8 MB
flash memory for use with an external Carrier BIOS. Recommended SPI flash ICs include Winbond
W25Q64FVSSIG (8MB) and Atmel AT25DF321A-SH (4MB), depending on the COMe module used. Boot-
ing from the Carrier SPI flash can be enabled or disabled via the onboard DIP switch SW1.
2.1.2 Carrier EEPROM
The COMe Ref. Carrier-i T10 TNI comes with an onboard 32-kbit I²C EEPROM, U22, for storage of manu-
facturer records or COMe module information.
2.2 Graphics Interfaces
2.2.1 Digital Display Interfaces
The COMe Ref. Carrier-i T10 TNI provides the following digital display interface (DDI):
» DDI0 from the COMe module is directly mapped to the DisplayPort++ connector, J17

19
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
2.2.2 LVDS/eDP Interface
The COMe Ref. Carrier-i T10 TNI supports a 24-bit, single-channel LVDS interface via the LVDS/JILI con-
nector, J15.
The following figure and table provide pinout information for the LVDS/JILI connector, J15.
If eDP support is required, the COMe Ref. Carrier-i T10 TNI may optionally be equipped with a Mini Dis-
playPort++ connector, J16, instead of the LVDS/JILI connector, J15.
Note: In order to use the eDP interface, the COMe module installed must also support eDP.
Figure 5: LVDS/JILI Connector J15
J15
140
Table 7: LVDS/JILI Connector J15 Pinout
PIN SIGNAL PIN SIGNAL
1LVDS_BKLT_CTRL 21NC
2LVDS_A0- 22GND
3LVDS_A0+ 23NC
4 LVDS_VDD_EN 24 NC
5LVDS_A1- 25GND
6LVDS_A1+ 26NC
7NC 27NC
8LVDS_A2- 28GND
9LVDS_A2+ 29NC
10 GND 30 NC
11 LVDS_A_CK- 31 +5V
12 LVDS_A_CK+ 32 +5V
13 GND 33 +5V
14 LVDS_A3- 34 +5V
15 LVDS_A3+ 35 LVDS_BKLT_EN
16 LVDS_I2C_DAT 36 GND
17 NC 37 GND
18 NC 38 +12V
19 LVDS_IC2_CK 39 +12V
20 NC 40 +12V

20
www.kontron.com
User Guide
COMe Ref. Carrier-i T10 TNI
2.3 System Interfaces
2.3.1 PCI Express Interfaces
The COMe Ref. Carrier-i T10 TNI provides three general-purpose PCI Express (PCIe) lanes:
» PCIe#0 for the Mini PCIe half-size card slot, J28, connected to the microSD/SIM combo sock-
et, J20
» PCIe#1 for Mini PCIe full-size card slot, J26, muxed with SATA#1 (mSATA), connected to the
microSD/SIM combo socket, J20. Mini PCIe may be enabled via the onboard DIP switch SW1.
» PCIe#2 for onboard Gigabit Ethernet Controller, U23
Note: The MiniPCIe half-size card slot, J28, is available as a standard feature on the COMe Ref.
COMe Ref. Carrier-i T10 TNIV (Value) and the COMe Ref. Carrier-i T10 TNIP (Professional)
versions.
2.3.2 SATA Interfaces
The COMe Ref. Carrier-i T10 TNI supports up to two SATA 3 Gb/s interfaces:
» SATA#0 via the 22-pin SATA plug connector, J1
» SATA#1 for the mSATA socket / Mini PCIe full-size card slot, J26, muxed with PCIe#1 (Mini
PCIe). mSATA may be enabled via the onboard DIP switch, SW1.
2.3.3 Gigabit Ethernet Interfaces
The COMe Ref. Carrier-i T10 TNI provides up to two Gigabit Ethernet interfaces via two single RJ45 con-
nectors:
» GBE#0 on RJ45 Ethernet connector, J4, directly via the COMe mini Type 10 module
» GBE#1 on RJ45 Ethernet connector, J7, via the onboard Intel® Ethernet Controller I210-IT,
U23 (on PCIe#2)
The Ethernet connector LEDs have the following states:
LINK (green): Ethernet Link
ACT (green): 1000BASE-T Ethernet Speed
ACT (yellow): 100BASE-TX Ethernet Speed
ACT (off) + LINK(on): 10BASE-T Ethernet Speed
Note: The RJ45 Ethernet connector, J7, and the Intel® Ethernet Controller I210-IT, U23, are
available as a standard feature on the COMe Ref. Carrier-i T10 TNIV (Value) and the COMe
Ref. Carrier-i T10 TNIP (Professional) versions.