Kraus KGW-1700 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV. September 17, 2020
Single Lever Vessel Glass Waterfall
Bathroom Faucet
KGW-1700
R
INSTALLATION MANUAL

2
Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your
receipt with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

Prior to Installation:
·Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
Customer Service at 800-775-0703 for a replacement.
·Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.
Clean sink or countertop to remove any debris, plumber’s putty, or
silicone.
·Flush angle stops to release any debris prior to installation.
·Pre-drilled hole size requirement: 1 3/8" (min)
·Max countertop thickness: 1 3/8”
3
Tools Required
Adjustable Wrench Phillips Screwdriver
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
Pipe Tape

44
Diagram and Parts List
1. Decorative Ring
2. Glass Disc
3. Lever
4. Seal for Glass Disc
5. Faucet Body
6. Mounting Hardware
A. Rubber Washer
B. Metal Washer
C. Mounting Nuts
D. Mounting Screws
7. Hot & Cold Waterlines
8. Hex Wrench
1
2
3
4
5
8
6A
6B
6C
6D
7

55
Installer Tip:
Shut off main water supply before installing new faucet.
Faucet Dimensions
7 1/8"
(181mm)
12.5°
2 1/8"
(54mm)
1/16"~1 3/4"
(1mm~44mm)
2 3/8"
(59mm)
22"
(560mm)
7 5/8"
(195mm)
12.5°
12.5°
58.2°
3 1/2"
(90mm)
6 1/8"
(155mm)
3/8" Compression
10 3/8"
(265mm)
11 1/4"
(286mm)
12 5/8"
(322mm)
Ø2 5/8"
(Ø67mm)
5/16"~3/8"
(7.2mm~8.8mm)
12.5°

66
Step 2. Remove decorative ring
Remove decorative ring (1)
from faucet body (5).
Step 1. Remove mounting hardware
Remove mounting hardware
(6A, B, C, & D) from the
mounting pipe.
6A
6B
6C
6D
1
5

7
Step 3. Install glass disc
Install glass disc (2) on faucet
body (5). Secure it using
decorative ring (1).
Step 4. Install faucet
Insert faucet body (1) into
the hole on the countertop.
Attach rubber washer (6A),
metal washer (6B), mounting
nut (6C), and mounting screws
(6D) from underneath the sink.
1
2
5
56A
6B
6C
6D
Forward
Backward NOTE: Hand-tighten only
(decorative ring)

8
Step 5. Secure mounting hardware
Adjust direction of faucet body
(5). Tighten mounting nut (6C)
until snug. Tighten mounting
screws (6D) to nut with a
Phillips head screwdriver until
snug.
Step 6. Connect waterlines to main valve
Connect hot and cold waterlines
(7) to the angle stops. Tighten
with a wrench until snug. Turn
on hot and cold angle stops and
check for leaks.
Cold
Blue Line
Red Line
Hot NOTE:Make sure O-rings
are installed on both
ends of the hot & cold
waterlines

9
Open
Hot
Cold
Step 7.
Turn water on for a minute to
ensure proper water flow.

Replacement Parts
1. Decorative Ring & O-ring
2. Glass Disc
3. Lever
4. Seal for Glass Disc
6. Cartridge
7. Flow Restrictor
8. Mounting Hardware
9. Hex Wrench 2mm
Replacement Parts List Finish/Color Part #
KP44083
N/A
KP44084
KP44085
KP44086
KP44087
KP44088
KP44075
KP44090
KP44022
CH, SN, ORB, SFS*
5. Locking Nut
*Denotes faucet component color options:
CH - Chrome
SN - Satin Nickel
ORB - Oil Rubbed Bronze
SFS - Spot Free Stainless Steel
2
3
4
5
6
9
8
7
1
CH, SN, ORB, SFS*
10. Filter Washers
10