Korenix JetNet3008G V2 User manual

Mount the unit
Din-Rail mount: Mount the din-rail clip on the rear of
JetNet 3008G v2 on
the DIN rail. For information about the DIN Rail
installation, please refer to user’s manual.
Grounding JetNet 3008G v2
There is one grounding screw on the bottom side of
JetNet 3008G V2. Connect the earth ground screw of
JetNet3008G v2 to the grounding surface to ensure
safety
and prevent noise.
JetNet 3008G is an 8-port full Gigabit Industrial Ethernet
Switch, conforming IEEE 802.3u and 802.3ab standard ,
supports 8 10/100/1000 Based TX. The JetNet 3008G
adopts rugged metal case design to operate in harsh
environment (-40~70°C ). It features one relay output to
alarm users if a port link fails or with the power fails.
Alarm can be enable/disabled by a dip switch. JetNet
3008G v2 is recommended to be powered by DC 24V with
9-60V ranged.
JetNet3008G V2
Quick Installation Guide v1.0
Copyright
Copyright © 2014 all rights reserved. No part of this
publication may be reproduced, adapted, stored in a
retrieval system, translated into any language, or
transmitted in any form or by any means without the
written permission of the supplier.
About the Quick Installation Guide
This Quick Installation Guide is intended to guide
professional installer to install and configure the JetNet
3008G v2. It covers procedures to assist you in avoiding
unforeseen problems.
Installation
Introduction
Wiring the Relay Output
The relay output contacts are at the right side of the
terminal block connector as shown below. By inserting the
wires and settings the DIP switch of the respective alarm
function to “ON”, relay output alarm will detect port or
power fault, and avoid form a short circuit. The alarm
relay output is “Normal Open”. For more information,
please refer Manual chapter for more detail.
Note:
The relay contact only support 0.5A current, DC 24V. It
does not recommend apply higher voltage and current
that over this specification.
Connecting to Network
Connecting the Ethernet Port: Connect one end of an
Ethernet cable into the UTP port of JetNet 3008G v2, while
the other end is connected to the attached networking
device. UTP port support auto MDI/MDIX function. The LNK /
ACT LED will turn on for link up and blinking for packet
transmit and receive. The Speed LED will turn on for Gigabit
link and turn off for 10/100Mbps link.
DIP Switch Setting
Note:
After adjusting the DIP-switch, please reboot the unit to
activate the new settings.
Package Check List
JetNet 3008G v2 Ethernet switch
Quick Installation Guide
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with
high industrial standard. Korenix warrants that the Product(s) shall be
free from defects in materials and workmanship for a period of five (5)
years from the date of delivery provided that the Product was properly
installed and used.
This is warranty is voided if defects, malfunctions or failures of the
warranted Product are caused by damage resulting from force measure
(such as floods, fire, etc.), other external forces such as power
disturbances, over spec power input, or incorrect cabling; or the
warranted product is misused, abused, or operated, altered and repaired
in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT
plug in power connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU
of the European Parliament and of the Council of 27 January 2003 on the
restriction of the use of certain hazardous substances in electrical and
electronics equipment (RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our
professional staff are ready to solve your problems at any time Korenix
global service center's e-mail is [e-mail].
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
Support
Pin
No. #
Status
Description
P1
to P8
(Pin1
~8)
ON
T
o enable port link down alarm at this port.
Off
T
o disable port link down alarm at this port.
P9
ON
T
o enable power failure alarm.
Off
T
o disable power failure alarm.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V-
contact on
the terminal block connector.
2. Tighten the wire-clamp screws to prevent the power wires
loosened.
Note:
The recommended working voltage is DC 24V. (Input range:
DC9~ 60 V)

连接到网络
1. 连接以太网端口：将以太网电缆的一端连接到JetNet
3008G V2的UTP端口，另一端连接到所连接的网络设备。
UTP端口支持自动MDI/ MDIX功能。 LNK / ACT LED将亮
起并闪烁，表示RJ-45端口链路和从RJ-45接收和发送的数
据包。
注意:
推荐的输入电压为DC 24V。(可输入范围：DC9〜60V)
接线输出
继电器输出触点位于连接器端子中间，如下所示。 透过将警报功能
的DIP开关插入到“ON”，继电器输出报警将检测端口或电源故障，
并形成短路。 有关更多信息，请参阅手册章节了解更多详细信息。
版权
版权所有©2014保留所有权利。 未经供应商书面许可，不得将
本出版物的任何部分复制，改编，存储在检索系统中，翻译成任
何语言，或以任何形式或方式传播。
关于快速安装指南
本“快速安装指南”旨在指导专业安装人员安装和配置JetNet
3008G V2。 它涵盖了帮助您避免意外问题的程序。
常规
警告:此符号表示您必须遵守的警告
注意:此符号表示您必须注意的重要注意事项。
安装
介绍
注意:
继电器触点仅支持0.5A电流，DC 24V。 不建议
使用超过本规范的更高的电压和电流。
Din-Rail支架：
将JetNet 3008G V2背面的Din-rail夹子安装在DIN导轨。有关
DIN导轨安装的信息请参考用户手册。
JetNet 3008G V2 接地:
JetNet 3008G v2底部有一个接地
螺丝。 将JetNet3008G V2连接框
架接地以保证安全，防止噪音造成
通信干扰。
输入电源接线:
1.将正极和负极线插入端子块连接器上的V +和V-触点。(如右上
图)
2.拧紧电线夹螺钉，防止电源线松动。
JetNet 3008G v2 是全千兆工业以太网交换机，符合IEEE
802.3u 和802.3ab 标准，支持8个10/100/1000Base TX 端
口，
JetNet 3008G v2 交换机采用坚固的铝合金外壳结构设计, 能
够在恶劣的工业环境(-40~70˚C) 穏定工作, 符合IP31工业防
护标准, 它还支持一路继电器报警输出, 可针对断线/断电状态
提供现场报警服务, 此继电器警告功能可透过交换机前面板的
DIP拨码开关做启动或关闭.JetNet 3008G v2 在机身底部装有
可拆缷电源线槽, 其输入电源范围是9~60V, 建议采用穏定的
24Ｖ直流电为设备供电
打開包裝，檢查下列配件
•JetNet 3008G V2 工业媒体转换器*1
•快速安装指南*1 Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
Tel:[phone]
Fax:[phone]
Business service:[e-mail]
Customer service:
[e-mail]
www.korenix.com
CPQ000N3008008
Patent No. (Taiwan):
Granted Invention: I
313547
Granted Invention: I
321415
Granted Invention: I
344766
Granted Invention: I
346480
Granted Invention: I
356616
Granted Invention: I
364684
Granted Invention: I
376118
Granted Invention: I
393317
Granted Invention: I
398066
Granted Invention: I
398125
Granted Invention: I
459757
Utility Model: M
339841
Utility Model: M
339840
客户服务
5年质保
所有科洛理思产品的设计、制造及测试都是采用较高的工业
标准。科洛理思保证自产品出货日起提供最高5 年之免费保
修服务，保修期间如因零件损坏或制程不良而导致产品故障，
我们提供免费维修服务。自然外力 （火、水、雷灾）所造成
的产品故障，或其它外部因素如电源干扰、不当电源输入、
不当接线等造成的损坏，不列入产品保固范围；此外，产品
被误用、未经授权的修理及修改等行为将造成保固条款失效。
注意! 请勿于电源开启时插拔接线端子，避免产生火花造
成系统损坏。
此产品保证完全符合欧盟2003年1月27日电气和电子设备
危害物质限制委员会限用指令2002/95/EC (RoHS)及
2011/65/EU(RoHS 2.0)。
Korenix售后服务
KoreCARE 是科洛理思科技全球服务中心，我们专业的技
术人员随时准备解答您的疑问。
科洛理思全球服务中心 EMAIL: [email protected]om
业务服务: [email protected]m.cn
官网: www.korenix.com.cn
Pin
No. #
Status
Description
P1
to P8
(Pin1
~8)
ON
T
o enable port link down alarm at this port.
Off
T
o disable port link down alarm at this port.
P9
ON
T
o enable power failure alarm.
Off
T
o disable power failure alarm.
DIP拨码开关设定
注意:
1. 调整DIP开关后，请重新启动本机以激活新设置