Korenix JetNet 3010G Series User manual

JetNet3010G
7 10/100TX + 3 Gigabit SFP/Gigabit Copper
Industrial Gigabit Switch
User’s Manual
Version: 2.1, Jun-2011

Korenix JetNet 3010G Series
Industrial Gigabit Ethernet Switch
User’s Manual
Copyright Notice
Copyright ©2008 Korenix Technology Co., Ltd.
All rights reserved.
Reproduction in any form or by any means without permission is prohibited

1. Introduction..........................................................................................4
1-1. Features...........................................................................................4
1-2. Packing Check List..........................................................................4
2. Hardware Description..........................................................................6
2-1. Dimension........................................................................................6
2-2. Front Panel......................................................................................7
2-3. Bottom View.....................................................................................7
2-4. Wiring the Power Input.....................................................................8
2-5. wiring the Earth ground....................................................................9
2-6. LED Indicators...............................................................................10
2-7. Ethernet interface introduction.......................................................11
2-8. Quality of Service...........................................................................11
2-9. Wiring Cable..................................................................................12
3. Mounting Installation.........................................................................13
3-1. DIN Rail Mounting..........................................................................13
3-2. Wall Mounting................................................................................14
4. Hardware Installation.........................................................................16
4-1 Installation and Testing ...................................................................16
5. Trouble Shooting................................................................................20
6. Technical Specification .....................................................................20
7. SFP Fiber Transceiver Order Information........................................22

1. Introduction
In the traditional industrial communication, the communicate infrastructure is combined
with proprietary protocol and hard to connect with different layer. Today, the new trend
of industrial communication is integrated all of layers to Ethernet protocol. As the
bandwidth demands is growing up by several of applications, like video security, traffic
signal monitoring and control; this is a need of Gigabit Ethernet becomes popular in
recently.
The JetNet3010G is a 10-port Gigabit Industrial switch which embedded 7-port
10/100TX and 3 combo ports for Gigabit copper and SFP for Gigabit Ethernet uplink.
With the high bandwidth switch fabric, JetNet3010G can deliver full wire speed without
packet loss. This manual will introduce JetNet3010G hardware specification, system
installation and the applications.
1-1. Features
7 10/100TX and 3 Gigabit copper/SFP combo
IEEE802.3, 802.3u, 802.3z and 802.3ab Compliance
Auto detection Gigabit Transmission Media
Flexible Gigabit Fiber Link Distance
High performance 32Gbps Switch fabric
Supports Auto MID/MDI-X with Flow control
IEEE802.1p for Quality of Service (QoS)
Power redundancy with wide range input
1.5KV Hi-pot passed for Port, Power, Case
Rigid IP31 grade Aluminum Case
-10~60℃Hazardous Operating Temperature
1-2. Packing Check List
JetNet3010G package include the following items:
JetNet3010G x1

One DIN-Rail clip (already screwed on the back of JetNet3010G) x1
One wall mounting plate
User’s manual
Quick Installation Guide
JetNet3010G Industrial Switch User’s Manual CD-ROM Quick Installation Guide
WallMountingPlate Screwx4(M3x6mm)
Contact your sales representative if any item is missing or damaged.

2. Hardware Description
This session will introduce the enclosure interface, system power installation,
dimension and the QoS.
2-1. Dimension
The dimension of JetNet3010G is 96 mm (w) x 137 mm (H) x 119 mm (D)

2-2. Front Panel
The following diagram shows the front panel of JetNet 3010G, it describes the LEDs,
Fast Ethernet and Gigabit Ethernet ports.
Figure A. Front Panel of JetNet 3010G
2-3. Bottom View
The bottom view of the JetNet3010G Industrial Gigabit Switch consists of one
terminal block connector with two DC power inputs.

Figure B. Bottom view of the JetNet3010G Industrial Gigabit Switch
2-4. Wiring the Power Input
The JetNet 3010G supports 2 power inputs with power redundance and polarity auto
reverse functions; the typically input power voltage is DC 24V with 12~48V input range.
On the bottom side, there is one 4-pin removable terminal block for the redundant
power input and the suitable specification of power cable is 12 ~24 AWG.
Following the instructions as below to wiring the cable and switching power system.
1. Insert the positive and negative wires into the V+ and V- contacts respectively of
the terminal block connector
2. Tighten the wire-clamp screws to prevent the DC wires from being loosened.
3. The Power 1 and Power 2 support power redundancy and polarity reverse
protection functions.
4. It accepts positive or negative power system input, but Power 1 and Power 2
have to apply the same mode.

Note 1: It is a good practice to turn off input and load power, and to unplug power
terminal block before making wire connections. Otherwise, your screwdriver blade
can inadvertently short your terminal connections to the grounded enclosure.
Note 2: The range of the suitable electric wire is from 12 to 24 AWG.
Note 3: If the 2 power inputs are connected, JetNet 3010G will be powered from the
highest connected voltage. The unit will alarm for loss of power, either PWR1 or
PWR2.
Note 4: To use the UL Listed LPS Power supply with output Rating 12-48 Vdc,
minimum 1 A
2-5. wiring the Earth ground
To ensure that the system will not be damaged by noise or any electrical shock, we
suggest you make exactly connection with JetNet3010G with Earth Ground.
On the bottom side of JetNet3010G, there is one earth ground screw, loosen the earth
ground screw by screw drive and tighten the screw after earth ground wire connected
Earth Ground

2-6. LED Indicators
The front panel of JetNet3010G includes 2 Power LEDs, 6 LEDs for Gigabit SFP and
RJ-45 ports. Each 10/100Base-TX ports includes 2 LEDs with Green and Yellow color.
These LED indicators provide administrators with real-time system status. Table 1
gives descriptions of the function of each LED indicator.
LED Status Description
Green Power 1 is supplying DC power.
Power 1 Off No power is being supplied.
Green Power 2 is supplying DC power.
Power 2 Off No power is being supplied.
Green A network device is detected.
Blinks The port is transmitting or receiving
packets from the TX device.
RJ-45
(Gigabit Port 8~10)
Off No device is attached or not link
with RJ-45 port.
Green The port is transmitting or receiving
packets from the TX device.
Blinks The port is transmitting or receiving
packets from the TX device
SFP
(Gigabit Port 8~10)
Off No device is attached or not link
with RJ-45 port.
Green A network device is detected.
Blinks The port is transmitting or receiving
packets from the TX device
10/100Mbps
(Port 1 ~7)
off No device is attached or not link
with RJ-45 port.
Notes 1: It is recommended don’t connect SFP fiber transceiver and RJ-45
combo port at same time; it will cause internal wrong link signature detection
and get wrong network connection.
Notes 2: Gigabit Port 10 supports 1000Base-T (1000Mbps) or Gigabit Fiber only,
but port 8 and 9 support 10/100/1000Mbps or Gigabit Fiber