Korpinen Sense 21273100 User manual

1 OF 17
Rev. 00
In Work
K00001185.SLDDRW
21273100 Electric Sense basin lifter
installation guide

Symbols used in this manual
Warning!
Indication of potentially hazardous situation.
If not avoided, it can result in serious injury or death.
Caution!
Indication of potentially hazardous situation
which may result in minor or moderate injury.
It may also be used to alert against unsafe practices.
Notification!
This symbol is used to notify correct use and handling
of the product.
General safety
This manual must be read and understood
before use and installation. Always keep
this manual in close proximity of the
product.
The use, installation and service of this
product must follow this manual to avoid
accidents and serious personal injury.
Never use or handle this product in other
ways specified in this manual as it can
result in personal safety hazards and/or
cause damage to the product.
Persons installing and/or using this product
either as operator or user should have the
necessary safety information and access to
this manual.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or duly qualified designated persons
in order to avoid a hazard.
K00001185.SLDDRW
In Work
Rev. 00
2 OF 17

Do not perform unauthorized repairs,
disassembly or assembly operations, add-ons,
re-adjustments or modification of the product
beyond what is described in this manual. Any
use, modification or adjustment not described
in the most recent approved revision of the
manual is strictly forbidden. Do not perform
service while the product is connected to the
mains power.
This appliance can be used by minors aged
above 8 years and persons with reduced
physical, sensory or mental capabilities only
under adequate supervision and instruction
concerning the safe operation of the
appliance. The user must understand the
hazards involved. Children shall not play with
the appliance.
Do not use the product if it is defective or signs
of damage are present. If the device
produces unusual noise or smells, switch off
the mains voltage immediately.
Take care that the cables are not damaged.
Unplug the mains cable on mobile equipment
before it is moved.
The products must only be used in an
environment that corresponds to their IP
protection
Korpinen cannot be held liable if the product is
used in any way that differs from what is stated
in this manual and/or installation instruction.
Korpinen reserves the right to amend this
manual and reference documents without
prior notice.
Latest instructions are available on Korpinen's
website: https://www.korpinen.com/
3 OF 17
Rev. 00
In Work
K00001185.SLDDRW

This product is CE-marked in accordance with:
Council Directive 2006/42/EC on machinery
Council Directive 2011/65/EU, RoHS
Manufacturer name and address
Date of manufacture
Reference number
Product label symbols
Serial number
Consult manual before use
Operating interval of electrically operated equipment.
The use of electrical height adjustable equipment can
run at maximum 2 minutes, followed by an 18-minute
break.
Consult manual for important safety related
information, warnings, and safety precautions.
Class II, double isolated electrical components.
Do not dispose as unsorted municipal waste. Product
must be returned to a designated recycling station.
Mobile phones or other portable RF emitting
equipment should be no closer to the product than
30cm.
Operating and storing temperatures may not fall
outside 5-40°C
4 OF 17
Rev. 00
In Work
K00001185.SLDDRW

1
4
2
3
5
6
7
8
Exploded view
Item name Part no. Qty. Notes
1 Gaius Sense basin 62022 or 62023 1 Not included
2
Faucet with 10mm
inlet tubing
1 Not included
3
Flexible drain pipe
and inlet hoses
13982 + 13970 Not included
4 User interface 1
5 Lifting unit 1
6 Bottom cover 1
7 Top cover 1
8 Basin mount 2
Mounting hardware 6219-Z 1 Not included
5 OF 17
Rev. 00
In Work
K00001185.SLDDRW

310 60
170
80 533
490
80
80
140
215
30
Drain area
32 / 40
Water inlets.
Electrical inlet
230VAC IP44.
Max dimensions:
d80 or 80x80 mm,
height from wall
15 mm.
700
150
490
630
70
185 307
120
Mounting hole positions
IMPORTANT NOTICE! Leave a 5-8 mm gap between
the basin and any walls next to it.
6 OF 17
Rev. 00
In Work
K00001185.SLDDRW

60
560
830
100 100
Reinforced area:
20 mm plywood
with adequate
wall plugs and
8 mm deck screws.
668
136
700
103
900
7 OF 17
Rev. 00
In Work
K00001185.SLDDRW

Install the top screws.
Please leave a 10 mm
gap between the wall
and the screw head.
Drill all necessary holes
for mounting, plumbing
and electricity. Install
adequate wall plugs.
For hole positions, please
refer to page 6.
NOTICE! Follow all local
regulations and guidance
when drilling moisture
insulation.
2.
1.
IMPORTANT NOTICE! Leave a 5-8 mm gap between
the basin and any walls next to it.
8 OF 17
Rev. 00
In Work
K00001185.SLDDRW

3.
3.1 Lift the lifting unit
on top of the top screws.
Ensure the unit is installed
level before proceeding.
3.2 Tighten the
top screws.
3.3 Insert and tighten the
bottom screws.
3.4 Plug the unit to an
outlet and test it by
driving to the top and
bottom positions.
IMPORTANT NOTICE! While testing, keep hands and tools away from the
open mechanism. Before continuing work, unplug the unit.
9 OF 17
Rev. 00
In Work
K00001185.SLDDRW

4.1 Remove the basin mounts
and fasteners. IMPORTANT NOTICE!
Do not discard the basin mount or
these fasteners.
4.2 You may discard the
shipping support.
4.
10 OF 17
Rev. 00
In Work
K00001185.SLDDRW