Kramer TBUS-100XL User manual

P/N: 2900-301554 Rev 1 www.kramerAV.com
USER MANUAL
MODEL:
TBUS-100XL
Table Connection Bus

Kramer Electronics Ltd.
TBUS-100XL –Contents
i
Contents
Introduction 1
Getting Started 1
Overview 2
TBUS-100XL Table Connection Bus 3
Installing the TBUS-100XL 4
Cutting a Hole in the Table 4
Connecting the Cables 4
Mounting the TBUS-100XL in the Table 6
Using the TBUS-100XL 7
Technical Specifications 8

Kramer Electronics Ltd.
TBUS-100XL –Introduction
1
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world
of unique, creative, and affordable solutions to the vast range of problems that confront the
video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we
have redesigned and upgraded most of our line, making the best even better!
Getting Started
We recommend that you:
•Unpack the equipment carefully and save the original box and packaging materials for
possible future shipment.
•Review the contents of this user manual.
Go to www.kramerav.com/downloads/TBUS-100XL to check for up-to-date user manuals,
application programs, and to check if firmware upgrades are available (where appropriate).
Achieving Best Performance
•Use only good quality connection cables (we recommend Kramer high-performance,
high-resolution cables) to avoid interference, deterioration in signal quality due to poor
matching, and elevated noise levels (often associated with low quality cables).
•Do not secure the cables in tight bundles or roll the slack into tight coils.
•Avoid interference from neighboring electrical appliances that may adversely influence
signal quality.
•Position your Kramer TBUS-100XL away from moisture, excessive sunlight and dust.
Safety Instructions
Caution:
•This equipment is to be used only inside a building. It may only be connected to other
equipment that is installed inside a building.
•There are no operator serviceable parts inside the unit.

Kramer Electronics Ltd.
TBUS-100XL –Introduction
2
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce
the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected
and recycled. To comply with the WEEE Directive, Kramer Electronics has made
arrangements with the European Advanced Recycling Network (EARN) and will cover any
costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on
arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular
country go to our recycling pages at www.kramerav.com/il/quality/environment.
Overview
Congratulations on purchasing your Kramer TBUS-100XL Table Connection Bus.
The TBUS-100XL is an elegant furniture-mounted connection bus. The TBUS-100XL features
a mechanism for pneumatic lifting and smooth closing of its lid. It is easily installed into a table
or podium top, and its interface enables you to connect any equipment to systems installed in
a room. It has five pass-through openings for cables, located on the lower surface, enabling
closing of the lid while keeping the cables hidden and protected under the surface.

Kramer Electronics Ltd.
TBUS-100XL –TBUS-100XL Table Connection Bus
3
TBUS-100XL Table Connection Bus
This section defines TBUS-100XL and its connection surface.
Figure 1: TBUS-100XL Table Connection Bus
Figure 2: TBUS-100XL Connecting Surface
#
Feature
Function
1
Pneumatic Mechanism
Enables automatic lifting and smooth closing of the lid.
2
Outer Rim
Fits over the table surface.
3
Mounting Screws (x2)
For securing TBUS-100XL to the table.
4
Locking Butterfly Nuts (x2)
Tighten to lock the mounting butterfly screw.
5
Mounting Butterfly Nuts (x2)
Tighten to secure the unit to the table surface.
6
Mounting Brackets (x2)
For securing the unit to the table surface.
7
Black Anodized or Brushed Aluminum
Semi-Automatic Lid (with Opening for
Cable Pass-Through)
Covers the connecting surface, leaving the table surface neat
and tidy.
8
Lid Latch
For safely closing the lid.
9
Lock for latch
To secure lid.
10
Pass-Through Opening and Bushing
(x5)
Insert a cable through the opening and the bushing (inner
diameter approx. 10 mm Ø).
11
Frame Screws (x8)
For securing and adjusting the height of the frame.

Kramer Electronics Ltd.
TBUS-100XL –Installing the TBUS-100XL
4
Installing the TBUS-100XL
To install the TBUS-100XL perform the following steps:
1. Cut a hole in the table surface (see Cutting a Hole in the Table on page 4).
2. Connect the cables (see Connecting the Cables on page 4).
3. Secure the unit to the table (see Mounting the TBUS-100XL in the Table on page 6).
Cutting a Hole in the Table
1. Cut a 104mm X 97mm (5.4” to 5.5”) hole in the table in the desired location.
The thickness of the table should be 3”(76mm) or less.
2. Clean the table surface.
Take care not to damage the table. Kramer AV is not responsible for any damage caused to
the table.
Connecting the Cables
You can install the cables either before mounting the TBUS-100XL on a table, or after it is
mounted (usually if the TBUS-100XL is mounted and you need to replace the cables).
To connect the cables:
1. Insert the cables through the
pass-through openings.

Kramer Electronics Ltd.
TBUS-100XL –Installing the TBUS-100XL
5
2. Insert a cable into an opening
and place the bushing around
the cable.
3. Push the bushing into the pass-
through opening to secure.

Kramer Electronics Ltd.
TBUS-100XL –Installing the TBUS-100XL
6
Mounting the TBUS-100XL in the Table
To mount the unit:
1. Before mounting the
TBUS-100XL, pass the cables
through the unit. Insert the
TBUS-100XL into the hole cut into
the table making sure the outer
rim is firm against the surface of
the table.
2. From underneath the table, slide
the mounting brackets into the
appropriate slots.
3. Tighten the butterfly mounting
screws securely upward against
the table.
4. Lock the mounting screws into
position with the locking butterfly
screws.

Kramer Electronics Ltd.
TBUS-100XL –Using the TBUS-100XL
7
Using the TBUS-100XL
Once the TBUS-100XL is installed, you can easily customize it to your own needs by directly
plugging in the required AV equipment, as illustrated in the example in Figure 3.
Figure 3: TBUS-100XL Boardroom Installation

Kramer Electronics Ltd.
TBUS-100XL –Technical Specifications
8
Technical Specifications
Environmental
Conditions
Operating Temperature
0° to +40°C (32° to 104°F)
Storage Temperature
-40° to +70°C (-40° to 158°F)
Humidity
10% to 90%, RHL non-condensing
Regulatory
Compliance
Safety
CE, UL
Environmental
RoHS, WEEE
General
Net Dimensions (W,D)
15.5cm x 14.6cmm (6.1" x 5.7")
Shipping Dimensions (W, D, H)
27.5cm x 22cm x 19.5cm (10.8" x 8.7" x 7.7")
Net Weight
1.32kg (2.9lbs) approx.
Shipping Weight
1.9kg (4.2lbs) approx.
Specifications are subject to change without notice at www.kramerav.com