Kramer 575 User manual

575, 576 Quick Start (P/N: 2900-301037QS REV 3)
P/N:
2900- 301037QS
Rev:
3
Scan for full manual
575/576 Quick Start Guide
This guide helps you install and use your 575/576 for the first time.
Go to www.kramerav.com/downloads/575-576 to download the latest user manual and check if
firmware upgrades are available.
Step 1: Check what’s in the box
575 2-Wire Extra Range HD Transmitter /
576 2-Wire Extra Range HD Receiver
Power adapter
Bracket set
Quick start guide
Rubber feet
Step 2: Get to know your 575/576
575 2-Wire Extra Range HD Transmitter
#
Feature
Function
1
RESET Recessed Button
Press to reset the device.
2
BAUD RATE DIP-switches
Set the RS-232 baud rate (baud rate on 575 and 576 should be identical).
3
ON LED
Lights green when the device is powered.
4
LOOP OUT HDMI Connector
Connect to a local monitor.
5
HDMI IN Connector
Connect to an HDMI source.
6
TO 576 (RX)
CAT 5/6 RJ-45 Port
Connect to the RJ-45 port on 576.
7
(Connect via
one of these
options)
HD15 15-pin HD Connector
Connect to the 15-pin HD connector on 576.
8
A, B 2-pin TERMINAL BLOCK
Connector
Connect to the 2-pin terminal block connectors on 576.
9
RS-232 9-pin D-sub Connector
Bi-directional RS-232 between the devices, allowing control of the display
from the source end/control of a source from the display end.
10
5V DC
+5V DC connector for powering the unit.

576 2-Wire Extra Range HD Receiver
#
Feature
Function
1
RESET Recessed Button
Press to reset the device.
2
BAUD RATE DIP-switches
Set the baud rate (baud rate on 575 and 576 should be identical).
3
ON LED
Lights green when the device is powered.
4
FROM 575 (TX)
(Connect via
one of these
options)
CAT 5/6 RJ-45 Port
Connect to the RJ-45 port on 575.
5
HD15 15-pin HD Connector
Connect to the 15-pin HD connector on 575.
6
A, B 2-pinTERMINAL
BLOCK Connector
Connect to the 2-pin terminal block connectors on 575.
7
OUTPUTS
HDMI Connector
Connect to an HDMI acceptor.
8
S/PDIF RCA Connector
Connect to a digital audio acceptor.
9
BAL. AUDIO 5-pin Terminal
Block Connector
Connect to a stereo balanced audio acceptor.
10
RS-232 9-pin D-sub Connector
Bi-directional RS-232 between the devices, allowing control of the display
from the source end/control of a source from the display end.
11
5V DC
+5V DC connector for powering the unit.
Step 3: Install 575/576
Install 575/576 using one of the following methods:
Attach the rubber feet and place the unit on a flat surface.
Fasten a bracket (included) on each side of the unit and attach it to a flat surface.
For more information go to www.kramerav.com/downloads/575-576.
Mount the unit in a rack using an optional RK-T2B rack adapter.

Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your 575/576 devices. For best results, we recommend that
you always use Kramer high-performance cables to connect AV equipment to 575/576.
Step 5: Connect the power
Connect the 5V DC power adapters to 575/576 and plug it into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power adapter that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.
Step 6: Operate 575/576
DIP-switch Setup:
A switch that is down is on; a switch that is up is off. By default, all the switches are up (off).
Video Switching Selection:
DIP-switch 1
DIP-switch 2
DIP-switch 3
Baud Rate
OFF (up)
OFF (up)
OFF (up)
2400
ON (down)
OFF (up)
OFF (up)
4800
OFF (up)
ON (down)
OFF (up)
9600
ON (down)
ON (down)
OFF (up)
19200
OFF (up)
OFF (up)
ON (down)
28800
ON (down)
OFF (up)
ON (down)
38400
OFF (up)
ON (down)
ON (down)
57600
ON (down)
ON (down)
ON (down)
115200

Technical Specifications
575
Inputs
1 HDMI
On a female HDMI connector
Outputs
1 LOOP HDMI
On a female HDMI connector
CAT 5/6
On an RJ-45 connector
VGA
On a 15-pin HD connector
2-wire
On a 2-pin terminal block connector
Ports
RS-232
On 9-pin D-sub connector for serial link extension
576
Inputs
CAT 5/6
On an RJ-45 connector
VGA
On a 15-pin HD connector
2-wire
On a 2-pin terminal block connector
Outputs
1 HDMI
On a female HDMI connector
1 S/PDIF
On an RCA connector
1 Balanced Stereo Audio
On a 5-pin terminal block connector
Ports
RS-232
On 9-pin D-sub connector for serial link extension
General
Video
Max Resolution
1080p60
Compliance
HDCP 1.4
Audio
Support
2.0 channel PCM, 48kHz/44.1kHz sampling rate
Bandwidth
12kHz
Analog THD + NOISE
0.08% @1kHz at nominal level
Extension Range
Full HD (1080p @60Hz)
Up to 600m (2000ft)
Extended RS-232
Baud Rate
2400 to 115200, selectable
Controls
Front Panel
ON LED indicator
Baud rate DIP-switches
Reset recessed button
Power
Consumption
5V DC, 1.5A
Source
5.2V DC, 4A
Cooling
Convection Ventilation
Environmental
Conditions
Operating Temperature
0° to +40°C (32° to 104°F)
Storage Temperature
-40° to +70°C (-40° to 158°F)
Humidity
10% to 90%, RHL non-condensing
Regulatory
Compliance
Safety
CE, UL
Environmental
RoHs, WEEE
Enclosure
Size
Mega Tool
General Information
(per device)
Net Dimensions (W, D, H)
18.75cm x 11.5cm x 2.54cm (7.4" x 4.5" x 1")
Shipping Dimensions (W, D, H)
34.5cm x 16.5cm x 5.2cm (13.6" x 6.5" x 2.1")
Net Weight
0.46kg (1lbs) approx.
Shipping Weight
0.96kg (2.1lbs) approx.
Type
Aluminum
Accessories
Included
2 Power adapters, 2 power cords
Specifications are subject to change without notice at www.kramerav.com