Korpinen Gaius Original 21273108-00 User manual

D012224
Manual
21273108-00 Electric Original basin lifter

D012224
Manual
Description
This manual describes the installation process and hole placements for the 21273108-00
Electric Original basin lifter.
ID
Item Revision
D012224
A.2
Type
Installation instructions
Subject
Owner
korpinen_admin
Owning Group
Korpinen

D012224
Manual
1
Symbols used in this manual
Warning!
Indication of potentially hazardous situation. If not
avoided, it can result in serious injury or death.
Caution!
Indication of potentially hazardous situation which may
result in minor or moderate injury.
It may also be used to alert against unsafe practices.
Notification!
This symbol is used to notify correct use and handling of
the product.
General safety
This manual must be read and understood before use and
installation. Always keep this manual in close proximity of
the product.
The use, installation and service of this product must follow
this manual to avoid accidents and serious personal injury.
Never use or handle this product in other ways specified in
this manual as it can result in personal safety hazards and/or
cause damage to the product.
Persons installing and/or using this product either as
operator or user should have the necessary safety
information and access to this manual.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or duly qualified designated
persons in order to avoid a hazard.

D012224
Manual
2
Do not perform unauthorized repairs, disassembly or
assembly operations, add-ons, re-adjustments or
modification of the product beyond what is described in
this manual. Any use, modification or adjustment not
described in the most recent approved revision of the
manual is strictly forbidden. Do not perform service while the
product is connected to the mains power.
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given adequate supervision or instruction
concerning the safe use of the appliance and they
understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall
not be performed by children without supervision.
Do not use the product if it has defects or signs of damage
are present. If the device makes unusual noise or smells,
switch off the mains voltage immediately.
Take care that the cables are not damaged. Unplug the
mains cable on mobile equipment before it is moved.
The products must only be used in an environment that
corresponds to their IP protection.
The information in this manual is based on correct
installation in accordance with installation instructions for
this product.
Korpinen cannot be held liable if the product is used in any
way that differs from stated in this manual and/or
installation instruction. Korpinen reserves the right to amend
this manual and reference documents without prior notice.

D012224
Manual
3
Product label symbols
This product is CE-marked in accordance with:
Council Directive 2006/42/EC on machinery
Council Directive 2011/65/EU, RoHS
Manufacturer name and address
Date of production
Stock number
Serial number
Consult manual before use
Operating interval of electrically operated equipment. The use of
electrical height adjustable equipment can run at maximum 2
minutes, followed by an 18-minute break.
Type B applied part. The product complies with IEC 60601-1
requirements to provide protection against electric shock.
Consult manual for important safety related information, warnings,
and safety precautions.
Class II, double isolated electrical components.
Do not dispose as unsorted municipal waste. Product must be
returned to a designated recycling station.
Mobile phones or other portable RF emitting equipment should be no
closer to the product than 30cm.
Operating and storing temperatures may not exceed 5-40°C

D012224
Manual
4
Exploded view
1 pcs. Lifting unit
1 pcs. 6203
Original basin
(Sold separate)
1 pcs. Bottom
cover
1 pcs. Top cover
1 set Basin
support arms
1 pcs. 13982
Drain pipe (sold
separate)
1 pcs. Faucet
with 10mm inlet
tubing (Sold
separate)
1 pcs. Operating
interface

D012224
Manual
5
Drain area
Electrical outlet
230VAC IP44
Max dimensions:
Height 15 mm
80 x 80 mm or d80
Water inlets

D012224
Manual
6
Figure 1. Mounting screw, water inlet, drain and mains power placement
IMPORTANT NOTICE! Floor drain should extend at least 235 mm from the floor. Tube
diameter 32 –40 mm. Tube center distance from wall 50-60 mm.

D012224
Manual
7
Figure 2. Reinforced area (Plywood 20 mm with full thread screws) and external dimensions

D012224
Manual
8
1. Install the basin support arms and the operating interface
Make sure the support
arms are mounted as far
as they will go.

D012224
Manual
9

D012224
Manual
10
Install the cable
tie mounts and
route the
controller wiring
as pictured.
Leave a 140-150
mm loop of wire
between the leg
and basin support
arm, this enables
the unit to move.

D012224
Manual
11
2. Predrill all necessary holes. Refer to Fig. 1 for mounting
hole positions. Install the top mounting screws into the
wall.
IMPORTANT NOTICE! Please
leave a 10mm gap
between the wall and the
screw head.
NOTICE! If the wall
material requires the use
of a wall plug, silicone
caulk should be used in
the holes.
NOTICE! Mounting hardware sold
separate
Korpinen part no. 6219-Z
Or 8 pcs. Full thread 8x60mm
deck screws with adequate wall
plugs

D012224
Manual
12
3. Lift the lifting unit on top of the top screws in the wall.
Using a spirit level, ensure that the unit is installed level.
4. When the unit is level, tighten the top screws; insert and
tighten the bottom screws. Plug the lifter to mains power
and test it before adhering the basin.
IMPORTANT NOTICE! Use a
spirit level to ensure the
unit is installed level
IMPORTANT NOTICE! Test
the unit before moving to
the next step.
IMPORTANT NOTICE! While testing, keep hands and
tools away from the open mechanism. Before
continuing work, unplug the unit.

D012224
Manual
13
5. Assemble the faucet, basin and plumbing
NOTICE! Plumbing
hardware sold separate.
Korpinen product
numbers 13970 & 13982
IMPORTANT NOTICE!
Air lock must be
pressed and fixed to
the top position with
a cable tie. Flexible
drainpipe must be
held in place with a
hose clamp.
IMPORTANT NOTICE!
Cut the faucet tubes
to length. The faucet
tubes must be 10mm
in diameter
NOTICE! 13982 Flexible
drain pipe sold separate.
NOTICE! Remember
to move the air lock
O-ring to the rear
notch.
Cut the air lock

D012224
Manual
14

D012224
Manual
15
6. After testing the unit and cleaning the underside of the
basin, adhere the lifting unit and install the plumbing.
IMPORTANT NOTICE! The
bond will be permanent
Use Sikaflex FC11 on the
support arms to adhere
the basin
IMPORTANT NOTICE! Make
sure to leave a 5 –8 mm
gap between the basin
and any walls next to it

D012224
Manual
16
2x G1/2 10mm
Cut-off valve
Hoses: L500 G1/2 or
Total L650-700mm
2x Hose
brackets
13970 Water hoses, connectors and brackets package (sold separate) contains:
2 pcs. Hose L500 G1/2, 2 pcs. G1/2 10mm Cut-off valves and 2 pcs. Hose
brackets
IMPORTANT NOTICE! The
water inlet points must not
protrude more than 45 mm
from the wall. The
openings must point
towards the floor

D012224
Manual
17
7. Install the bottom cover and tuck the excess mains wire.
Attach the excess mains wire only to the bottom cover,
not to the frame of the lifter.
IMPORTANT NOTICE!
Mind the bottom screws
when sliding the
bottom cover to place;
remember to tighten
the bottom screws.

D012224
Manual
18
8. Install the top cover and test the unit, water inlets and the
drain.